Nordson EFD 750V Manuale
750V, 750V-SS and 751V
Dispense Valves
MAINTENANCE & PARTS GUIDE
IMPORTANT!
Save this Sheet.
Forward to
Maintenance or
Tool Crib
Supervisors
Electronic pdf files of EFD®manuals are also available at
www.efd-inc.com/manuals.html.
For EFD sales and service in over 30 countries,
contact EFD or go to www.efd-inc.com/contact
EFD, Inc.
East Providence, RI USA
800-556-3484; +1-401-434-1680 (outside the USA)
EFD International Inc.
Dunstable, Bedfordshire, UK
0800 585733 or +44 (0) 1582 666334
Ireland 00800 8272 9444
[email protected] www.efd-inc.com
EFD, Inc., Asia
China: +86 (21) 5854 2345
[email protected] www.efd-inc.com/cn
A NORDSON COMPANY
Fluid Body
1. Remove the two retainer screws.
2. To reinstall the fluid body, align fluid
body holes with diaphragm and air
cylinder body holes and reinsert
retainer screws. Tighten in accor-
dance with the following torque
specifications:
newton
Fluid body meters (inch pounds)
Acetal (black) 1.58 Nm (14 inch pounds)
UHMW*(yellow) 0.79 Nm (7 inch pounds)
Stainless steel 1.58 Nm (14 inch pounds)
*Ultra High Molecular Weight
Diaphragm
3. Back-out stroke control knob two
turns counterclockwise from the
closed position.
4. Remove fluid body.
5. Unscrew diaphragm (counter-
clockwise) and remove it from
the piston rod.
6. Thread-on the new diaphragm
and tighten with medium pressure.
7. Align the holes of the diaphragm
with the appropriate holes in the
air cylinder body by inserting a
flat tip screwdriver through the
hole in the stroke control knob
and engage piston rod slot.
8. Rotate rod, piston and diaphragm
assembly clockwise until holes
are aligned.
9. Reinstall fluid body.
10. Turn stroke control knob clock-
wise until closed, and then
reopen to approximate stroke.
12
4
5
6
7
9
11
Valve Disassembly and
Reassembly Procedures
CAUTION: To prevent damage, the valve
must be disassembled starting at the fluid
outlet end of the valve.
Diaphragm
UHMW
Fluid body
Tip Adapter
Fluid inlet fitting
(2) Retainer
screws
#7524
Fluid body
Tip
Adapter
Fluid inlet fitting
751V assembly
www.efd-inc.com [email protected] USA 800-556-3484 Europe +44 (0) 1582 666334 Asia +86 (21) 5854 2345
Sales and service of EFD dispensing systems are available worldwide.
Piston spring #7525
Anti-torque washer
#7533
Piston retainer ring
#7526
Piston and rod
includes O-ring
#7518
Air input hose & fitting
#78518A
Air cylinder body
#7527-SS (stainless steel)
#7527 (hard-coated aluminum)
750SR-KIT
750V
750SSR-KIT
750V-SS
Stroke control knob
#750SR-KIT (stroke reference, aluminum)
#750SSR-KIT (stroke reference,
stainless steel)
Piston O-ring
11. Remove fluid body and diaphragm.
12. Remove stroke control knob and
spring by turning counterclockwise.
13. Remove the piston retainer ring and
anti-torque washer.
14. Remove the piston.
15. Lubricate O-ring, piston shaft and air
cylinder wall with Nye Lubricant #865.
16. Reinstall components in reverse order
of disassembly.
Tools required:
7/64" hex wrench
1/8" flat-tip screwdriver
6" adjustable wrench
6" needle-nose pliers
snap-ring pliers
Replacement Parts for Specific Valve Models
——— Fluid Body ———
Model UHMW Acetal Stainless* Fluid Inlet Fitting Tip Adapter Diaphragm
750V &
750V-SS 7521 n/a 7521-SS* 7511BP (1/8” ID Tube) 7514 7510
751V n/a 7521D 7521D-SS 7611BP (1/4” OD Tube) 7514B 7510
7610BP (3/8” OD Tube)
*optional
3
810
12
13
14
15
16
www.efd-inc.com [email protected] USA 800-556-3484 Europe +44 (0) 1582 666334 Asia +86 (21) 5854 2345
Sales and service of EFD dispensing systems are available worldwide.
Troubleshooting Guide
No fluid flow
•If valve operating air pressure is too low,
the valve will not open. Increase air
pressure to 70 psi (4.8 bar) minimum.
•The reservoir air pressure may not be
high enough. Increase pressure.
•The dispensing tip may be clogged.
Replace tip.
•The stroke adjustment may be closed.
Open stroke adjustment.
•Fluid may have solidified in the valve.
Clean the fluid body.
Fluid drools after the valve closes,
eventually stopping
•This is caused when air is trapped in the
outlet section of the fluid chamber or the
fluid has entrapped air. The air will expand
after the valve closes, causing extrusion
until the air reaches atmospheric pressure.
Purge the valve by dispensing at a steady
flow until clear. If a small tip is used, it
may be necessary to remove the tip while
purging to obtain sufficient flow to carry
the air down through the tip adapter.
•If the fluid has entrapped air, the material
must be degassed before dispensing.
Fluid drips at a steady rate after the
valve closes
•A steady drip can be caused by exces-
sive reservoir pressure. Check to be
sure the reservoir pressure is not above
70 psi (4.8 bar).
•If the stroke adjustment knob is turned-out
more than two full turns, resulting in reser-
voir pressure that will force the diaphragm
open. Check the stroke adjustment knob
to be sure it is less than two turns out.
•A steady drip also indicates failure of
the diaphragm to close fully due to par-
ticle build-up or wear. In either case,
replace the sealing head in accordance
with the maintenance instructions.
Fluid leaks out between fluid body and
diaphragm
•Fluid leakage between the fluid body and
diaphragm indicates the annular seal-
ing ridge on the fluid body is damaged or
the fluid body is distorted due to exces-
sive torque on the retaining screws. In
either case, replace the fluid body.
Fluid flows out of the drain hole
•Fluid flowing out of the drain hole indicates
a ruptured diaphragm. Replace in accor-
dance with the maintenance instructions.
Valve responds slowly when opening
and closing
•Valve response is related to control air
hose length and size. The valve is sup-
plied with 5-feet of 3/32” ID tubing
attached. Any additional length or size
change will affect response time. Check
to be sure the length and size have not
been changed.
Inconsistent deposits
•Inconsistent deposits can result if the
air pressure controlling the valve and/or
supplying the reservoir is fluctuating or if
the valve operating pressure is less than
70 psi (4.8 bar). Check to be sure air
pressures are constant and the valve
operating pressure is 70 psi (4.8 bar).
•The time the valve is open must be con-
stant. Check to be sure the valve con-
troller is providing a consistent output.
A NORDSON COMPANY
USA: 800-556-3484 or +1-401-434-1680
Europe: 0800 585733 or +44 (0) 1582 666334
Asia: +86 (21) 5854 2345
[email protected] www.efd-inc.com
©2006 Nordson Corporation 750V-MAINT-01 v062606
Questo manuale è adatto per i seguenti modelli
2
Altri manuali Nordson EFD Unità di controllo
Nordson EFD
Nordson EFD 752V Series Manuale
Nordson EFD
Nordson EFD 781Mini Series Manuale utente
Nordson EFD
Nordson EFD 754V-SS Manuale
Nordson EFD
Nordson EFD 754V-SS Manuale utente
Nordson EFD
Nordson EFD 741MD-SS Series Manuale
Nordson EFD
Nordson EFD Liquidyn P-Jet SolderPlus Manuale utente
Nordson EFD
Nordson EFD 782RA Manuale
Nordson EFD
Nordson EFD 7860C-RS Manuale utente
Nordson EFD
Nordson EFD 741V Series Manuale utente
Nordson EFD
Nordson EFD 725HF Manuale utente
Nordson EFD
Nordson EFD 725HF Series Manuale utente
Nordson EFD
Nordson EFD 725HF-SS Manuale
Nordson EFD
Nordson EFD 745NC Manuale utente
Nordson EFD
Nordson EFD 736HPA-NV Manuale
Nordson EFD
Nordson EFD 736HPA Manuale
Nordson EFD
Nordson EFD 725DA-SS Manuale
Nordson EFD
Nordson EFD 750 Series Manuale utente
Nordson EFD
Nordson EFD 752V-HL Manuale utente
Nordson EFD
Nordson EFD 781S Series Manuale utente
Nordson EFD
Nordson EFD 725HF-SS Manuale
Manuali Unità di controllo popolari di altre marche
Festo
Festo Compact Performance CP-FB6-E Manuale elenco delle parti
Elo TouchSystems
Elo TouchSystems DMS-SA19P-EXTME Manuale utente
JS Automation
JS Automation MPC3034A Manuale utente
JAUDT
JAUDT SW GII 6406 Series Guida rapida
Spektrum
Spektrum Air Module System Manuale utente
BOC Edwards
BOC Edwards Q Series Manuale utente
