Oki Microline 8480 FB Manuale utente

Step 1:

Unpack

Check the Contents

If any items are missing, contact your dealer

immediately.

Printer

Stacker

Power Cable

Ribbon Cartridge

Not illustrated: Documentation

Space Requirements

Place the printer on a stable, level surface.

Check that sufficient space is available for the

installation:

• Width: 35.4" (90 cm)

•Depth

– Behind printer: 23.6" (60 cm)

– In front of printer: 12.6" (32 cm)

– Overall: 60.2" (153 cm)

• Height: 18" (46 cm) minimum

Environmental

Requirements

• Operating Temperature: 41 to 104°F (5 to 40°C)

• Humidity: 30 to 85% RH

Documentation

Your printer includes the following documentation:

•This

Setup Guide

How to get the printer up and running.

•

Safety and Regulatory Information

booklet

Important safety information, along with general

regulatory information (FCC, Energy Star, IC, etc.)

and the Material Safety Data Sheet for the ribbon.

•

User’s Guide

PDF file on the CD included with the

printer

Information on print modes, features such as Forms

Tear-Off and Auto Gap, setting the top of form,

using the control panel, making changes in the

printer defaults, clearing paper jams, etc.

OKI®MICROLINE®8480FB

Setup Guide

Components Feb 17 06.jpg

Printer Components

Front View

Ribbon Cartridge

Platen Knob

Sheet Guide

Power Switch

Sheet Platform

Display Panel

Sheet Supports

Stacker

Printhead

Cover

Control Panel

Rear View

Stacker

Parallel Port

Power Socket

USB Port

Step 2:

Set Up the Printer

Remove the Printhead

Shipping Restraint

1. Open the cover using the grips on either side.

2. Peel the protective plastic film off the display

panel.

3. Tilt the display panel toward you.

F1_24a1.jpg

F1_24b1.jpg

F2_03_open_

cover.jpg

F2_15c.jpg

F2_04_Tilt_

Display.jpg

4. Remove the shipping restraint (

Note

Save the shipping restraint and packing materials

in case you ever need to ship the printer.

5. Push the display panel back to its original

position.

6. Close the cover.

Install the Power Cord

1. Make sure the printer power switch is in the OFF

position:

2. Attach the power cord to the back of the printer.

3. Plug the opposite end into a suitable, grounded

outlet.

Install the Ribbon Cartridge

1. Turn ON the printer.

The printhead lifts, moves to the left, then

moves to the center and stops.

2. Turn OFF the printer

before

opening the cover.

F2_04a.jpg

F2_04_Tilt_Display_

Back.jpg

F2_03_close_c

over.jpg

F2_06.jpg

F2_19.jpg

F2_21.jpg

F2_06a.jpg

Warning!

Make sure the printer is turned off before you

open the cover.

3. Open the cover.

4. Verify that the printhead is centered (at the

“Ribbon set position”).

5. Unpack the ribbon cartridge and remove the lock

pieces (

6. Swing out the ribbon arms on either end of the

cartridge until they

snap

into place.

7. Tilt the display panel toward you.

F2_03_open_c

over.jpg

F2_07a.jpg

F2_09.jpg

F2_10a.jpg

F2_04_Tilt_

Display.jpg

8. Observe the black pin (

) over which the ribbon

knob fits, and the guides (

)—one at either end—

into which the ribbon arms fit.

9. Feed the ribbon arms (

) in beside the guides

(

), position the take-up knob (

) over the pin,

then press the cartridge in firmly at either end.

10. Pull the ribbon out a bit at the left end of the

cartridge to give some slack, then slide the ribbon

underneath the printhead. Be careful that the

ribbon is not twisted, folded or pulled off the

ribbon arms during this process.

11. Make sure the ribbon is threaded through the

indentation in each ribbon guide arm.

Caution!

Always turn the ribbon knob

clockwise

turning it

counter

clockwise (to the left) can

cause the ribbon to jam.

12. Turn the ribbon knob

clockwise

(in the direction

of the molded arrow) to take up any excess slack

in the ribbon.

F2_07b.jpg

F2_11a.jpg

F2_13a.jpg

F2_1

3b.jp

F2_15a.j

13. Push the display panel back to its original

position.

13. Close the cover.

Caution!

If the cover does not close easily,

do not

force it

. The right end of the ribbon

cartridge is not properly seated in the

printer. Open the cover and reseat it. Then

reclose the cover.

Install the Stacker

With the flat edge toward the printer and the frosted

side up, slide the stacker into the channels at either

end of the support, pushing it in as far as it will go.

Remove the Protective Film

Peel the protective plastic film off the viewing area on

the cover.

F2_15b.jpg

F2_03_cl

ose_cove

r.jpg

F2_17_rev.jpg

Remove_Prote

ctive_Plastic.jp

Step 3:

Run a Self Test

Before proceeding, run a self test to check that the

printer is operating correctly. This prints out a list of

available fonts.

1. Turn off the printer.

2. Press and hold MODE and LF while

turning on the printer. Release them

when

RELEASE SW

appears on the

second line of the display.

3. When the printer finishes initializing,

the display will prompt you to insert paper.

4. Place a letter size or larger sheet of paper on the

platform anywhere within the “Paper range when

Auto Align is ON” area.

The sheet feeds in. The first page of the test

prints and the page is ejected back out onto

the platform. The printer display then prompts

you to insert paper.

5. Remove the printed sheet and insert a new sheet.

The sheet feeds in and the remainder of the test

prints. The page is ejected.

The self test is complete.

Step 4:

Load Paper

Individual Sheets/Forms

(“MANUAL”)

The printer is set at the factory for

• single sheets/forms (Manual Feed)

• Auto Align mode

• Normal print mode

• automatic printhead gap (Auto Gap)

Paper Specifications,

for Use with Auto Align Mode

Note

Printing envelopes requires use of the sheet

guide (

) instead of the Auto Align mode. See

your on-line User’s Guide for instructions on

turning off Auto Gap.

Minimum Print Margins

1/4-inch (6.4 mm) on all sides

Individual Sheets

•Size

– Minimum Width: 3.9” (100 mm)

– Maximum Width: 14.3” (364 mm)

– Minimum Length: 2.75” (70 mm)

– Maximum Length: 16.5” (420 mm)

•Weight

– Minimum:13.8 lb. US Bond (52 g/m

)

– Maximum: 55.8 lb. US Bond (210 g/m

)

MODE + LF.jpg

F5-11a.jpg

Individual Multi-Part Forms

•Size

– Minimum Width: 3.9” (100 mm)

– Maximum Width: 14.3” (364 mm)

– Minimum Length: 2.75” (70 mm)

– Maximum Length: 14.3” (364 mm)

•

Normal Print Mode

(the factory default)

– Up to 6-part forms (original + 5)

– Maximum Thickness: 0.0142” (0.36 mm)

• High Impact Mode

– Up to 8-part forms (original + 7)

– Maximum Thickness: 0.0189” (0.48 mm)

Switching Between Normal and

High Impact Mode

Normal to High Impact

Press MODE/HIGH IMPACT.

The LED beside HIGH IMPACT comes

on and H-IMPCT appears at the end of

the first line of the display.

High Impact to Normal

Press LF/NORMAL PRIN.

The LED beside HIGH IMPACT goes out

and NORMAL appears at the end of

the first line of the display.

Load Individual Sheets/Forms

1. Pull out the sheet supports (

) and move the

sheet guide (

) to the right as far as it will go (the

travel of the sheet guide is limited).

2. Place a letter size or larger sheet/form on the

platform anywhere within the “Paper range when

Auto Align is ON” area

The sheet loads in to the print position,

automatically aligning so that it is square with the

print path.

MODE.jpg

LF.jpg

Sheet_G

uide_cro

p.jpg

F5-11a.jpg

Continuous Forms

(“FRONT”)

Continuous Forms Specifications

•Width

– Minimum: 4” (102 mm)

– Maximum: 16” (406 mm)

• Single Thickness Forms

–Weight range: 13.8 to 34 lb. US Bond

(52 to 128 g/m

)

•

Multi-part Forms: Normal Print Mode

(the printer default)

– up to 6-part forms (original + 5)

– Maximum Thickness: 0.0142” (0.36 mm)

• Multi-part Forms: High Impact Mode

– up to 8-part forms (original + 7)

– Maximum Thickness: 0.0189” (0.48 mm)

Note

To switch between Normal and High Impact

mode, see page 8.

Set the Printer for Continuous

Forms

1. If there is a sheet loaded on the platform, remove

it.

2. With the printer turned on, press SEL to place the

printer off line.

3. Press MODE once or rwice until you see

FRONT

on the second line of the display.

The printer will change paths and return to the

on line state. FRONT appears on the second

line of the display.

Note

To switch back to single sheet feed, follow the

same steps, pressing MODE several times until

you see

MANUAL

on the second line of the

display.

Load Continuous Forms

1. Push the sheet supports in and lift the sheet feed

platform

2. Lift the lock lever on the left tractor, then move

the left tractor to set the desired left margin for

printing.

•The

▼

mark on the gauge (

)—or the center of

the diamond shaped hole (

)—represents the

location of the center of the first character

printed.

Note

The movement of the left tractor is limited to

ensure that the paper covers the paper out

sensor.

3. Push the lock lever down to lock the left tractor in

place.

8480_3_crop.jpg

F5-03a.jpg

8480_2_crop.jpg

F5-04a.jpg

4. Lift the lock lever (

) on the right tractor (

) and

move the tractor over to correspond to the width

of the continuous forms you are using. Center the

paper support (

) between the two tractors.

5. Open both tractor covers and place the first three

holes in the continuous forms paper over the pins.

Important!

Make sure that an equal number of paper holes

are engaged on each tractor. If not, the paper

will jam.

6. Close the tractor covers and fine tune the position

of the right tractor until the holes in the paper are

centered on the pins, then push back the right

tractor lock lever.

7. Lower the platform.

8. Position the continuous forms stack below the

printer with no more than about 1 inch (3 cm)

offset (

Tearing Off Printed Continuous

Forms

1. With the SEL light on, press SHIFT.

The continuous forms move forward onto the

stacker.

2. Tear off the printed form along the perforation.

3. Press SHIFT.

The forms move back into the printer, ready for

printing the next document.

Removing Continuous Forms

1. Follow the steps above to remove the printed

portion.

2. Press SEL.

3. Press LOAD.

The forms move back to the tractors.

4. Lift the platform and remove the forms from the

tractors.

5. Lower the platform.

F5-05a.jpg

F5-06a.jpg

F5-06b.jpg

F5-07a.jpg

F5-08a.jpg

F5-09.jpg

Altri manuali per Microline 8480 FB

Indice

Altri manuali Oki Stampante

Manuali Stampante popolari di altre marche

Lexmark

Lexmark 1400 Series Manuale

Canon

Canon i70 Series Manuale utente

Evolis

Evolis Elypso Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Canon

Canon LASER SHOT LBP-1210 Manuale utente

Samsung

Samsung BIXOLON SRP-350plusF Manuale utente

Canon

Canon PIXMA PRO-1 Series Manuale utente

Canon

Canon PIXMA G3560 Guida all'installazione

Dell

Dell Color Laser Printer 2130cn Manuale utente

Tektronix

Tektronix Phaser 840 Manuale utente

Epson

Epson ET-7750 Istruzioni operative

Canon

Canon CLBR 460ps Manuale utente

Eltron

Eltron P210 Guide Manuale utente

Ricoh

Ricoh MD-P1 Manuale utente

Epson

Epson SC-F7100 series Manuale utente

Epson

Epson Stylus C40UX Manuale utente

Canon

Canon imagePASS-A2 Manuale utente

Canon

Canon S820D Manuale utente