Notifier LDM-32 Istruzioni per il montaggio

Page 1 of 4

1 Product Overview

The LDM Lamp Driver Modules (LDM-32, LDM-E32, and LDM-R32) are used to drive lamps or LEDs in a

custom mimic connected to an addressable fire panel.

2 Installation

WARNING: Remove all power sources to the panel before installation. Leave the

external and main power OFF until installation is complete.

2.1 Mounting a LDM Module to a CHS Chassis

1. Screw two 3/4” stand-offs onto the mounting studs of a CHS chassis.

2. Place the module on the CHS chassis. Ensure the tab on the module slides into the slot on the

CHS chassis.

3. Secure the module with two 4-40 screws.

Figure 2-1 - Mounting the LDM to a CHS Chassis

2.2 Mounting a LDM Relay Expander

The LDM-R32 can either be mounted alongside a LDM module or expander in the CHS chassis (see

section 2.1 for CHS mounting), or stacked on top of a LDM module using the standoffs provided (see Figure

2-2.)

Make sure to connect the Relay Power Ribbon Cable between the LDM-R32 and the LDM Module, as

shown in Figure 2-3.

DOC-03-091

9 Columbia Way

Baulkham Hills, NSW 2153

PH 02-9894-1444 • FAX 02-9894-4193

www.notifier.com.au

LDM Lamp Driver

Installation Sheet - Released

26/03/2015 Rev A

Page 2 of 4

Figure 2-2 –Mounting a LDM-R32 on top of

a LDM Module

Figure 2-3 - Connecting the Relay Power

Ribbon Cable

2.3 Connections

NOTE: When cables are not run in a conduit, shielding on cables for EIA-485

connections must be grounded outside the enclosure and fire panel. See the LDM

Series Instruction Manual for more information.

Figure 2-4 –Power (TB1) and ACS Comms (TB2) connections to the CPU

Figure 2-5 - Connecting LDM-E32 expander modules with the ribbon cable

LDM-32

(or LDM-E32) LDM-R32

Chassis

Standoff Standoff

J10

9.;>

>=D2?

J11

J5 J6 J7 J8

TB4

J5 J6 J7 J8 J10

K6 K27

K28

K29

K30

K31

TB1

K32

LDM-32

(or LDM-E32)

LDM-R32

Relay Power Ribbon Cable connection

OUT

CPU Board

120

EOL



First

LDM-32

Last

LDM-32

NC Supervision

Inputs

OUT

EGnd

NC Supervision

Inputs

OUT

EGnd

NC Supervision

Inputs

OUT

EGnd

Page 3 of 4

Figure 2-6 - Lamp/LED Wiring for 5 V DC

Figure 2-7 - Lamp/LED Wiring for 24 V DC

NOTE: All LEDs must be in the same room as the LDM modules.

3 Configuration

3.1 Setting the Address and Operating Modes

Figure 3-1 - Rotary address & DIP switches on the LDM-32

NOTE: The available address range for the LDM-32 is 2-32 (inclusive.)

1. Set a unique address for the LDM-32 using the rotary address switches along the side of the

module.

2. Set the operating mode using the DIP switches on the LDM-32. See Table 1 for a description of the

switch functions.

3. Configure annunciator points via the panel’s keypad or through VeriFire Tools. Refer to the panel’s

Programming Manual for further information on programming the annunciator.

J11

Common

SWITCH LAMP

POWER

J7 J8

J10

Custom

Graphic

Display

System

Trouble LED

(Yellow)

Point Status LEDs:

Use RED for Alarm points

YELLOW for Trouble points, and

GREEN for Output points.

Use 680 , 1.4 W resistors

for each point if using 2 mA LEDs.



Custom

Graphic

Display

System

Trouble LED

(Yellow)

Point Status LEDs:

Use RED for Alarm points

YELLOW for Trouble points, and

GREEN for Output points.

Use 10K , 1.4 W resistors

for each point if using 2 mA LEDs.



LDM-32

Lamp Driver Address

Set in the range 02-32

Ones

Tens

DIP Switch SW3

ALARM/TROUBLE mode

ALARM ONLY mode

12345678

SW4

Switch set to

positionOFF

Page 4 of 4

Switch

Bank

Switch

No.

Default

Setting

Description

SW3

OFF

Turn ‘ON’ when the lamp driver is used to control relays.

OFF

Configures the number of expander modules.

See Table for details.

OFF

Not used.

OFF

Turn ‘ON’ for Receive Only mode, to mirror another LDM at the

same address in a different location.

OFF

Turn ‘ON’ for Piezo Disable, to disable the buzzer from sounding

for any event.

OFF

Turn ‘ON’ for Switch Inhibit, to disable point control switches on

the annunciator.

OFF

Turn ‘ON’ for Flash Inhibit, to disable the flashing of LEDs for

unacknowledged events. Also disables piezo.

N.B.: Flash Inhibit must be ON when using the LDM-R32.

Table 1 –DIP Switches and Default Settings

No.

DIP Switch Settings

None

Table 2 - Number of Expanders

4 Supplemental Documentation

For information on...

Refer to...

Doc No.

Operating modes

LDM Series Instruction Manual

15885

Programming

AFP-3030 Australian Programming Manual

DOC-01-032

AFP-3030 New Zealand Programming Manual

DOC-01-038

XLS-3000A Australian Programming Manual

DOC-01-035

XLS-3000A New Zealand Programming Manual

DOC-01-041

Notifier NCA-2 Australian Manual

DOC-01-043

Notifier NCA-2 New Zealand Manual

DOC-01-045

Honeywell NCA-2 Australian Manual

DOC-01-044

Honeywell NCA-2 New Zealand Manual

DOC-01-046

Table 3 - Supplemental Documentation

2 3

1 2

Position OFF

Position

2 3

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Notifier Unità di controllo

Notifier

Notifier FDM-1 Manuale utente

Notifier

Notifier FMM-1 FlashScan Manuale utente

Notifier

Notifier NAM-232 Manuale utente

Notifier

Notifier FZM-1 Manuale utente

Notifier

Notifier XP6-R Manuale utente

Notifier

Notifier FDM-1 Manuale utente

Notifier

Notifier XP10-M Manuale utente

Notifier

Notifier 020-553 Manuale di istruzioni

Notifier

Notifier NCM-W Manuale dell'operatore

Notifier

Notifier IDR-MD Manuale utente

Notifier

Notifier XP6-MA Manuale utente

Notifier

Notifier TM-4 Manuale tecnico

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente