OLIMEX MOD-ZIGBEE Manuale utente

MOD-ZIGBEE development board

Users Manual

All boards produced by Olimex are ROHS compliant

Rev. B, March 2 13

Page 1 of 17

INTRODUCTION

MOD- IGBEE features a bundle of 8bit PIC18 processor and an 802.15.4

compatible radio module that makes it easy to develop applications based on RF

communication and especially igBee based protocol stacks. In addition MOD-

IGBEE implements an on-board digital temperature sensor, for remote

temperature reporting.

BOARD FEATURES

•CPU: PIC18F26K20

•RF Transceiver – MRF24J40 IEEE 802.15.4™ standard compliant 2.4

GHz RF transceiver

•ICSP connector

•On-board antenna

•On-board temperature sensor – TCN75A

•Option for external power supply through EXT_PWR

•EXT/BAT switch

•Reset circuit

•two user buttons

•two status LEDs

•RST button

•+3V lithium battery holder

•PCB: FR-4, 1.00 mm (0,039"), solder mask, silkscreen component print

•Dimensions: 65.15x20.38 mm (2.56x0.80")

ELECTROSTATIC WARNING

The MOD- IGBEE board is shipped in protective anti-static packaging. The board

must not be subject to high electrostatic potentials. General practice for working

with static sensitive devices should be applied when working with this board.

BOARD USE REQUIREMENTS

Cables: The cable you will need depends on the programmer/debugger you

use. If you use PIC-ICD2-POCKET or PIC-Kit3 you will need 1.8 m A-

B USB cable.

Hardware: One of Olimex programmers/debuggers – PIC-ICD2-POCKET, PIC-

KIT3, or other compatible programming/debugging tool. Also

note that you would need adapter for the small ICSP connector (0.05''

step) - PIC-ICSP

Software: MPLAB IDE

Page 2 of 17

PROCESSOR FEATURES

MOD-ZIGBEE use 28-pin Flash Microcontroller with nano Watt XLP Technology –

PIC18F26K20, with these features:

−High-Performance RISC CPU:

−C Compiler Optimized Architecture:

−Optional extended instruction set designed to optimize re-

entrant code

−1024 bytes Data EEPROM

−64 Kbytes Linear Program Memory Addressing

−3936 bytes Linear Data Memory Addressing

−Up to 16 MIPS Operation

−16-bit Wide Instructions, 8-bit Wide Data Path

−Priority Levels for Interrupts

−31-Level, Software Accessible Hardware Stack

−8 x 8 Single-Cycle Hardware Multiplier

−Flexible Oscillator Structure:

−Precision 16 MHz Internal Oscillator Block:

−Factory calibrated to ± 1%

−Software selectable frequencies range of 31 kHz to 16 MHz

−64 MHz performance available using PLL – no external

components required

−Four Crystal modes up to 64 MHz

−Two External Clock modes up to 64 MHz

−4X Phase Lock Loop (PLL)

−Secondary Oscillator using Timer1 @ 32 kHz

−Fail-Safe Clock Monitor:

−Allows for safe shutdown if peripheral clock stops

−Two-Speed Oscillator Start-up

−Special Microcontroller Features:

−Operating Voltage Range: 1.8V to 3.6V

−Self-Programmable under Software Control

−Programmable 16-Level High/Low-Voltage Detection (HLVD)

module:

−Interrupt on High/Low-Voltage Detection

−Programmable Brown-out Reset (BOR):

−With software enable option

−Extended Watchdog Timer (WDT):

Page 3 of 17

−Programmable period from 4 ms to 131s

−Single-Supply 3V In-Circuit Serial Programming™ (ICSP™) via Two

Pins

−In-Circuit Debug (ICD) via Two Pins

−Extreme Low-Power Management with nanoWatt XLP:

−Sleep mode: < 100 nA @ 1.8V

−Watchdog Timer: < 800 nA @ 1.8V

−Timer1 Oscillator: < 800 nA @ 32 kHz and 1.8V

−Analog Features:

−Analog-to-Digital Converter (ADC) module:

−10-bit, 10 Channels

−Auto-acquisition capability

−Conversion available during Sleep

−One 1.2V Fixed Voltage Reference (FVR) channel

−Independent input multiplexing

−Analog Comparator module:

−Two rail-to-rail analog comparators

−Independent input multiplexing

−Voltage Reference (CVREF) module

−Programmable (% VDD), 16 steps

−Two 16-level voltage ranges using VREF pins

−Peripheral Highlights:

−24 I/O Pins plus 1 Input-only Pin:

−High-Current Sink/Source 25 mA/25 mA

−Three programmable external interrupts

−Four programmable interrupt-on-change

−Eight programmable weak pull-ups

−Programmable slew rate

−Master Synchronous Serial Port (MSSP) module

−3-wire SPI

−I2C™ Master and Slave modes with address mask

−Enhanced Universal Synchronous Asynchronous Receiver

Transmitter (EUSART) module:

−Supports RS-485, RS-232 and LIN

−RS-232 operation using internal oscillator

−Auto-Wake-up on Break

−Auto-Baud Detect

Page 4 of 17

BLOCK DIAGRAM

Page 5 of 17

MEMORY MAP

Page 6 of 17

RF TRANSCEIVER FEATURES

−IEEE 802.15.4™ Standard Compliant RF Transceiver

−Supports igBee®, MiWi™, MiWi P2P and Proprietary Wireless Networking

Protocols

−Simple, 4-Wire SPI Interface

−Integrated 20 MHz and 32.768 kHz Crystal Oscillator Circuitry

−Low-Current Consumption:

−RX mode: 19 mA (typical)

−TX mode: 23 mA (typical)

−Sleep: 2 μA (typical)

−RF/Analog Features:

−ISM Band 2.405-2.48 GHz Operation

−Data Rate: 250 kbps (IEEE 802.15.4); 625 kbps (Turbo mode)

−-95 dBm Typical Sensitivity with +5 dBm Maximum Input Level

−+0 dBm Typical Output Power with 36 dB TX Power Control Range

−Differential RF Input/Output with Integrated TX/RX Switch

−Integrated Low Phase Noise VCO, Frequency Synthesizer and PLL

Loop Filter

−Digital VCO and Filter Calibration

−Integrated RSSI ADC and I/Q DACs

−Integrated LDO

−High Receiver and RSSI Dynamic Range

−MAC/Baseband Features:

−Hardware CSMA-CA Mechanism, Automatic Acknowledgement

Response and FCS Check

−Independent Beacon, Transmit and GTS FIFO

−Supports all CCA modes and RSSI/ED

−Automatic Packet Retransmit Capability

−Hardware Security Engine (AES-128) with CTR, CCM and CBC-MAC

modes

−Supports Encryption and Decryption for MAC Sublayer and Upper

Layer

Page 7 of 17

RF TRANSCEIVER BLOCK DIAGRAM

Page 8 of 17

RF TRANSCEIVER MEMORY MAP

Page 9 of 17

SCHEMATIC

SID E_W TC M -TR(3X4)

SID E_W TC M -TR (3X4)

BTH-V20-LF

0.5pF /50V/ +-0.25pF /COG 0 .5 pF/ 50 V/+-0.25 pF/ COG

N 1p F/5 0V /+-0 .25p F/COG

1pF/50V/+-0.25pF/COG

100pF/50V/+-5%/COG

100n/10V /+ - 10% /X5R

47pF/50V /+ -5% /CO G

100n/10V/+- 10% /X5R

10n/25V /+ - 10%/X7R

47pF/50V /+ -5% /CO G

47pF/50V /+ -5% /COG

10n/25V /+- 10%/X7R

1uF/6.3V /+-20% /X 5R

27pF/50V/+-5%/COG

1000uF/6.3 V/8x12/lo w_ESR

100nF

100nF 100nF

ZD8 .2V/0 .2 W /SMD

SWITCH_IS-1390

WU6S

3.3 nH/+-0.3nH/4 00 m A/12 0. 0m O

6.8 nH/ +-5% /3 20 m A/3 00.0 m O

8.2 nH/+-5% /3 20 m A/ 350.0 m O 5.6n H/+-0. 3n H/3 40 m A/ 19 0.0m O

red green

20.0000MHz/18pF/5x3.2

10k

330R

10k 10K 10K

10K 10K 560R 560R

330R 330R

330R

IT1185AU2

MRF24J40-I/M

IC18F26K20-I/SS

TCN75AVUA

3V 3V

3V3

IDC10S- CB

#SS

LED1

LED2

MISO

MOSI

RF_CS

RF_INT

RF_RST

RF_WAKE

RST

RST RST_ICS

RST_ICS

RXD

SCK

SCL

SDA

TEM _INT

TXD

B1 B2

BAT

C1 C2

C3 C4

C10

C11

C12

C13

C14

C15

C1 6

C17

C18

C19

C20

C21

C22

C23 C24

EXT_BAT

EXT_ WR

GND

ICS

L3 L 4

LED1 LED2

CB_ANT

GND

GND_

R3 R4 R5

R6 R7 R8 R9

R10 R11

R12

RA1

RA2

RA3

RB1

RB2

RST

CS 20

GND

G IO0 7

G IO1 8

G IO2 11

G IO3 12

G IO4 10

G IO5 9

INT 16

LCA 40

L OSC1

28 L OSC2

27 NC 23

NC 26

NC 29

NC 38

NC 30

OSC1

34 OSC2

RESET

RFN 3

RF 2

SCK 19

SDI 18

SDO 17

VDD

WAKE 15

AN12/FLT0/INT0/RB0 21

CC 2/C12IN2-/AN9/RB3 24

CK/TX/RC6 17

DT/RX/RC7 18

MCLR#/V /RE3

OSC1/CLKIN/RA7

OSC2/CLKOUT/RA6

1B/AN8/INT2/RB2 23

1C/C12IN3-/AN10/INT1/RB1 22

1D/AN11/KBI0/RB4 25

GC/KBI2/RB6 27

GD/KBI3/RB7 28

GM/KBI1/RB5 26

RA0/AN0/C12IN0

RA1/AN1/C12IN1

RA2/AN2/VREF-/CVREF/C2IN+

RA3/AN3/VREF+/C1IN+

RA4/T0CKI/C1OUT

RA5/AN4/SS#/HLVDIN/C2OUT

RC0/T1OSO/T13CKI

RC1/T1OSI/CC 2

RC2/CC 1/ 1A

RC3/SCK/SCL

14 SDA/SDI/RC4 15

SDO/RC5 16

VDD

VSS

A0 7

A1 6

A2 5

ALERT

GND

SCL

2SDA

1VDD 8

(#OS /INT )

1 2

3 4

5 6

7 8

9 10

UEXT

MOD-ZIGBEE_rev_C

OLIMEX LTD, BULGARIA

https://www.olimex.com

RESET CIRCUIT

UEXTICSBUTTONS&LEDS

I2C SENSOR

RADIO MODULE

2.4V-3.6V

Indice

Altri manuali OLIMEX Scheda madre

OLIMEX

OLIMEX AVR-T32U4 Manuale utente

OLIMEX

OLIMEX STM32-P107 Manuale utente

OLIMEX

OLIMEX LPC-P11C24 Manuale utente

OLIMEX

OLIMEX MOD-RTC Manuale utente

OLIMEX

OLIMEX MOD-MP3-X Manuale utente

OLIMEX

OLIMEX PIC32-EMZ64 Manuale utente

OLIMEX

OLIMEX MOD-VGA Manuale utente

OLIMEX

OLIMEX iMX233-OLinuXino-NANO Manuale utente

OLIMEX

OLIMEX PIC-MICRO-WEB Manuale utente

OLIMEX

OLIMEX AVR-ISP500-TINY Manuale utente

OLIMEX

OLIMEX PIC-P40-USB Manuale utente

OLIMEX

OLIMEX OLinuXino-MAXI Manuale utente

OLIMEX

OLIMEX STM32-H405 Manuale utente

OLIMEX

OLIMEX A10-OLINUXINO-LIME Manuale utente

OLIMEX

OLIMEX MOD-SD MMC Manuale utente

OLIMEX

OLIMEX OLIMEXINO-STM32 Manuale utente

OLIMEX

OLIMEX PIC32-MAXI-WEB Manuale utente

OLIMEX

OLIMEX STM32-P107 Manuale utente

OLIMEX

OLIMEX OLIMEXINO-32U4 Manuale utente

OLIMEX

OLIMEX MSP430-CCRF Manuale utente

OLIMEX

OLIMEX MOD-VGA Manuale utente

OLIMEX

OLIMEX STM32-E407 Manuale utente

OLIMEX

OLIMEX OLinuXino-MAXI Manuale utente

OLIMEX

OLIMEX MOD-SD MMC Manuale utente

Manuali Scheda madre popolari di altre marche

DFI

DFI SD170 Manuale utente

ASROCK

ASROCK ROMED8-2T Manuale utente

Asus

Asus P2L97A Manuale utente

Winmate

Winmate IC70 Manuale utente

Asus

Asus MES-B Manuale utente

Grantech

Grantech SYS8F377VGGA-3OMN Manuale utente

Telit Wireless Solutions

Telit Wireless Solutions SL869-3DR Manuale utente

Gigabyte

Gigabyte GA-9IVDT Manuale utente

Texas Instruments

Texas Instruments ADS8372EVM Manuale utente

Commell

Commell MS-C73 Manuale utente

IBT Technologies

IBT Technologies MB860 Manuale utente

Nvidia

Nvidia TEGRA DG-04927-001_V01 Manuale utente

Biostar

Biostar M7VIT Bravo Istruzioni per l'uso e l'installazione

Intel

Intel D33217CK Manuale utente

Asus

Asus F1A55-M LX PLUS R2.0 Manuale utente

EPC

EPC EPC9147C Manuale utente

Asus

Asus EX-B760M-V5 D4 Manuale utente

EPOX

EPOX MU-8KHA0010 Manuale utente