NiceRF RF24L01F20 Manuale utente
2.4G
RF24L01F20
TEL:0755-61596687 FAX:0755-27838582 www.nicerf.com 第1页 共 5页
RF24L01F20
1. Description
RF24L01F20 Module is a high integrated wireless module,
which worked in 2.4GHz of ISM band. RF24L01F20 adopts
Nordic’s RF chip nRF24L01+ and high efficiency RF amplifier.
The feature of high data rate (maximum 2Mbps ), good sensitivity
（-102 dBm）
but low harmonic
and low unexpected
radiation
extend the range and improve the
link performance.
2. Features
Frequency Range：
Maximum power output：20dBm
Sensitivity up to:-102dBm@250Kpbs
Data rate：250K,1Mpbs,2Mpbs
GFSK Modulation,
FIFO: 32bytes
Ultra low power off mode
Support functions of frequency hopping
Internal integrated voltage regulator
operating voltage range：1.9-3.6 V
operating temperature range：-40~+85°C
3. Application
Wireless remote control
Remote meter reading
Smart Home
Personal data records
Toy control
Tire Pressure Monitoring
health monitoring
Tag reader
2.4G RF module with amplifier
2400-2480MHZ
RF24L01F20
TEL:0755-61596687 FAX:0755-27838582 www.nicerf.com 第2页 共 5页
4.Schematic
5. Electrical Characteristics
★Below parameters is measured at 3V.
Parameter
Min.
Type.
Max.
Unit
Conditions
Operation conditions
Operating voltage range
1.9
3.3
3.6
V
Operating temperature range
-40
85
℃
Current consumption
RX Current
23.5
24
mA
TX Current
135
150
mA
@20dBm
Sleep Current
<1
uA
RF parameters
Frequency range
2400
2525
MHZ
Modulation rate
250
2000
Kbps
GFSK
Output power range
4
20
dBm
Power 0=5dBm,3=20dBm
Maximum output power
18.5
20
dBm
RX sensitivity
-100
-102
dBm
@data=250kbps
RF24L01F20
TEL:0755-61596687 FAX:0755-27838582 www.nicerf.com 第3页 共 5页
6.Typical application circuit
7.Pins Configuration
Pin No.
Pin Definitions
Description
1
VCC
Connect to VCC（1.9-3.6V）
2
GND
Connect to ground
3
CE
Chip enable
4
CSN
CSN of SPI interface
5
SCK
SCK or SPI interface
6
MOSI
MOSI of SPI interface
7
MISO
MISO of SPI interface
8
IRQ
Interrupt output, active low
9
ANT
Connect 50ohm coaxial antenna
10
GND
Connect to ground
11
GND
Connect to ground
RF24L01F20
TEL:0755-61596687 FAX:0755-27838582 www.nicerf.com 第4页 共 5页
8.Mechanical Dimension:
Appendix：
The module is equipped with a standard DEMO board for customer to debug the program and test distance.
It shows as below:
RF24L01F20
TEL:0755-61596687 FAX:0755-27838582 www.nicerf.com 第5页 共 5页
The LCD Full Segment is as below:
Users can set the parameters of the RF module such as working mode /frequency / transmitter power / transmission
data rate through the buttons, and measure the wireless communication distance.
Working Mode
1) Master Mode: Send 1 packet per second, and waiting for the acknowledge;
2) Slave Mode: Stay in Rx mode to wait for the data from the master, it will send back the acknowledged signal after
received the data from the master.
3) Tx Test Mode: RF module continuously transmit signal;
4) Rx Test Mode: RF module is always in Rx mode;
5) Standby Mode: RF module is always in standby state.
Button Operation
1) [SET] Button
Press the [SET] button to enter into setting mode; Or press the [SET] button to be out of the setting mode upon
the last parameter is done.
2) [UP/Down] Button
In setting mode, press the [UP/Down] button to increase/decrease the value of flash icon.
Note: The DEMO board has FLASH memory inside, all the setting parameters will be saved automatically and keep
unchanged even power-off.
Note: The antenna(s) used for this transmitter must not be co-located or operating in conjunction with any other
Only those antenna(s) tested with the device or similar antenna(s) with equal or lesser gain may be used with
this transmitter
antenna or transmitter
The RF2401F20 module is designed to comply with the FCC statement. FCC ID is 2AD66-RF2401F20.
The host system using RF2401F20, should have label indicated it contain modular’s FCC ID 2AD66-RF2401F20
FCC Information and Copyright
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
—Consult the dealer or an experienced radio/TV technician for help.
15.19 Labelling requirements.
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1)This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may
cause undesired operation.
changes or modifications not expressly approved by the party responsible for compliance could
void the user's authority to operate the equipment.
Indice
Altri manuali NiceRF Unità di controllo
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
