NEC XN120 2OPBOX Manuale utente

This guide explains the installation, configuration and operation of the XN120 2OPBOX.

Further information will be supplied with any optional equipment that you have purchased.

Please keep all information supplied for future reference.

Regulatory Notice.

Refer to the Getting Started Guide (991409-5) supplied with the XN120 Main Unit for the Declaration

of Conformity related to the product.

Warning: This is a class A product. In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate measures.

XN120

2OPBOX Guide

Rev 1.1 February 2005

991419-5

Contents

2 XN120 2OPBOX Guide

What is the 2OPBOX? ..........................................................................................................................................3

Installation Procedure ..........................................................................................................................................3

1- Unpack the 2OPBOX ........................................................................................................................................3

2- Fitting the 2OPBOX ..........................................................................................................................................4

3- Install the Option Cards...................................................................................................................................6

4- Connect the Power & System Start Up ..........................................................................................................7

5- Test the 2OPBOX..............................................................................................................................................8

Configure the XN120 ............................................................................................................................................8

XN120 2OPBOX

XN120 2OPBOX Guide 3

What is the 2OPBOX?

· The 2OPBOX is an optional unit that connects to the side of either a XN120 main unit or expansion unit.

· One box can be connected to each of the XN120 main/expansion units.

· The 2OPBOX provides two universal slots for the installation of Basic Rate ISDN cards or Voice over IP

resource cards.

Installation Procedure

1 Unpack the 2OPBOX

2 Fit the 20OPBOX

3 Install the BRI/VoIP cards into

the 2OPBOX

4 Power on the XN120

5 Test the 2OPBOX

1- Unpack the 2OPBOX

The 2OPBOX is supplied with 6 screws to fix the unit to the XN120 main/expansion cabinet.

Additional Items Required:

Cross head screwdriver.

Small cutters/pliers.

Optional Items

The 2OPBOX can have BRI cards or VoIP cards installed.

2OPBOX

Cable access to the cards

installed in the 2OPBOX

XN120

XN120 2OPBOX

4 XN120 2OPBOX Guide

2- Fitting the 2OPBOX

! You must power off the system before the 2OPBOX is connected onto the XN120 unit.

1 You will need a minimum of

690mm x 680mm (W x H) wall

space for each XN120 cabinet

with the 2OPBOX connected.

The XN120 unit with 2OPBOX

connected is 490mm x 279mm

(W x H)

!You will need more space if

you are installing the optional

expansion units.

Refer to the installation

instructions supplied with the

unit.

The 2OPBOX does not require fixing to the wall, it is fixed directly to

the XN120 unit.

2 Remove the lid of the

2OPBOX

3 Power off the XN120. You must also power off any XN120 expansion units if they are

installed.

4 Using a pair of small cutters or

pliers carefully remove the 3

breakouts on the right side of

the XN120 base unit.

You will need to remove the lid

of the XN120 first.

Remove the 3 breakouts on the right side of the XN120 unit

Have 200mm below the system

for other cables connected to the

system.

Have 100mm on

the left side of

the system for

the power cable.

Have 200 mm above

the system for

ventilation.

Have 100mm

on the right

side.

Loosen

the two

screws.

Lift off

the lid

XN120 2OPBOX

XN120 2OPBOX Guide 5

5 Push the 2OPBOX into the

connector on the right side of

the XN120 cabinet

6 Secure the 2OPBOX using the

screws supplied.

There are two screws with self

tapping thread and four with a

machined thread.

2OPBOX

XN120

2 self tapping screws

4 machine screws

2OPBOX

XN120 2OPBOX

6 XN120 2OPBOX Guide

3- Install the Option Cards

1 Install the BRI or VOIP option

cards into the 2OPBOX.

Refer to the instructions

supplied with each card for

further details.

The card can be installed into either slot of the 2OPBOX.

If you are only installing one option card, it is recommended (for logical

port configuration) that you fit the card into the slot marked CN1.

2 Secure the card to the ETH

plate at the front edge of the

2OPBOX.

Fit the option

card into the

guides and

push firmly

onto the

connector.

Secure to the

ETH plate.

XN120 2OPBOX

XN120 2OPBOX Guide 7

4- Connect the Power & System Start Up

1 Power on the XN120. ! System Start Up – Retain Customer Configuration

This is the normal operation for powering the XN120 on.

Before you power on the system check that the NORMAL switch is set

to ON. This will ensure that the system memory retains your

configuration.

The NORMAL switch is located to the right of the MOH/Page

connector on the main unit, refer to the Getting Started Guide supplied

with the XN120 for further information.

2 The BRI/VOIP card(s) will be

automatically configured.

Refer to the instructions supplied with the option card for configuration

details.

XN120 2OPBOX

8 XN120 2OPBOX Guide

5- Test the 2OPBOX

1 When the 2OPBOX is installed

it will provide 2 slots.

The slot numbers depend on which XN120 cabinet that the 2OPBOX

is connected to.

The 2OPBOX connected to the main cabinet will provide slots 5 & 6

The 2OPBOX connected to expansion cabinet 1 will provide slots 11 &

The 2OPBOX connected to expansion cabinet 2 will provide slots 17 &

The slots used by the cards within the 2OPBOX can be confirmed by

Program 10-03-01.

Refer to the instructions supplied with either the BRIU or VOIPU card

for details of the settings within Program 10-03-01.

2 Replace the lid of the

2OPBOX.

Configure the XN120

There is no configuration related to the 2OPBOX, the cards within it require configuration. Refer to the

instructions supplied with either the BRIU or VOIPU card.

Secure

the two

screws.

Locate the lid

onto the right

side edge of

the 2OPBOX

and lower into

place.

Indice

Altri manuali NEC Centralino

NEC

NEC NEAX 2400 IPX Manuale del proprietario

NEC

NEC Univerge SV9300 Manuale utente

NEC

NEC ELECTRA ELITE IPK II Manuale del proprietario

NEC

NEC NEAX 2400 ICS Manuale utente

NEC

NEC Univerge SV9100 Manuale utente

NEC

NEC Univerge SV9100 Guida rapida

NEC

NEC UX5000 Manuale utente

NEC

NEC SV8300 Manuale utente

NEC

NEC SL1000 Manuale del proprietario

NEC

NEC Univerge SV8100 Manuale utente

NEC

NEC SL1000 Manuale del proprietario

NEC

NEC SV8300 Istruzioni per l'installazione

NEC

NEC DS2000 IntraMail Manuale utente

NEC

NEC SL1000 Manuale utente

NEC

NEC SL1100 Manuale utente

NEC

NEC ASPILA EX Manuale utente

Manuali Centralino popolari di altre marche

Allo.com

Allo.com Nano 2 Manuale utente

ZYCOD

ZYCOD ZX50 Manuale utente

Panasonic

Panasonic KX-TDA100BX Manuale utente

LV switch

LV switch IPPBX800 Manuale di istruzioni

Edge-Core

Edge-Core VST3305 Manuale utente

Panasonic

Panasonic KX-T7625 - Digital Proprietary Speakerphone 24... Manuale utente

Rauland-Borg

Rauland-Borg Telecenter IV Manuale utente

Grandstream Networks

Grandstream Networks UCM6208 Manuale utente

ATCOM

ATCOM IPPBX IP02 Manuale utente

Panasonic

Panasonic KX-TVS50 - 2 Port Voicemail System Manuale utente

bintec elmeg

bintec elmeg elmeg hybird 600 Manuale utente

Panasonic

Panasonic KX-NS300 Manuale utente

MCK

MCK EXTender PBXgateway Manuale utente

Panasonic

Panasonic KX-NS300CN Manuale del proprietario

Epygi

Epygi Quadro Quadro 2xi Manuale utente

SMC Networks

SMC Networks TigerVoIP SMCPBX10 Manuale utente

AGFEO

AGFEO AC 14 analog Manuale utente

Nortel

Nortel QSY22 Manuale utente