North Creek Echo Manuale utente



        

              

              

    !     " # $  ! 

                    %

         

                  

         

&     '  

&     '  &     '  

&     '  

Qty Part

(woofer)

2 2.20mH 16 AWG inductor

2 20.0uF Blue film capacitor

2 2.74 Ohm NORTH resistor

(tweeter)

2 8uF Yellow film capacitor

2 0.56mH 16 AWG inductor

2 3.32 Ohm NORTH resistor

2 6.19 Ohm NORTH resistor

(connectors, etc.)

8 Big Ring Jr

20 #10-10 AWG ring tongues

2 large crimp barrels

4 0.25" quick connects

4 0.110" quick connect

8 long black tie wraps

2 4" x 5" pegboard

2 4" x 3" pegboard

1 8" buss bar

18 brass screws

18 brass nuts

2 foot solder

2 each Red, Black, White, Blue 3/8 x 1" shrink tube

(wire, inches)

16 18 awg insulated jumper wire

32 black Tef-Flex

32 Black Lex

32 Red Lex

96 (8 ft) Blue Tef-Flex

64 (5 ft 4") White Tef-Flex

Required Tools:

These are the basic tools required to complete this project. The items listed below are all available from MCM

Electronics, www.mcmonline.com, 800-453-4330. The tools suggested are the least costly that will do the job.

There are certainly better quality tools out there for considerably more money. The brands that seem to be the best

are Xcelite, Ideal and Klein. MCM also carries all of these brands.

Always solder in a well ventilated area.

Tool: MCM Part Number MCM $

Wire Cutter/Stripper 22-1635 $ 4.99

Crimper 22-1780 10.05 (#22-1795 by Klein is better, twice the price)

Soldering Iron (80 Watt) 21-4345 8.23

Soldering Iron Holder 21-3525 1.49

Heat Gun 21-7315 17.95

3/8" nut driver or flat head screw driver

colored nail polish

Wire Prep:

Cut the wire to the appropriate length, strip 1/2" from all ends, and either leave bare or attach, crimp and solder the

appropriate connection as indicated by the table below.

Quantity Material Length one end other end

2 black Tef-Flex 16" 1/2" bare 1/2" bare

2 black Lex 16" 1/2" bare 0.110" quick connect

2 red Lex 16" 1/2" bare 0.110" quick connect

2 blue Tef 16" 1/2" bare 0.250" quick connect

4 blue Tef 16" 1/2" bare 1/2" bare

2 white Tef 16" 1/2" bare gold Big Ring Jr.

2 white Tef 16" 1/2" bare 0.250" quick connect

2 2.2mH inductor long 1/2" bare gold Big Ring Jr on long inner lead

2 0.56mH inductor 5" both 1/2" bare 1/2" bare

4 18 awg jumper 4" 1/2" bare 1/2" bare

2 buss bar 4" all bare the easy way to strip the buss bar is to slice

off the insulation with a drywall knife

Capacitor Prep:

For the 20uF blue cap, attach one piece of jumper wire to each solder terminal

Resistor Prep:

With the label up, bend both leads straight down, then bend 1/4" of each end straight out (into an "L"). This method

allows the legs to function both as the connectors and as the means of suspending the resistor body above the board.

Please read the North Creek Wiring Guide, included with the kit package

Woofer Network Assembly

Closely inspect our crossover assembly diagram. This is built on a 3x4 board.

"Attach" means "slide all leads into a single ring tongue crimping section, crimp, and solder

Attach the 16" black Tef-Flex wire to one lead of the 2.74 Ohm resistor.

Attach the other end of the 2.74 Ohm resistor and one end of the 20uF Blue cap.

Attach the two remaining lead of the 20uF, the outside lead from the 2.20mH inductor, and the

16" red woofer lead in a single ring tongue.

Attach the 16" black Tef wire and the stripped end of the 16" black Lex wire with a single gold

Big Ring Jr.

When everything cools down, drop three brass screws through the rear of the pegboard as

indicated on the assembled crossover diagram. Flip the board over and drop the ring sections

over the screws, attach with the nuts, tighten, and drop nail polish on the exposed threads.

Shoot a little silicone under the capacitor and bind it and the inductor lead to the pegboard with a

single tie wrap as shown on our diagram. It is very important that the inductor lead is

secured under the tie wrap and in the silicone.

Shrink black shrink tube over the crimped section of the gold Big Ring Jr that holds the two

black wires.

Shrink red shrink tube over the crimped section if the gold big Ring Jr that is attached to the

2.20mH inductor.

Carefully inspect the assembly to make sure everything is exactly as our assembled crossover

diagram.

Tweeter Network Assembly

Carefully inspect our assembled network diagram. This is a 4x5 board.

"Attach" means "slide all leads into a single ring tongue crimping section, crimp, and solder

Attach the stripped end of the 16" white wire to the gray leads of the 8uF Yellow cap with a

single ring tongue

Attach one 16" blue wire to the outside lead of the 0.56mH inductor

Attach one 16" blue wire to one lead of one of the 6.19 Ohm resistor

Attach the stripped 3" buss bar to one lead of the other 3.32 Ohm resistor

Attach the free leads of both resistors and the 16" white Tef wire with a single ring tongue.

When everything cools down, attach the resistor sub-assembly to the peg board and tighten down

the brass nuts to hold everything in place.

Attach the capacitor sub-assembly to the pegboard as indicated on our crossover diagram.

Attach the free end of the buss bar, the free end of the 0.56mH inductor, and the free lead from

the 8uF Yellow cap with a single large crimp barrel.

When everything cools down, shoot a little silicone under the capacitor and secure it and the buss

bar/capacitor/inductor connection point with a long tie wrap. Make sure the buss bar is not

touching any other connection, and coat it with silicone.

Drop the inductor into place on the pegboard, loosely secure with tie wraps, add a little silicone

under the inductor, tighten the tie wraps, trim excess

Attach the inductor-blue wire ring tongue to the pegboard

Attach the stripped ends of all three 16" blue leads with a single gold Big Ring Jr.

Heat shrink white shrink tube over the crimp section of the Big Ring Jr attached to the 16" white

lead.

Heat shrink blue shrink tube over the crimp section of the Big Ring Jr attached to the three blue

wires.

Carefully inspect the assembly to make sure everything is exactly as our assembled crossover

diagram.

        

PO Box 1120

Old Forge NY 13420

www.NorthCreekMusic.com

Indice

Altri manuali North Creek Altoparlanti

North Creek

North Creek Big Kat North D28 Manuale utente

Manuali Altoparlanti popolari di altre marche

argon audio

argon audio IE20 Manuale utente

Denon

Denon SC-N7 Manuale utente

Gemline

Gemline Ace 3952 Manuale utente

Focal

Focal ON WALL 300 Manuale di istruzioni

HEADRUSH

HEADRUSH Maximus HRSP 5024 Manuale utente

SoundLogic

SoundLogic BCCS-6/6395 Manuale utente

Peavey

Peavey DTH 218 Manuale utente

Avantree

Avantree Pluto Air Manuale utente

Morel

Morel Integra Series INTEGRA OVATION 4 Manuale utente

Oppo

Oppo SONICA Manuale utente

Bose

Bose SoundLink Wireless Music System Manuale utente

Rocksteady

Rocksteady Stadium Manuale utente

Bowers & Wilkins

Bowers & Wilkins 4 Manuale utente

Sonance

Sonance SONOS OUTDOOR Series Manuale utente

Electro-Voice

Electro-Voice EVID FM4.2 Manuale utente

Pioneer

Pioneer XW-HTD630 Manuale utente

Onn

Onn BWA16AA002 Manuale utente

HP GL313AA - USB Speakers PC Multimedia Manuale utente

North Creek echo Manuale utente

Manuali Altoparlanti popolari di altre marche