NetComm NF2 Manuale utente
NETCOMM FIBRE™ SERIES
Dual Band WiFi
Gigabit Hub
NF2 - Quick Start Guide
Connecting the antenna
and cables
1
1. Connect the supplied antenna to the circular antenna port on the back of the NetComm
NF2. This should be attached onto the port in a clockwise direction.
2. If connecting by Ethernet WAN, connect an RJ-45 Ethernet cable from the blue WAN port
of the NF2 to one of the Ethernet LAN Ports on your modem/Fibre termination point.
3. If connecting by 3G/4G, connect your USB modem to the 3G/4G USB port on the side of
the router.
4. Connect the supplied power adapter into a wall socket and switch on the power.
5. Connect the power adapter to the NF2 and press the on/off button to power the router on.
Allow up to 60 seconds for the router to boot up.
Modem/Fibre ONT
Antenna
Connecting to the router via an
Ethernet cable
2
1. Connect an RJ-45 Ethernet cable from one of the yellow Ethernet LAN Ports on the
back of the NF2 to the LAN port of your computer.
2. Wait approximately 30 seconds for the connection to be established
Computer
Login to the web interface
3
1. Open a web browser (Internet Explorer, Firefox and Safari), type 192.168.20.1 into the
address bar and press Enter/Return.
2. At the login screen, type “admin” (without the quotes) into both the Username and the
Password elds and click “OK”.
3. The “First-Time Setup Wizard” will then be displayed. Click on the “Yes, let’s get
started with the wizard” button to congure your device.
1. If connecting to an ADSL modem or a Fibre termination device, select “WAN”as the
WAN interface.
2. Select “Dynamic IP Address” as the WAN type and press the “Next” button.
3. To enable a backup connection via 3G/4G, tick the checkbox and enter the appropriate
3G/4G connection information as supplied by your 3G/4G provider (see the instructions
on Step 5 of this quick start guide).
You will also need to enter a high availability website in the Remote Host box in order to
verify that your WAN based internet connection remains active.
4. Click “Next” to complete the wizard. Please see from step 6 in this quick start guide for
how to complete the wizard
Router Setup - WAN
4
5
1. Select your country of residence and your service provider from the dropdown
boxes and the network name (APN) will automatically appear.
2. Enter your username/password and SIM PIN if required as supplied by your 3G/4G
provider. Not all 3G/4G providers require a username and password or a SIM PIN
3. Click “Next” to complete the wizard. Please see from step 6 in this quick start guide
for how to complete the wizrad
Router Setup - 3G/4G
Completing the wizard
6
2.4GHz WiFi
1. Select to enable or disable your wireless network (Wireless on/off), show or hide
your wireless network (SSID Broadcast) or change the wireless network name (SSID
Broadcast Name). After making the appropriate changes, click “Next”. (If you do not
want to change the default settings, simply click “Next”)
2. Select the wireless security type and wireless security key you would like to use on
your wireless network and click “Next”. (If you do not want to change the default
settings, simply click “Next”)
5GHz WiFi
3. Repeat the steps above for the 5GHz WiFi setup
4. Enter the username and password you would like to use when logging into the web
based user interface. Conrm the new password by entering it a second time in the
“Retype Password” eld and click “Next”. (If you do not want to change from the
default settings of admin/admin, simply click “Next”)
5. Review your selected settings and click “Finish”. If you would like to change any of
the settings, click “Back” until you reach the required page and adjust your settings
accordingly. Click “Next” until you reach the summary page again.
The router will attempt to connect using the details entered. This can take up to 2 minutes.
If the connection attempt was successful, the Internet Connection LED on the front of
the unit will then be lit.
Connecting via WiFi
7
Laptop Gaming Console
Smart Phone IPTV
2.4 GHz 5 GHz
You can connect multiple wireless devices, including laptops, desktops and PDA’s to your
router by following these two basic steps.
1. Using your wireless device, scan the wireless networks and select the wireless network
name listed on the included Wireless Security Card and then click connect.
Please note: If you have changed the wireless network name during set-up, select the wireless network displaying the new
name you entered.
2. Enter the wireless security key listed on the included Wireless Security Card.
Please note: If you changed the wireless security password during set-up, enter the new password you entered.
3. Wait approximately 30 seconds for the connection to establish
8
1. If a USB mass storage device is plugged into the File Storage USB port, it will be
auto detected
2. You can access the les on the storage device from any computer connected to
the router
3. To access the les, open a web browser and type \\NAS\.
4. You will need to enter the same username and password that allows access to the
web user interface to access the les. The default username and password is “admin”
(without quotes)
USB Storage
USB storage device
Altri manuali per NF2
5
Indice
Altri manuali NetComm Interruttore
NetComm
NetComm 3G38WV-TS Istruzioni operative e di sicurezza
NetComm
NetComm NP3005 Manuale utente
NetComm
NetComm NP2160 ProSwitch Manuale utente
NetComm
NetComm NP1201 Manuale utente
NetComm
NetComm NP2624M Manuale utente
NetComm
NetComm NCT240 Manuale utente
NetComm
NetComm 3G38WV-TS Manuale utente
NetComm
NetComm NP2624M Manuale utente
NetComm
NetComm NCT480 Manuale utente
NetComm
NetComm NP3024 Manuale utente
NetComm
NetComm NP2500 Manuale utente
NetComm
NetComm 3G27WV-R Manuale utente
NetComm
NetComm NP3016 Manuale utente
NetComm
NetComm NCT240 Manuale utente
NetComm
NetComm ROGERS LIBERTY Series Manuale utente
NetComm
NetComm NP2724M Manuale utente
NetComm
NetComm 3G38WV-TS Istruzioni operative e di sicurezza
NetComm
NetComm NP2724M Manuale utente
NetComm
NetComm NP2008 Manuale utente
NetComm
NetComm NP3005 Manuale utente
