Overland Storage SnapServer XSR 120 Manuale utente
10400577-001 ©2014 Overland Storage, Inc. Page 1 of 4
*10400577001*
SnapServer XSR 120™
Add-on/Spare PCIe Card Instructions
This document describes how to add or replace a PCIe card in a
SnapServer XSR 120 from Overland Storage.
WARNING: To reduce the risk of electric shock or damage to
equipment, always remove any power cords while working
with the unit.
WARNUNG: Um das Risiko eines elektrischen Schlags oder
Schäden am Gerät zu vermeiden, ziehen Sie stets den
Netzstecker, bevor Sie an der Einheit arbeiten.
AVERTISSEMENT: Pour réduire le risque de choc électrique
ou endommagement de l'équipement, retirez toujours les
cordons électriques en travaillant avec l'appareil.
CAUTION: While working with the unit, observe standard
Electrostatic Discharge (ESD) precautions to prevent damage
to micro-circuitry or static-sensitive devices.
Register Add-on PCIe Card
NOTE: If you are only replacing an existing PCIe card, skip to the
next section, “Prepare the Unit.”
When adding a PCIe card to your server, you must first
register it to activate the warranty. Technical and warranty
support are not available until this is done:
1. Go to the Overland Storage website
(http://www.overlandstorage.com/).
2. Select
Service & Support > My Products
.
3. At the Site Login, enter your e-mail address and
password, and click
GO
.
4. Click the
Manage Products
button.
5. From the Product Selector drop-down list, select the XSR
120 in which you are installing the PCIe card.
6. Click
Add a Component
.
7. Enter the PCIe card information.
8. Click
Save & Exit
.
IMPORTANT: Your warranty certificate will be emailed to you.
Follow the instructions included to complete the process.
Enter
Enter
5325301507-SnapServer XSR 120 s/n: 02
10400577-001 ©2014 Overland Storage, Inc. Page 2 of 4
Add-on/Spare PCIe Card Instructions
Prepare the Unit
Power Off and Disconnect
If the unit is still running, power it down cleanly:
1. Use the Web Management Interface to shut down the
server (Maintenance > Reboot and Shutdown >
Shutdown).
2. When all the LEDs are off, disconnect the power cords.
3. Disconnect the remaining cables from the unit, noting
their locations.
Remove the Front Bezel
1. Carefully take hold of the front bezel and pull it straight
out from the appliance until the magnets release.
2. Set the bezel aside on a secure surface.
Remove the Drives
IMPORTANT: Overland recommends that you remove the disk
drives to reduce the unit’s weight prior to removal.
Remove all the drive carriers, noting from which slot they were
removed. Blank carriers can remain in their bays.
NOTE: Do not remove the disk drives from their carriers. Doing so
voids the drive warranty.
1. Press the release button on the right side of the carrier.
2. Using the built-in handle, pull the carrier out.
3. Number the carrier and set it on a secure surface.
4. Repeat Steps 1–3 for all the remaining drive carriers.
Remove Unit from Rack
WARNING: It is recommended that a mechanical lifter (or at
least two people) be used during rack installation or removal
to prevent injury.
WARNUNG: Um Verletzungen zu vermeiden, empfehlen wir
zur Rack-Installation oder -Deinstallation die Nutzung einer
mechanischen Hebehilfe (oder mindestens zwei Personen).
AVERTISSEMENT: Pour éviter toute blessure il est
recommande qu'un monte-charge (ou deux personnes au
moins) soit utilisé lors de l'installation ou de l'enlèvement du
support.
1. Remove and retain the four screws securing the unit to
the rack.
2. With a lifter positioned in front of the array, release the
rail locks and slide the chassis out onto the lifter.
3. Move the chassis onto a secure surface.
PressPull Handle
1
5
9
2
6
10
3
7
11
4
8
12
Secure Surface
10400577-001 ©2014 Overland Storage, Inc. Page 3 of 4
Add-on/Spare PCIe Card Instructions
Install PCIe Cards
Remove Top Panels
1. Remove and retain the two screws located at the front
edge of the panel.
2. Loosen the two captive screws securing the panel rear.
3. Slide the panel toward the rear about one-half inch
(1.25cm), lift it off, and set aside.
Add a New PCIe Card
NOTE: If you are only replacing an existing PCIe card, skip to the
next section, “Replace a PCIe Card.”
1. Remove and retain the rear slot cover and screw from
an appropriate PCIe card slot.
2. Insert the PCIe card in the slot and seat it properly.
3. Secure it with the retained slot cover screw.
Replace a PCIe Card
1. Remove and retain the slot cover screw of the PCIe card
being replaced.
2. Grasp the PCIe card and carefully pull it straight up and
out of the chassis slot.
Set the PCIe card aside on an ESD-safe surface.
3. Insert the new PCIe card in the same slot and secure it
with the retained slot cover screw.
Reassemble the Unit
Reinstall Top Panel
1. Position the top panel with no more than one-half inch
(1.25cm) extending out over the rear of the unit.
2. Slide the panel forward until it is fully seated.
3. Using the two captive screws, secure the panel rear.
4. Using the two retained screws, secure the panel front.
Return Chassis to Rack
1. Slide out the middle rails from the rack.
2. Using the mechanical lifter, position the chassis in front
of the rack.
3. Insert the inner rails into the middle rails and slide the
unit into the rack.
4. Using the four retained screws, secure the SnapServer
to the front of the rack.
Rear
Front Screws
Captive
Screws
Screw
Screw
Rear
Front Screws
Captive
Screws
10400577-001 ©2014 Overland Storage, Inc. Page 4 of 4
http://support.overlandstorage.com
You can get additional technical support on the Internet at the Overland Storage Support web page, or by contacting Overland Storage using
the information found on the Contact Us page on our web site.
Add-on/Spare PCIe Card Instructions
Reinstall Drives
Return the drive carriers to the same drive bays:
1. Referring to the numbering, position a drive assembly in
front of its empty bay in the new chassis.
2. Slide the assembly in until the latch clicks, securing it.
3. Repeat Steps 1–2 for all remaining drive carriers.
IMPORTANT: To maintain proper airflow and cooling, a drive
assembly or a blank carrier must be installed in every bay. No
empty bays are allowed.
Reattach Cables and Power Cords
1. Reattach all cables to the same connections as before.
2. Attach the power cords.
3. At the front of the unit, press the power switch for less
than a second to power the unit ON.
Reattach the Bezel
1. Position the bezel with the tabs aligned inside the top
and bottom edges of the chassis.
2. Move bezel toward the unit until the magnets connect.
3. Verify that the bezel is aligned properly, all the LEDs are
visible, and the Power panel is centered in the left flange.
Return Replaced Parts to Overland
1. Place the replaced part in the anti-static bag and put it
in the replacement part’s box.
2. Use an RMA to return the part to Overland Storage.
For return shipping details and RMA number, go to:
http://docs.overlandstorage.com/return-instructions
Push In Using Handle
Power Sockets Cable Ports
Magnets Tabs
Altri manuali per SnapServer XSR 120
5
Indice
Altri manuali Overland Storage Magazzinaggio
Overland Storage
Overland Storage SnapScale X4 Node Guida
Overland Storage
Overland Storage NEOxl 40 Manuale utente
Overland Storage
Overland Storage SnapServer Manuale utente
Overland Storage
Overland Storage NEO 8000E Manuale utente
Overland Storage
Overland Storage NEO 8000 Manuale utente
Overland Storage
Overland Storage SnapSAN S2000 Manuale utente
Overland Storage
Overland Storage SnapServer DX2 Manuale utente
Overland Storage
Overland Storage SnapServer XSD 40 Manuale utente
Overland Storage
Overland Storage REO 9000 Manuale utente
Overland Storage
Overland Storage SnapServer XSD 40 Manuale utente
Overland Storage
Overland Storage NEO 8000 Manuale utente
Overland Storage
Overland Storage XchangeNOW ARCvault Series Manuale utente
Overland Storage
Overland Storage REO 9000 Manuale utente
Overland Storage
Overland Storage SnapServerXSR 40 Manuale utente
Overland Storage
Overland Storage SnapServer Manuale di servizio
Overland Storage
Overland Storage REO 4600 Manuale utente
Overland Storage
Overland Storage NEO 8000E Manuale utente
Overland Storage
Overland Storage SnapSAN S1000 Manuale utente
Overland Storage
Overland Storage ARCvault Series Manuale utente
Overland Storage
Overland Storage ARCvault Series Guida
