Nautel NX400 Manuale utente
NX400 Transmitter
Installation Manual
Document:NHB-NX400-INS
Issue: 1.0 2017-06-30
Status: Standard
Nautel Limited
10089 Peggy’s Cove Road
Hackett’s Cove, NS Canada B3Z 3J4
Phone: +1.902.823.3900 or
Toll Free: +1.877.6NAUTEL (6628835) (Canada & USA only)
Fax: +1.902.823.3183
Nautel Inc.
201 Target Industrial Circle
Bangor, Maine USA 04401
Phone: +1.207.947.8200
Fax: +1.207.947.3693
Customer Service (24 hour support)
+1.877.628.8353 (Canada & USA only)
+1.902.823.5100 (International)
Email: [email protected]
Web: www.nautel.com
The comparisons and other information provided in this document
have been prepared in good faith based on publicly available
information. The reader is encouraged to consult the respective
manufacturer's most recent published data for verification.
© Copyright 2017 NAUTEL. All rights reserved.
NX400 Installation Manual Table of contents
Page v
Contents
Release control record ix
Preparing for installation 1-1
Unpacking and positioning 2-1
Completing cabinet assembly 3-1
Connecting transformer taps and secondary wiring 4-1
Connecting the station reference ground 5-1
Connecting ac power 6-1
Adjusting the spark gap 7-1
Installing audio inputs 8-1
Planning complete? 8-1
Routing cables and connecting audio inputs 8-1
Installing control/monitor wiring 9-1
Planning complete? 9-1
Routing cables 9-1
NX400 Installation Manual Table of contents
Page vi Issue 1.0 2017-06-30
Commissioning tasks 10-1
Pre-commissioning tasks 10-1
Commissioning 10-3
Going on-air 10-7
Network Setup 10-8
Parts and tools 11-1
Contacting Nautel 11-1
Parts supplied by Nautel 11-1
Parts not supplied by Nautel 11-2
Parts ordering 11-2
Module replacement program 11-2
Tools for installation 11-3
Pre-installation / Installation assistance 12-1
Pre-installation consulting 12-1
Installation and commissioning service 12-1
Online documentation 12-3
On-site support 12-3
Training 12-3
Standard warranty 12-4
Extended warranties 12-8
List of terms 13-1
NX400 Installation Manual
Issue 1.0 2017-06-30 Page ix
Release control record
Issue Date Reason
1.0 2017-06-30 Initial release of NX400 (NARA67). Supports
software version NX SW 4.7 and higher.
NX400 Installation Manual
Page x Issue 1.0 2017-06-30
NX400 Installation Manual Preparing for installation
Issue 1.0 2017-06-30 Page 1-1
Section 1: Preparing for installation
Before installing your NX400 transmitter, perform the following steps:
1. Ensure that you have performed the pre-installation tasks described in the
NX400 Pre-installation Manual.
2. Make sure that you received all the components. (Check your packing list.)
3. Inspect all crates and packages for damage. Inspect the tip and drop indicators attached to
the crates to determine if a crate has been tipped over or has been subjected to excessive
shock (see Figure 1.1).
Figure 1.1: Tip and Drop Indicators
4. Report any damage immediately to your Nautel sales representative and the carrier.
5. Move the crates as close as possible to the transmitter’s planned location.
NX400 Installation Manual Preparing for installation
Page 1-2 Issue 1.0 2017-06-30
6. Unpack the crates in accordance with the instructions provided on the outside of the crates.
• For each crate, remove the panel labelled open this side. The panel is attached using
Philips head screws.
• Remove any visible packing material, including braces, from the crate's interior.
•Remove the remaining outer plywood shell by unscrewing the outer wood panels from
the pallet under the transmitter.
7. Review any assembly notes or instructions contained inside the transmitter crates. (For sites
requiring custom configurations, the instructions provided with the transmitter replace the
instructions provided here.)
8. Gather the parts and tools you will need for installation. For a list of required tools, see
“Parts and tools” on page 11-1.
9. When you are ready to install the NX400 transmitter, follow the steps shown in Figure 1.2
on page 1-3.
TIP When you have completed a task or step, put a check mark beside the step
number.
CAUTION:
FAILURE TO COMPLY WITH RECOMMENDATIONS MAY VOID YOUR MANUFACTURER’S
WARRANTY. FOR MORE INFORMATION, REVIEW YOUR WARRANTY DOCUMENTS.
Indice
Altri manuali Nautel Trasmettitore
Nautel
Nautel NX100 Manuale utente
Nautel
Nautel XR12 Manuale utente
Nautel
Nautel VS2.5 Manuale di programmazione
Nautel
Nautel GV20 Manuale utente
Nautel
Nautel VS300 Manuale utente
Nautel
Nautel NV40 Manuale di programmazione
Nautel
Nautel XR12 Manuale di programmazione
Nautel
Nautel NV5LT Manuale di programmazione
Nautel
Nautel ND500II Manuale del proprietario
Nautel
Nautel XR6 Manuale di programmazione
Nautel
Nautel NX50 Manuale utente
Nautel
Nautel VX150 Manuale utente
Nautel
Nautel VS300 Manuale utente
Nautel
Nautel ND500II-113-x21 Manuale utente
Nautel
Nautel NX50 Manuale utente
Nautel
Nautel NX5 AM Manuale
Nautel
Nautel VS300 Manuale utente
Nautel
Nautel GV30N Manuale di programmazione
Nautel
Nautel NV20LT Manuale utente
Nautel
Nautel XR3 Manuale utente
