Oneida Air Systems Vortex DCS Manuale utente

“I gotta say, that’s an impressive machine.”

Norm Abram

This Old House

Episode #2615

Sander

Not Included

The most effective portable oor sanding dust containment system

with patented vortex technology.

Vortex Gorilla Vac

Dust Containment System

Oneida Vortex DCS

Dust Containment Systems

Keep the Job Clean! 12_13

Owner’s Manual

Collect Dust

at the

Source!

OAS Vortex DCS Owner’s Manual O.A.S. 2013

! !

Caution: Read Before Operating

Wood Dust is Highly Flammable!

Always locate dust bin in a safe area, preferably outdoors. Keep a 10’ distance from dust bin when

sander is in operation.

Static electricity can ignite a re or injure personnel.

Wood dust can are up if ignited.

Make sure system is plugged into a grounded circuit.

Never introduce sparks or ame into the system.

- Drive down nail heads to prevent sparks.

- Never sand ferrous materials.

This collector is designed for wood waste ONLY.

Never use collector for materials other than wood products.

Store wood waste in a safe area outside.

Don’t leave jobsite without properly disposing of waste to a safe area. Smoldering dust can ignite later.

Clean debris off oor before sanding. Debris can clog system.

Clean both lter cartridges at regular intervals. Vacuum out the lter pleats from the inside of the lter

or blow off from the outside. See cleaning procedure on pg. 6.

Do not overll Dust Bin. Check regularly.

Do not operate collector in ammable atmosphere. (i.e. - Finish fumes)

Caution: Fine dust is the most hazardous to breathe and very ammable.

Wood Dust Can Be Hazardous to Your Health!

The Federal government has declared that wood dust is a known human carcinogen. Different woods also have

different levels of irritation, some worse than others, especially with the increased use of exotic woods in ooring.

What you also may not know is that before 1978, lead was used in many varnishes. When you sand this varnish,

the dust concentrates the lead and makes the wood dust even more toxic. Asbestos exposure can occur when you

are dealing with old adhesives and vinyl tiles.

The best way to deal with this toxic cloud is to collect the wood dust at the source, for you and your customers

safety. Without proper dust collection, workers are exposed on every job and customers are exposed until all dust is

nally cleaned up. Not a good situation for either party.

Always follow all Federal,

State and Local

guidelines and codes.

Collect Dust at the Source!

Congratulations!

You have purchased a state-of-the-art Oneida Vortex DCS Dust Containment

System for oor sanding machines. In order to facilitate your transition to

using our system, makesure all people using the system read the Owner’s

Manual. The information provided is very important to the day-to-day opera-

tion of the dust containment system.

1.800.732.4065

Customer Service or

Technical Questions:

OAS Vortex DCS Owner’s Manual O.A.S. 2013

Assembly:

Cyclone & Filter for Vortex Sander Cyclone

Rotating

Filter

Cleaner

Attach Filter

Cartridge to

top of Cyclone

with Clamps.

Pleated

Filter

Cartridge

Be careful not

to damage lter.

Clamps

Cyclone

Elbow

T - Clamp

Connect Cyclone to

Floor Sander Dust Outlet

with Provided T-Clamp.

Connection should be

air-tight.

Connect Cone outlet to

Flex Hose out to 2nd

Cyclone on dust drum

and Vac Pump.

*Clamp should

be placed so

that the middle

of the clamp

lies on the

seam between

the elbow

and exhaust

stack. Watch

for leaks at

this location.

Tighten clamp

OAS Vortex DCS Owner’s Manual O.A.S. 2013

Sander Cyclones - General Tips

Filter Cleaner

Crank

Spun-Bond

Polyester Filter

Cartridge

Stack Pipe

Clamp w/

Gasket

Clear

Cone

Filter

Latch

8” Clamp

Cyclone

Waste

Outlet

Keep an eye on the Clear Cone during operation. Material should be

swirling and exiting the cone. If material is accumulating in the cone, shut-

down the sander. Remove the hose from the cyclone waste outlet. Make

sure the vacuum is on and all hoses are connected. Remove the Clear

Cone and dump out accumulated dust. Check lter and clean if neces-

sary. Reassemble and you’re ready to sand.

Make sure Stack Pipe Clamp is tightened down so there are no leaks. If it

is too loose you you will see dust around the clamp on the Stack.

When rotating the cyclone on the Sander, turn Sander off, loosen clamp,

rotate and tighten. Rotating while Sander is on will cause a puff of dust to

escape at the clamp.

2 1/2” I.D.

2 5/8” O.D.

Filters - All HEPA Filtration

Filters must be cleaned with compressed air after or before every job. This maintenance

will ensure your dust collector is running efciently. Follow lter cleaning instructions on

pg, 3.

Oneida’s lters are extremely durable and reusable. Their lifespan is normally between 40 - 100 jobs. Regular and thorough

cleaning with compressed air can extend lter life. All lters are a high efciency, spun-bonded, polyester lter media with

a teon-like coating to aid cleaning. These lters have been 3rd party tested to be 99.9% efcient in ltering 0.2 - 2 micron

dust. 1 micron = 0.0000394 inch.

Filter cleaners allow the operator to go a longer period of time between cleaning the lters

with compressed air. Whenever the machine is shut down, changing paper, taking a

break, etc., give the crank a few turns at a few different heights to drop material out of the

lter.

Filters can be washed out with water after being blown out. They should be completely

dry before re-installing.

Filter Cleaner is a hand-operated lter cleaning mecha-

nism that is attached to the lter. When turned, the crank

rotates a teon-like apper inside the lter that hits the

pleats and drops material down to the bottom of the

cyclone. This is a quick way to maintain your lters on the

job and must be done when the Sander is off. It does not

take the place of cleaning lters with compressed air.

OAS Vortex DCS Owner’s Manual O.A.S. 2013

Hoses Caution: Wood dust and air moving through a plastic hose creates static electricity. All hoses provided by

OAS are static dissipating. Use only the hoses provided. Do NOT use hose that is not static dissipating.

Shock hazard or ignition of ammable mixture may result!

Normal Utility Hose:

- A tough elastomer urethane, static dissipating hose reinforced with a vinyl coated spring steel

wire helix and two molded cuffs.

- Available in 1” to 1.5” inner diameters in 1/4” increments. Sold in lengths of 35’.

- Can effectively be cut and attached with expanding or reducing cuff.

Normal Utility Stretch Hose:

- A vinyl and urethane static dissipating hose with a vinyl coated wire helix that has a 4:1 stretch

ratio and comes with two molded cuffs. Hose retracts with movement of sander.

- A 20’ compressed hose expands to 80’. Only available in 20’ - 80’ lengths.

- This hose can NOT be effectively cut and attached with a new cuff.

Hoses will take on the color of the wood sanded due to a light coating of dust on the inside of the hose.

If you experience a clog in the hose, reverse the ow of air through the hose by hooking the other end up to the vacuum. If

this doesn’t work, blow one end out with compressed air outside. If it still persists, work the clogged dust from the outside

with your hands or bang gently on the ground with the vacuum on.

Hoses should be periodically inspected for leaks in the length and at the end cuffs.

- Hose Sizes for Equipment

Before starting job, make sure lters have been thoroughly cleaned with compressed air.

Equipment Sand Paper Hose Size Comments

Drum Sander

Edger

Palm Sander

Buffers

Vacuum Floor

with Brush

11 - 36 Grit

36 - 150 Grit

1 1/2”

35 - 70 ft.

All Grits

All Screens

1” - 1 1/2”

70 ft.

1 1/2”

70 ft.

1 1/4” or 1 1/2”

35 - 70 ft.

1 1/2”

Very aggressive sanding. Drum sanding with coarse grit. Soft woods or

stripping varnish.

- Pine & Fur - 1 1/2” dia. hose.

Clarke edgers need 1 1/4” or 1 1/2” hose for proper dust collection.

Smaller hoses will clog with debris.

*Note: Pull Flex Hose out of coiled positions avoiding tight and unnecessary loops and bends. Material will ow more easily.

*Note: Use only the amount of hose that is necessary to do the job. Extended lengths will impair waste pick-up at cyclone. Shorter lengths

will improve waste removal at cyclone, especially for aggressive sanding.

OAS Vortex DCS Owner’s Manual 2013

Filter Cleaning Instructions

Filters must be cleaned before or after every

job! This is VERY important! System will not

work unless lters are clean!

Best Way

to Clean

Filters.

At least 3” away

Turn crank up and

down lter.

Blow off

lter from

outside with

compressed

air while Vac

pump is ON

and Sander is

OFF.

OAS Vortex DCS Owner’s Manual O.A.S. 2013

Cyclone Box Should Contain

All of the Items to the Left.

Weight: 20 lbs.

18” x 16” x 14”

Parts List for Vac System Kits

1. Sander Cyclone Barrel Assembly - VXCSXZ000

2. HEPA Filter - Sander - Assembly with Cleaner - VSFSHC000

2a. Sander HEPA Filter 15.3 Sq. Ft. - VSFSHZ000

2b. Filter Cleaner Assembly - VSFCSZ000

3. Clamp 8” Dia. & Pin - VRR080000

4. Sander Cyclone Cone Assembly - VRS080111

4a. Clear Cone - VRS080110

4b. Metal Base for Clear Cone - VXS080110

5. Pipe Clamp 2.5” Regular (Standard) - VSACPZ250

6. Heavy Duty Pipe Coupler 2.5” (optional) - VSACPH250

Sander HEPA Cyclone Kit - VSKCSZ000

1. Sander Cyclone HEPA Filter with Cleaner Assembly - VSFSHC000

2. Sander Cyclone / Vac Pump HEPA Filter - VSFSHZ000

3. Edger HEPA Filter with Cleaner Assembly - VSFEHC000

4. Edger HEPA Filter - VSFEHZ000

HEPA Filters - Gore lter media rated to capture

99.97% down to 0.3 microns

1. Sander Cyclone Filter with Cleaner Assembly - VSFSSC000

2. Sander Cyclone / Vac Pump Filter - VSFSSZ000

3. Edger Filter with Cleaner Assembly - VSFESC000

4. Edger Filter - VSFESZ000

Filters - Non-HEPA Spun-Bond Polyester

Vac Retrot Adaptors

5”

Essex Silverline

Pro 8

Taurus

Handle

Hummel

Handle

Clarke EZ8 Bona Universal

Stack

Bona Pro Sand 8 Super Bee

*Refer to installation sheets for retrot instructions.

VSRSES000 VSRSKT000 VSRSLH000 VSRSEZ000 VSRSBU000 VSRSBP080

Includes

2 1/8” Tube Clamp

VRC002125

VSRSCU000

Includes

2 1/8” Tube Clamp

VRC002125

Galaxy 2000

VXA025020

Need 2.5” clamp

Part # VSACPH250

Only needed

if sander dust

outlet is under

2.5” O.D.

Lagler Trio Retrot Kit

VSRSLT000

Includes:

VXA040000 - Lagler Trio Retrot

VSACPH250 - 2.5” Clamp

Indice

Altri manuali Oneida Air Systems Collettore di polvere

Oneida Air Systems

Oneida Air Systems Gorilla XXP999901 Manuale utente

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD001004 Manuale utente

Oneida Air Systems

Oneida Air Systems Mini-Gorilla Manuale utente

Oneida Air Systems

Oneida Air Systems V1500 Manuale utente

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Manuale utente

Oneida Air Systems

Oneida Air Systems 3H Manuale utente

Oneida Air Systems

Oneida Air Systems 2 HP Commercial Cyclonic Dust Collector Manuale utente

Oneida Air Systems

Oneida Air Systems Supercell XSK000035 Manuale utente

Oneida Air Systems

Oneida Air Systems Supercell Mobile Manuale utente

Oneida Air Systems

Oneida Air Systems BenchTop Manuale utente

Oneida Air Systems

Oneida Air Systems Dust Gorilla Portable XXP990201H Manuale utente

Oneida Air Systems

Oneida Air Systems V-System XXVS300035 Manuale utente

Oneida Air Systems

Oneida Air Systems XGK030035 Manuale utente

Oneida Air Systems

Oneida Air Systems XCKM010000 Manuale utente

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla Manuale utente

Oneida Air Systems

Oneida Air Systems Pro 1500 Manuale utente

Oneida Air Systems

Oneida Air Systems 8491685 Manuale utente

Oneida Air Systems

Oneida Air Systems Smart Pro XXS200001 Manuale utente

Oneida Air Systems

Oneida Air Systems Dust Deputy AXD000004 Manuale utente

Oneida Air Systems

Oneida Air Systems BenchTop DC Manuale utente

Oneida Air Systems

Oneida Air Systems Super Dust Gorilla 2hp Manuale utente

Oneida Air Systems

Oneida Air Systems Dust Gorilla Pro Manuale utente

Oneida Air Systems

Oneida Air Systems Supercell Mobile Manuale utente

Oneida Air Systems

Oneida Air Systems 2005c3HP Manuale utente

Manuali Collettore di polvere popolari di altre marche

Fein

Fein 9-88-35 Manuale utente

Blastrac

Blastrac BDC-44 Manuale utente

DIVERSITECH

DIVERSITECH WB-4000-D Manuale

National

National 3402 Manuale utente

Grizzly

Grizzly G0850 Manuale utente

Bosch

Bosch GDE18V-16 Istruzioni per il montaggio

Grizzly

Grizzly G0441HEP Manuale utente

Storch

Storch Cover Quick Wall Manuale utente

laguna

laguna C FLUX 1 Manuale utente

Jet

Jet DC-1100VX Series Manuale di servizio

GMC

GMC RDC8LA Manuale utente

Showa

Showa Fumeresa CBA-1000AT-HC-DSA-V1 Manuale utente

King Industrial

King Industrial KC-4043KWRC Manuale utente

Jet

Jet 500 Manuale utente

Shop fox

Shop fox SHOP FOX W1687 Manuale utente

Blastrac

Blastrac 655DC Manuale utente

Elektra Beckum

Elektra Beckum Multi 180A Manuale utente

Grizzly

Grizzly G0508 Guida rapida