Oki ML3410 Manuale utente

Chapter 1

Manual Front Cover

PACEMARK 3410 Printer Handbook

for Epson/IBM & Microline/Pacemark Models

PN 59249101, PM3410, PACE, PM3FM, 12/91, Final

ML3410 ( 96-02-07 )

Chapter 1

Setup

Unpack your printer and make sure you have the following items:

Pacemark 3410 Printer Platen knob

Power cord Ribbon cartridge

Sheet separator (w/rollers)Bottom tractor unit

Printer Handbook

If you are missing any of these items, contact your dealer.

ML3410 ( 96-02-07 )

Preliminaries

After unpacking the printer, there are a few minor tasks that must be performed

ML3410 ( 96-02-07 )

Remove shipping restraint

After unpacking the printer, there are a few minor tasks that must be performed before you can

begin.

1. Open the front cover of the printer.

2. Remove the shipping restraint located under the printhead.

3. Open the rear cover. Set the pull-up roller on the printer so that the tabs on the roller are in the

grooves in the printer.

Save the shipping restraint and the packing material for reshipping.

ML3410 ( 96-02-07 )

Installing the Platen Knob

You will notice that the shaft on the platen knob has a flat side that matches the flat side of the shaft

in the printer.

1. Line up the flat side of the platen knob shaft with the flat side of the printer shaft.

2. Push the knob into place.

ML3410 ( 96-02-07 )

Inserting the Ribbon

1. Unpack the ribbon and remove the shipping restraint.

2. Push the idler roller latch in.

3. Lay the ribbon in the printer so that the pins on the cartridge fit into the notches in the side plates

of the printer. Push down on the cartridge until it clicks into place (See the diagram on the

cartridge).

Note

Turn the knob in the direction of the arrow if the cartridge doesn't fit into place easily.

4. Center the printhead.

5. Thread the ribbon around the posts as shown.

6. Turn the take-up knob clockwise to take up the slack in the ribbon.

ML3410 ( 96-02-07 )

The Bottom Feed Tractor Unit

This separate unit makes it easy and convenient for you to use continuous forms paper fed from the

bottom of the printer.

To install the bottom feed unit:

1. Place the unit where you plan to put the printer. The opening in the unit should face the same

direction as the front of the printer.

2. Pick up the printer and put it on top of the bottom feed unit as shown. Be sure the printer is firmly

seated on the unit.

3. Plug the cable on the unit into the round socket above the parallel interface connector on the

back of the printer. The arrow on the plug faces up.

Caution

Do not attempt to pick up the printer and bottom feed unit together. Disconnect the printer from

the bottom feed unit

and move them separately.

ML3410 ( 96-02-07 )

Making Connections

The power cable and the interface cable have to be connected before you can use your printer. Before

you begin, make sure that the power switch is off.

Plug the power cord into the printer, but do not plug it into an electrical outlet until setup is complete.

ML3410 ( 96-02-07 )

Choosing Parallel or Serial

Your Pacemark 3410 has both a parallel and a serial port. All you have to do is decide which one

you want to use. You can only use one of them at a time.

When you take the printer out of the box, there will be a metal plate over the serial port. If you want

to use the parallel port, just plug in your cable and fasten the clips to it.

If you want to use the serial interface, loosen the metal plate with a Phillips screwdriver and slide it

to the right to uncover the serial port. Plug your cable into the serial port and tighten the screws.

You can fasten the metal plate over the parallel port to eliminate confusion in the future.

You can fasten the metal plate over the parallel port to eliminate confusion in the future. If you use the

serial port, you may have to enter the Menu Select mode and adjust the menu settings. See Chapter 3 (

) for an explanation of the Menu Select mode.

ML3410 ( 96-02-07 )

Adjusting the HeadGap

The headgapis the distance between the printhead andthe roller. When you use envelopes or multi-part

forms, you want to have a larger head gap than when you use plain paper. Use the recommended head

gap to ensure the best print quality and easy paper feeding.

To adjust the head gap, open the front cover. The blue head gap lever is located on the right side of the

printer. Use the following chart to determine the proper head gap for your needs.

Paper Setting

12-24 lb. paper 1

Labels 3-4

Envelopes 5-9

Forms (w/carbon)

Two-part 2-3

Three-part 3-4

Four-part 5

Five-part 6

Six-part 7

ML3410 ( 96-02-07 )

Questo manuale è adatto per i seguenti modelli

Indice

Manuali Stampante popolari di altre marche

Lexmark

Lexmark 1400 Series Manuale

Canon

Canon i70 Series Manuale utente

Evolis

Evolis Elypso Manuale utente

Kyocera

Kyocera FS-9530DN Manuale utente

Canon

Canon LASER SHOT LBP-1210 Manuale utente

Samsung

Samsung BIXOLON SRP-350plusF Manuale utente

Canon

Canon PIXMA PRO-1 Series Manuale utente

Canon

Canon PIXMA G3560 Guida all'installazione

Dell

Dell Color Laser Printer 2130cn Manuale utente

Tektronix

Tektronix Phaser 840 Manuale utente

Epson

Epson ET-7750 Istruzioni operative

Canon

Canon CLBR 460ps Manuale utente

Eltron

Eltron P210 Guide Manuale utente

Ricoh

Ricoh MD-P1 Manuale utente

Epson

Epson SC-F7100 series Manuale utente

Epson

Epson Stylus C40UX Manuale utente

Canon

Canon imagePASS-A2 Manuale utente

Canon

Canon S820D Manuale utente