Nautel NX5 Manuale utente

2: INSTALLATION MANUAL

NX5/NX3

AM TRANSMITTER

Document ID: NHB-NX3-NX5-INS

Version: 3.1

Issue Date: 2021-04-22

Status: Standard

VERSION 3.1 2021-04-22 PAGE 2.III

NX5/NX3 INSTALLATION MANUAL

Contact Information

Nautel Limited

10089 Peggy’s Cove Road

Hackett’s Cove, NS Canada B3Z 3J4

Toll Free: +1.877.6NAUTEL (662.8835)

(Canada & USA only) or

Phone: +1.902.823.3900 or

Fax: +1.902.823.3183

Nautel Inc.

201 Target Industrial Circle

Bangor, Maine USA 04401

Phone: +1.207.947.8200

Fax: +1.207.947.3693

Customer Service (24-hour support)

+1.877.628.8353 (Canada & USA only)

+1.902.823.5100 (International)

Email: [email protected]

Web: www.nautel.com

The comparisons and other information provided in this document have

been prepared in good faith based on publicly available information.

For verification of materials, the reader is encouraged to consult the

respective manufacturer's most recent publication on the official

website or through contact with Customer Service.

© Copyright 2021 NAUTEL. All rights reserved.

NX5/NX3 INSTALLATION MANUAL TABLE OF CONTENTS

VERSION 3.1 2021-04-22 PAGE 2.V

CONTENTS

Contact Information 2.1.iii

Release Control Record 2.vii

Preparing for installation 2.1.1

Unpacking and Positioning 2.2.1

Connecting the Station Reference Ground 2.3.1

Connecting Ac Power 2.4.1

Adjusting the Spark Gap 2.5.1

Installing Audio Inputs 2.6.1

Planning Complete? 2.6.1

Routing Cables and Connecting Audio Inputs 2.6.1

Installing Control/Monitor Wiring 2.7.1

Planning Complete? 2.7.1

Routing Cables 2.7.1

Configuring Remote Inputs 2.7.5

Commissioning Tasks 2.8.1

Pre-Commissioning Tasks 2.8.1

Commissioning 2.8.2

Going On-Air 2.8.9

Network Setup 2.8.10

NX5/NX3 INSTALLATION MANUAL TABLE OF CONTENTS

PAGE 2.VI VERSION 3.1 2021-04-22

Parts and tools 2.9.1

Contacting Nautel 2.9.1

Parts Supplied by Nautel 2.9.2

Parts Not Supplied by Nautel 2.9.2

Parts Ordering 2.9.2

Module Replacement Program 2.9.2

Tools for Installation 2.9.3

Pre-installation / Installation assistance 2.10.1

Pre-Installation Consulting 2.10.1

Installation and Commissioning Service 2.10.1

Online Documentation 2.10.2

On-Site Support 2.10.3

Training 2.10.3

Standard Warranty 2.10.4

Extended Warranties 2.10.7

List of terms 2.11.1

NX5/NX3 INSTALLATION MANUAL

VERSION 3.1 2021-04-22 PAGE 2.VII

Release Control Record

ISSUE DATE REASON

3.0 2019-06-01 Supports NX5/NX3 hardware NARA66B implementing

NAP39C RF Power modules and a shielded arc detector

assembly. Supports NX SW version 5.0 and higher.

3.1 2021-04-22 Implemented Castor Kit update.

NX5/NX3 INSTALLATION MANUAL

PAGE 2.VIII VERSION 3.1 2021-04-22

NX5/NX3 INSTALLATION MANUAL PREPARING FOR INSTALLATION

VERSION 3.1 2021-04-22 PAGE 2.1.1

SECTION 2.1: PREPARING FOR INSTALLATION

Before installing your NX5/NX3 transmitter, perform the following steps:

1. Ensure that you have performed the pre-installation tasks described in the

NX5/NX3 Pre-Installation Manual

.

2. Make sure that you received all the components. (Check your packing list.)

3. Inspect all crates and packages for damage. Inspect the tip and drop indicators attached to the

crates to determine if a crate has been tipped over or has been subjected to excessive shock (see

Figure 2.1.1).

Figure 2.1.1: Tip and drop indicators

4. Report any damage immediately to your Nautel sales representative and the carrier.

5. Move the crates as close as possible to the transmitter’s planned location.

6. Unpack the crates in accordance with the instructions provided on the outside of the crates.

For each crate, remove the panel labelled open this side. The panel is attached using Phillips

head screws.

Remove any visible packing material, including braces, from the crate's interior.

Remove the remaining outer plywood shell by unscrewing the outer wood panels from the

pallet under the transmitter.

NX5/NX3 INSTALLATION MANUAL PREPARING FOR INSTALLATION

PAGE 2.1.2 VERSION 3.1 2021-04-22

7. Review any assembly notes or instructions contained inside the transmitter crates. (For sites

requiring custom configurations, the instructions provided with the transmitter replace the

instructions provided here.)

8. Assemble your parts and tools. For a list of required tools, see “Parts and tools” on page 2.9.1.

9. When you are ready to install the NX5/NX3 transmitter, follow the steps shown in Figure 2.1.2 on

page 2.1.2.

Figure 2.1.2: Flowchart - Installing the transmitter

TIP When you have completed a task or step, put a check mark beside the step number.

CAUTION! FAILURE TO COMPLY WITH RECOMMENDATIONS MAY VOID YOUR

MANUFACTURER’S WARRANTY. FOR MORE INFORMATION, REVIEW YOUR

WARRANTY DOCUMENT.

Unpacking and Positioning - see page 2.2.1

Connecting the Station Reference Ground - see page 2.3.1

Installing Control/Monitor Wiring - see page 2.7.1

Commissioning Tasks - see page 2.8.1

Perform operational tasks:

“Commissioning”, “Modulation Checks” and “Going On-Air”, beginning on page 2.8.2

Connecting Ac Power - see page 2.4.1

Installing Audio Inputs - see page 2.6.1

Adjusting the Spark Gap - see page 2.5.1

Altri manuali per NX5

1

Questo manuale è adatto per i seguenti modelli

1

Indice

Manuali Trasmettitore popolari di altre marche

NIVELCO

NIVELCO EasyTREK SCA-300 Series Manuale del proprietario

Honeywell

Honeywell 5816WMBR Manuale utente

Kamstrup

Kamstrup READy MTU Istruzioni operative

Omega

Omega ZW Series Manuale utente

ABB

ABB Field 264H Guida

Alinco

Alinco DJ-V17T Manuale utente

Dejero

Dejero EnGo 3x Manuale utente

Rosemount

Rosemount 4600 Manuale utente

Speaka Professional

Speaka Professional 2342740 Manuale utente

trubomat

trubomat GAB 1000 Manuale utente

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Manuale utente

Rondish

Rondish UT-11 Manuale utente

MG

MG 10JRE Manuale utente

Burkert

Burkert 8177 Manuale utente

Firetide

Firetide HotPort 3203 Manuale

Tele Radio

Tele Radio T9-02 Manuale utente

Rotronic

Rotronic HygroFlex HF3 Series Manuale utente

Jamara

Jamara FCX6 Pro Tel Manuale utente