NetComm NTC-220 Manuale utente

Recovery via Recovery Console

Guide

NTC-220 Series

Doc No. FA01392

NTC-220 Series – Recovery via Recovery Console Guide

2 of 6

FA01392 v1.0 28 September 2021

NetComm Wireless Limited was acquired by Casa Systems, Inc. a Delaware company on 1 July 2019. The information

contained herein is proprietary to Casa Systems, Inc. No part of this document may be translated, transcribed, reproduced, in

any form, or by any means without prior written consent of Casa Systems, Inc..

Trademarks and registered trademarks are the property of NetComm Wireless Limited or their respective owners.

Specifications are subject to change without notice. Images shown may vary slightly from the actual product.

Note – This document is subject to change without notice.

Document history

This document relates to the following products:

NetComm NTC-221/NTC-222/NTC-223/NTC-224/NTC-227

VER. DOCUMENT DESCRIPTION DATE

v1.0

Initial release.

28 September 2021

Table i. - Document revision history

NTC-220 Series – Recovery via Recovery Console Guide

3 of 6

FA01392 v1.0 28 September 2021

Applicable devices

This document is applicable only to the following NetComm Wireless devices:

•NTC-22X

The screenshots used in this document were taken using an NTC-22X. The same process can be applied to all the applicable

devices listed above.

Recovering an NTC-220 series router in case of

problems with the Main operating system

The NTC-220 series router features two independent operating systems, each with their own file systems. These two systems

are referred to as 'Main' and 'Recovery'. It is always possible to use one in order to restore the other in the event that one

system becomes damaged or corrupted (such as during a firmware upgrade failure). The recovery console provides limited

functionality and is typically used to restore the main firmware image in the case of a problem.

This document outlines the process of booting an NTC-220 series router into recovery mode and flashing the main firmware

image to restore functionality in the case where a failure has occurred.

Accessing recovery mode

Both systems have web interfaces that can be used to manipulate the other inactive system. The router starts up by default

in the Main system mode, however the router may be triggered to start in recovery mode if desired.

To start the router in recovery mode:

Power off and unplug the device, connect the Ethernet connection.

Press and hold the physical reset button on the interface panel

While holding the reset button, plug in the power cable

Hold the reset button for further for 10 to 15 seconds. When the LEDs on the front panel change to amber and

countdown in a sequence, release the reset button. The router then boots into recovery mode.

In your browser, navigate to http://192.168.1.1

The router’s recovery mode is hardcoded to use this address regardless of the IP address that was configured in the

main system. The router’s recovery console is displayed.

Installing the main firmware image

Click on the Application Installer menu item at the top of the screen.

NTC-220 Series – Recovery via Recovery Console Guide

4 of 6

FA01392 v1.0 28 September 2021

Click on the Browse button.

Locate the firmware image on your computer. Firmware images always have a “.cdi” extension and the latest versions

are always downloadable from the product support page on https://support.netcommwireless.com/products/NTC-

220%20Series

Click the Open button.

Click the Upload button to begin the transfer of the firmware file to the router.

When the file has completed uploading, click on the Install link next to the firmware image file.

NTC-220 Series – Recovery via Recovery Console Guide

5 of 6

FA01392 v1.0 28 September 2021

Click on the OK button to begin the installation.

When the installation is complete, the router displays “Installation is successful!” and returns to the file list.

To ensure that the router runs correctly, it is necessary to perform a restore to the factory default settings. This means

that any previous settings on the router are erased.

NTC-220 Series – Recovery via Recovery Console Guide

6 of 6

FA01392 v1.0 28 September 2021

Click on Settings menu item at the top of the screen.

Click on the Retore button.

The router resets all settings to the factory defaults and reboots to the main firmware.

The recovery process is complete.

Altri manuali per NTC-220

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali NetComm Router di rete

NetComm

NetComm NTC-6000 SERIES Manuale utente

NetComm

NetComm NTC-140W Series Manuale utente

NetComm

NetComm NTC-220 Guida rapida

NetComm

NetComm 3GT1Wn Manuale utente

NetComm

NetComm NB750 Manuale utente

NetComm

NetComm NF15ACV Manuale utente

NetComm

NetComm NF5 Manuale utente

NetComm

NetComm NP5410 Manuale utente

NetComm

NetComm 3G27WV-02 Manuale utente

NetComm

NetComm NB6PLUS4WN Manuale utente

NetComm

NetComm G.SHDSL 4-port Security Modem Routers NB712 Manuale utente

NetComm

NetComm 4G100W Manuale utente

NetComm

NetComm NTC-400 Series Manuale utente

NetComm

NetComm NTC-6200-02 Manuale di istruzioni

NetComm

NetComm NB2800 Manuale utente

NetComm

NetComm NF20 Manuale utente

NetComm

NetComm NTC-6000 SERIES Istruzioni per l'installazione

NetComm

NetComm NB5540 Manuale utente

NetComm

NetComm RTA1030W Manuale utente

NetComm

NetComm Liberty 3G17Wn Manuale

NetComm

NetComm Freshtel NB9 Manuale utente

NetComm

NetComm NWL-15 Manuale utente

NetComm

NetComm NB6PLUS4W Guida per l'amministratore

NetComm

NetComm 3GM1WN Manuale utente

Manuali Router di rete popolari di altre marche

Allnet

Allnet ALL0333AU Manuale utente

HomeSeer

HomeSeer HT-SEL Manuale utente

Sercomm

Sercomm Genesis OC3505D Manuale utente

Billion

Billion BIPAC 5102 Series Manuale utente

TP-Link

TP-Link TD-8817 Manuale utente

Motorola

Motorola MR1900 Manuale utente

Digi

Digi IX14 Manuale utente

Cisco

Cisco NCS 540 Manuale

XAVi

XAVi X8821e Manuale utente

BEC

BEC 6200WZL Manuale utente

MikroTik

MikroTik hAP ac3 Series Manuale utente

Korenix

Korenix JetNet 5428G Series Manuale utente

NETGEAR

NETGEAR FS526T - Switch Manuale utente

Korenix

Korenix JetNet 5710G Series Manuale utente

Automated Logic

Automated Logic ZN551 Manuale del proprietario

Cisco

Cisco ASR 1000 Series Manuale dell'operatore

EnGenius

EnGenius ESR-9710 Manuale utente

Cisco

Cisco 805 Series Istruzioni operative e di sicurezza