Nikon D5200 Manuale utente
1
Please read the safety instructions before using the
device. Read this Quick Setup Guide for the correct setup
and installation.
Technical data of the equipment and general safety:
Mains connection
Voltage: 100VAC to 240VAC 50/60 Hz
Eletrical Safety: CE conformity
Climatic conditions
ONLY use in dry rooms!
Temperature: 0 to max. 40 °C
Operating humidity: 0% bis 80 % r.F, non-condensing
Operating altitude: 0 to 2000m above sea level
Additional Safety Information:
oPlace the appliance on a flat, stable, and vibration-free surface such as a desk. Choose a dry,
well-ventilated area out of direct sunlight. Do not place the device on a carpet to protect it
from dust.
oDO NOT place objects on the device .
oDO NOT slide in any objects through the slots of the device
They may touch dangerous current carrying parts or cause a short circuit and resulting in a
fire or electric shock.
If objects made of metal, water or other liquids get into the unit, unplug the power cord
immediately.
INSTALLATION MANUAL rev. 1.1
Vizoo xTex
!
2
oDO NOT use flammable substances, spray, or organic solvent / liquids containing alcohol or
ammonia to clean the inside or outside of the device. Otherwise fire or electric shock can
occur. Turn off the device when it is not in use for more than an hour. Unplug the power
cord when not using the unit for more than one day.
oDO NOT use the device if the power cord is damaged to avoid electric shock or fire.
oDO NOT connect the camera (neither DC nor USB) when the xTex device is switched on. This
can cause serious damage to the xTex device.
oWhen you are leaving the office or not using the xTex device for several hours always switch
the device off using the main power switch.
Repair, Product liability and Warranty Service:
Do not attempt to repair this product yourself, as opening or removing covers may expose
you to dangerous current-carrying parts and other risks and may void your warranty.
For repair service please contact the support: support@vizoo3d.com
Do not use the unit in a humid environment or near water sources, such as hand basins etc.
Avoid the use of this device during a thunderstorm.
Declaration of Conformity (Europe only):
We, Vizoo GmbH
Johann-Karg-Str. 30, 85540 Haar, Deutschland
declare, that this product is in compliance with the essential requirements of the directives
2006/95/EG and 2004/108/EG.
The declaration of conformity can be found on our website:
http://vizoo3d.com/xtex/EC-Declaration-of-Conformity.pdf
3
1. Unpack the equipment and check the package
contents
Make sure that the device is always moved or lifted by two people. Reset the unit carefully
and be careful to not pinch your fingers.
For packaging plastic bags and other packaging elements made of plastic were used. Keep
them out of reach from babies and children to prevent suffocation.
Housing
Camera (Nikon D5200, Nikon
D800, Nikon D810 or Nikon
D850)
Lens (model might differ
from image)
!
4
Camera Manual (Nikon,
possibly no paper copy
available)
Download link:
https://customers.vizoo3d.com/manual_d5200_en
https://customers.vizoo3d.com/manual_d800_en
https://customers.vizoo3d.com/manual_d810_en
https://customers.vizoo3d.com/manual_d850_en
Camera Mount
Power cable (Inlet
connector)
USB Connector cable to PC
5
Camera Power Adapter
(Nikon EP-5A or Nikon EP-5B,
can be pre-installed)
Camera Screw (with or
without seal)
Fixing Screw (for Camera
Mount)
Calibration chart (model
might differ from image)
6
2. Device Overview
Power indication light
Pullout
Capturing surface
Camera mount guide
Pullout (open)
Device housing
Lens bracket
7
Power supply
(camera)
USB port (camera)
USB port (PC)
Main Power switch
(on/off)
Mains connection
Electronics
8
3. Installation of the Camera mount
•First, set the camera mount into the guide on top of the housing. Make sure that the
shorter side of the bracket is in the guide.
•Then turn the fixing screw into the thread of the guide. Tighten the screw slightly so
that the camera position can still be moved in the guide.
•Then set the camera screw into the hole provided on the longer side of the camera
mount.
9
4. Mounting the Camera
Please carefully read the safety instructions and the instructions on how to attach the lens in
the camera's manual before you start with the installation.
•Assemble the lens to the camera as described in the camera's manual.
•In case it has not already been installed: Insert the power connector into the camera
as described in the User Guide of the power connector.
•Insert the camera to the opening of the lens bracket with the lens facing down and
the rear display facing up.
For this and the following steps make sure to always keep at least one hand on the camera
lens. Make sure that the camera is sitting on the lens bracket with its full weight and is
covering the opening completely.
•Slide the camera mount close to the bottom of the camera.
•Now move the camera screw in the slot of the camera mount to the height of the
camera's tripod socket (see camera manual).
•Tighten the camera screw.
•As last step tighten the fixing screw, so that the camera mount can no longer be
moved.
!
!
10
5. Connecting the device
DO NOT connect the camera (neither DC nor USB) when the xTex device is switched
on. This can cause serious damage to the xTex device.
•Connect the camera USB cable.
Nikon D5200 only:
(In case the cable is not already installed)
Connect the plug of the USB cable with the female connector of the USB extension
cable.
In case the cable is not already installed:
Connect one end of the USB cable with the USB port of the camera and the other end
with the USB port of the device.
•Connect the camera power cable.
Connect one end to the plug of the power connector and insert the special connector
to the jack of the device’s camera power supply.
The special connector has 4 pins and a groove at the bottom. Insert the plug fully into
the socket first, and then turn the knurled bezel clockwise.
•Connect the USB connector cable to the PC.
Connect the end of the cable to the jack on the unit and the other end to the PC.
Connect the power cord (Inlet plug) to the power connector of the device.
The device must be connected to a grounded, easily accessible AC outlet. Do not handle the
power plug with wet hands to prevent electric shock.
!
!
Altri manuali per D5200
5
Indice
Altri manuali Nikon Macchina fotografica digitale
Nikon
Nikon Coolpix S225 Manuale utente
Nikon
Nikon F3AF Manuale utente
Nikon
Nikon Coolpix S4100 Manuale utente
Nikon
Nikon 1 J1 Manuale utente
Nikon
Nikon D3100 Manuale utente
Nikon
Nikon COOLPIX AW1100 Manuale utente
Nikon
Nikon D2X Manuale utente
Nikon
Nikon COOLPIX 570 Manuale utente
Nikon
Nikon D7200 Manuale utente
Nikon
Nikon EL2 Manuale utente
Nikon
Nikon D500 Istruzioni utente
Nikon
Nikon CoolPix S70 Manuale utente
Nikon
Nikon COOLPIX AWIOO Manuale utente
Nikon
Nikon D2H Manuale utente
Nikon
Nikon Z50 Manuale utente
Nikon
Nikon 1 S1 Manuale utente
Nikon
Nikon 6.1 Manuale del proprietario
Nikon
Nikon 1 S2 Manuale utente
Nikon
Nikon D5300 Manuale utente
Nikon
Nikon N2020 AF Manuale utente
