Nvent Eriflex Flexibar UDF500 Manuale utente

5 mm

Position 15.5 mm

ERIFLEX FLEXIBAR

as shown

86.0

16.1 13.3

NOTE:

1. Tighten screws of all unused galleries to the specified torque above.

2. For multiple phase assemblies, join blocks together before installing on DIN profile.

3. The input must be fixed or maintained at approximately 15cm from the block.

I: 500A

Ui: 1000V AC/DC

Uimp: 12kV

Ipk: 51kA

Icw: 23kA rms 1s

IEC 60947-7-1

(IEC 60947-7-1 Ratings)

INSTRUCTION SHEET

UDF500

569060 N

WARNING:

nVent products shall be installed and used only as indicated in nVent product instruction sheets and training materials. Instruction sheets are available at

www.nVent.com

and from your nVent customer service representative.

nVent products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.

All instructions must be

completely

followed to ensure proper and safe installation and performance.

Improper installation, misuse, misapplication or other failure to completely follow nVent's instructions and warnings may cause product malfunction, property

damage, serious bodily injury and/or death, and void your warranty.

SAFETY INSTRUCTIONS:

All governing codes and regulations and those required by the job site must be observed.

Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.

nVent, nVent CADDY, nVent ERICO Cadweld, nVent ERICO Critec, nVent ERICO, nVent ERIFLEX, and nVent LENTON are owned by

nVent or its global affiliates. All other trademarks are the property of their respective owners. nVent reserves the right to change

specifications without prior notice.

1 OF 2

IP7805_S

TECHNICAL SUPPORT

www.nVent.com

3/16"

Position 15.5 mm

ERIFLEX FLEXIBAR

as shown

#10

3.39

.63 .52

NOTE:

1. Tighten screws of all unused galleries to the specified torque above.

2. For multiple phase assemblies, join blocks together before installing on DIN profile.

335A

600V AC/DC

UL 1059

(UL1059 Ratings)

INSTRUCTION SHEET

UDF500

569060 N

WARNING:

nVent products shall be installed and used only as indicated in nVent product instruction sheets and training materials. Instruction sheets are available at

www.nVent.com

and from your nVent customer service representative.

nVent products must never be used for a purpose other than the purpose for which they were designed or in a manner that exceeds specified load ratings.

All instructions must be

completely

followed to ensure proper and safe installation and performance.

Improper installation, misuse, misapplication or other failure to completely follow nVent's instructions and warnings may cause product malfunction, property

damage, serious bodily injury and/or death, and void your warranty.

SAFETY INSTRUCTIONS:

All governing codes and regulations and those required by the job site must be observed.

Always use appropriate safety equipment such as eye protection, hard hat, and gloves as appropriate to the application.

nVent, nVent CADDY, nVent ERICO Cadweld, nVent ERICO Critec, nVent ERICO, nVent ERIFLEX, and nVent LENTON are owned by

nVent or its global affiliates. All other trademarks are the property of their respective owners. nVent reserves the right to change

specifications without prior notice.

2 OF 2

IP7805_S

TECHNICAL SUPPORT

www.nVent.com

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali nvent Unità di controllo

nvent

nvent Eriflex Flexibar UDF250 Manuale utente

nvent

nvent Raychem HWAT-ECO V4 Manuale utente

nvent

nvent RAYCHEM NGC-40-IO Manuale utente

nvent

nvent Raychem NGC-CMA Manuale utente

nvent

nvent HWAT-ECO-GF Manuale utente

nvent

nvent Raychem HWAT ECO V5 Manuale utente

nvent

nvent RAYCHEM HWAT-ECO-GF Manuale utente

nvent

nvent Raychem Raystat-M2 Manuale utente

nvent

nvent HWAT ECO Manuale utente

nvent

nvent Raychem NGC-30-CR Manuale utente

nvent

nvent RAYCHEM NGC-40-PTM Manuale utente

nvent

nvent ERIFLEX UDJ125A Manuale utente

nvent

nvent ERICO Plus Manuale utente

nvent

nvent Raychem NGC-40-BRIDGE Manuale utente

nvent

nvent Raychem TraceTek TTA-SIM Istruzioni per l'installazione

nvent

nvent Raychem RMM2 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente

nvent Eriflex Flexibar UDF500 Manuale utente

Manuali Unità di controllo popolari di altre marche