Optex OVS-6000 Manuale utente
Select a sensor mounting location based on application (Notication or Dwell Time)
OPTEX OVS-6000 Quick Setup Guide
For detailed information, please refer to the installation manual supplied with each sensor.
or
Note: Mount to the side if you don’t have vehicle clearance of the sensor (see above right); ensure vehicles will not strike the sensor.
The OVS-6000 utilizes an active infrared transmitter and photoelectric
receiver located in the rectangular sensor head. This Quick Setup Guide
will answer the most common installation questions, including: Mounting
location, aiming the sensor head to achieve proper detection, self-learning,
and programming.
After choosing the mounting location, open the box and remove
the sensor.
View the Transmitter, Receiver and Dipswitches. See below for detail of
dipswitch settings.
Notication (detecting the approach of a vehicle) applications, vehicle clearance validation
Dwell Time (detecting the presence of a stopped vehicle) applications, vehicle clearance validation
1
2
3
4
sensor 3-4’ sensor 3- 4’
or
sensor 3 - 4’ sensor 3 - 4’
Note that the dipswitches are located behind the black cover, which
can be easily removed by pulling the cover forward.
5
(over)
* Aim detector beams in front of tube machine
Note: Mount to the side if you don’t have vehicle clearance of the sensor (see above right); ensure vehicles will not strike the sensor.
18730 Wilmington Ave, Unit 100
Rancho Dominguez, CA 90220
Ph 310 214-8644
Fax 310 898-1098
Toll free 800 877-6656
www.optex-america.com
OPTEX Technologies Inc.
(East Coast Ofce)
8510 McAlpine Park Dr.
Suite 108
Charlotte, NC 28211
Choose Sensor Settings
Test and Complete Installation
3 and 4 - Frequency
Set 3 and 4 Down (unless using 2 or more detectors with overlapping detec-
tion patterns next to each other; then, adjust to different frequencies).
8 - Delay
8 Down (shown), Notication (Vehicle Approaching): no delay.
8 Up requires 2 or more beams broken within a 3-second period for Dwell
time (Vehicle Stationary).
7 - LED Indicator
7 Down (shown), LED on, turns off with detection.
7 Up, LED stays on with power.
1 and 2 - Presence (Vehicle) Detection Timer
Notication (Vehicle Approaching): 1 and 2 Down (shown).
Dwell Time (Vehicle Stationary): 1 Up, 2 Down
5 and 6 - Adjust Detection Height Area
9 to 15 feet: 5 Up, 6 Down (shown).
12 to 24 feet: 5 Down, 6 Up.
Mount Sensor and Adjust the Detection Pattern
* Apply power - no vehicles in the detection pattern for a 10-second learning time.
When mounted on the ceiling, the sensor head is aimed in this direction.
Loosen keeper nut and adjust sensor head so that it aims at the ground
above the driver’s side of the vehicle.
The sensor projects narrow detection beams towards the ground.
The detection area contains 4 beams, as displayed in image at
right. The IR Locator (optional) will give you the ability to locate the
individual beams. When the LEDs light up on the IR Locator, you
are within the beam area. The IR Locator Adjustment Tool can be
purchased from OPTEX. Call 800-877-6656 to learn more.
IR Locator (optional)
6
7
Indice
Altri manuali Optex Sensore di sicurezza
Optex
Optex FlipX Series Manuale utente
Optex
Optex OVS-01CC Manuale utente
Optex
Optex FASTUS CD22-15 Series Manuale utente
Optex
Optex REDWALL-V Guida
Optex
Optex inSight INS-HX-80N Manuale utente
Optex
Optex Fit Series Manuale utente
Optex
Optex WX Shield Series Manuale utente
Optex
Optex AX-100TFR Series Manuale utente
Optex
Optex X-ZONE Manuale utente
Optex
Optex AX-70TN Manuale utente
Optex
Optex FMX-ST Manuale utente
Optex
Optex WXI-R Manuale utente
Optex
Optex REACTION TWO Manuale utente
Optex
Optex RXC-DT-X5 Manuale utente
Optex
Optex HX-80NRAM Manuale utente
Optex
Optex VX-402R Manuale utente
Optex
Optex inSight INS-HX-80N Manuale utente
Optex
Optex WNX-40HW Manuale utente
Optex
Optex VX SHIELD Series Manuale utente
Optex
Optex AP-360B Manuale utente
