Owon SDS-E Series Manuale utente

General Warranty

OWON warrants that the product will be free from defects in materials and workmanship

for a period of 3 years from the date of purchase of the product by the original purchaser

from the OWON Company. And the warranty period of accessories such as probe is 12

month. This warranty only applies to the original purchaser and is not transferable to the

third party. If the product proves defective during the warranty period, OWON either will

repair the defective product without charge for parts and labor, or will provide a

replacement in exchange for the defective product. Parts, modules and replacement

products used by OWON for warranty work may be new or reconditioned like new

performance. All replaced parts, modules and products become the property of OWON.

In order to obtain service under this warranty, Customer must notify OWON of the defect

before the expiration of the warranty period. Customer shall be responsible for packaging

and shipping the defective product to the service center designated by OWON, and with a

copy of customer proof of purchase.

This warranty shall not apply to any defect, failure or damage caused by improper use or

improper or inadequate maintenance and care. OWON shall not be obligated to furnish

service under this warranty a) to repair damage resulting from attempts by personnel other

than OWON representatives to install, repair or service the product; b) to repair damage

resulting from improper use or connection to incompatible equipment; c) to repair any

damage or malfunction caused by the use of non-OWON supplies; or d) to service a

product that has been modified or integrated with other products when the effect of such

modification or integration increases the time or difficulty of servicing the product.

Please contact the nearest OWON's Sales and Service Offices for services or a complete

copy of the warranty statement.

For better after-sales service, please visit www.owon.com.cn and register the purchased

product online.

Excepting the after-sales services provided in this summary or the applicable warranty

statements, OWON will not offer any guarantee for maintenance definitely declared or hinted,

including but not limited to the implied guarantee for marketability and special-purpose

acceptability. OWON should not take any responsibilities for any indirect, special or consequent

damages.

Table of Contents

1. General Safety Requirements.......................................................................................... 1

2. Safety Terms and Symbols............................................................................................... 2

3. Quick Start.......................................................................................................................4

Introduction to the Structure of the Oscilloscope.....................................................................4

Front Panel ...............................................................................................................................................4

Right Side Panel.......................................................................................................................................5

Rear Panel ................................................................................................................................................6

Control (key and knob) Area....................................................................................................................7

User Interface Introduction........................................................................................................ 8

How to Implement the General Inspection.............................................................................10

How to Implement the Function Inspection............................................................................10

How to Implement the Probe Compensation..........................................................................11

How to Set the Probe Attenuation Coefficient........................................................................ 12

How to Use the Probe Safely.....................................................................................................13

How to Implement Self-calibration..........................................................................................13

Introduction to the Vertical System......................................................................................... 14

Introduction to the Horizontal System.................................................................................... 15

Introduction to the Trigger System .........................................................................................15

How to Measure Automatically................................................................................................16

How to Use Autoscale................................................................................................................ 17

4. Communication with PC............................................................................................... 18

Using USB Port..........................................................................................................................18

Using LAN Port .........................................................................................................................19

Connect directly .....................................................................................................................................19

Connect through a router........................................................................................................................20

Using COM Port........................................................................................................................22

5. Appendix ........................................................................................................................ 23

Appendix A: Enclosure............................................................................................................. 23

Appendix B: General Care and Cleaning ...............................................................................23

Appendix C: USB Disk Requirements.....................................................................................23

1. General Safety Requirements

Before any operations, please read the following safety precautions to avoid any

possible bodily injury and prevent this product or any other products connected

from damage. In order to avoid any contingent danger, this product is only used

within the range specified.

Only the qualified technicians can implement the maintenance.

To avoid Fire or Personal Injury:

Connect the probe correctly. The grounding end of the probe corresponds to the

grounding phase. Please don't connect the grounding end to the positive phase.

Use Proper Power Cord. Use only the power cord supplied with the product and

certified to use in your country.

Connect or Disconnect Correctly. When the probe or test lead is connected to a

voltage source, please do not connect and disconnect the probe or test lead at random.

Product Grounded. This instrument is grounded through the power cord grounding

conductor. To avoid electric shock, the grounding conductor must be grounded. The

product must be grounded properly before any connection with its input or output

terminal.

When powered by AC power, it is not allowed to measure AC power source

directly, because the testing ground and power cord ground conductor are

connected together, otherwise, it will cause short circuit.

To avoid electric shock, there must be a ground wire connect between ground

and the ground port (on the back of product panel).

Check all Terminal Ratings. To avoid fire or shock hazard, check all ratings and

markers of this product. Refer to the user's manual for more information about ratings

before connecting to the instrument.

Do not operate without covers. Do not operate the instrument with covers or panels

removed.

Use Proper Fuse. Use only the specified type and rating fuse for this instrument.

Avoid exposed circuit. Do not touch exposed junctions and components when the

instrument is powered.

Do not operate if in any doubt. If you suspect damage occurs to the instrument, have

it inspected by qualified service personnel before further operations.

Use your Oscilloscope in a well-ventilated area. Make sure the instrument installed

with proper ventilation, refer to the user manual for more details.

Do not operate in wet conditions.

Do not operate in an explosive atmosphere.

Keep product surfaces clean and dry.

2. Safety Terms and Symbols

Safety Terms

Terms in this manual. The following terms may appear in this manual:

Warning: Warning indicates the conditions or practices that could result in

injury or loss of life.

Caution: Caution indicates the conditions or practices that could result in

damage to this product or other property.

Terms on the product. The following terms may appear on this product:

Danger: It indicates an injury or hazard may immediately happen.

Warning: It indicates an injury or hazard may be accessible potentially.

Caution: It indicates a potential damage to the instrument or other property might occur.

Safety Symbols

Symbols on the product. The following symbol may appear on the product:

Hazardous Voltage

Refer to Manual

Protective Earth Terminal

Chassis Ground

Test Ground

2. Safety Terms and Symbols

To avoid body damage and prevent product and connected equipment damage, carefully

read the following safety information before using the test tool. This product can only be

used in the specified applications.

Warning:

The two channels of the oscilloscope are non-isolated electrically. The channels

should adopt common basis during measuring. To prevent short circuits, the 2 probe

ground must not be connected to 2 different non-isolated DC level.

Warning:

The channels should adopt common basis during measuring. To prevent short

circuits, the 2 probe ground must not be connected to 2 different non-isolated DC

level.

The diagram of the oscilloscope ground wire connection:

Ground Clip

Signal Input

Oscilloscope Electrical Outlet

Probe

Power Cord

It is not allowed to measure AC power when the AC-powered oscilloscope is

connected to the AC-powered PC through the ports.

Warning:

To avoid fire or electrical shock

, when the oscilloscope input signal

connected

is more than 4

2V peak (30Vrms) or on circuits of more than

4800VA

, please take note of below items:

Only use accessory insulated voltage probes and test lead.

Check the accessories such as probe before use and replace it if

there are any damages.

Remove probes, test leads and other accessories immediately after

use.

Remove USB cable which connects oscilloscope and computer.

Do

not apply input voltages above the rating of the instrument

because the probe tip voltage will directly transmit to the

oscilloscope. Use with caution when the probe is set as 1:1.

Do not use exposed metal BNC or banana plug connectors.

Do not insert metal objects into connectors.

3. Quick Start

Introduction to the Structure of the Oscilloscope

When you get a new-type oscilloscope, you should get acquainted with its front panel at

first and the digital storage oscilloscope is no exception. This chapter makes a simple

description of the operation and function of the front panel of the oscilloscope, enabling

you to be familiar with the use of the oscilloscope in the shortest time.

Front Panel

The oscilloscope offers a simple front panel with distinct functions to users for their

completing some basic operations, in which the knobs and function pushbuttons are

included. The knobs have the functions similar to other oscilloscopes. The 5 buttons

(F1 - F5) in the column on the right side of the display screen or in the row under the

display screen (H1 - H5) are menu selection buttons, through which, you can set the

different options for the current menu. The other pushbuttons are function buttons,

through which, you can enter different function menus or obtain a specific function

application directly.

12 3

Figure 3-1 Front panel

1. Power on/off

2. Display area

3. Control (key and knob) area

4. Probe Compensation: Measurement signal(5V/1KHz) output

5. EXT Trigger Input

6. Signal Input Channel

7. Menu off

3. Quick Start

Right Side Panel

Figure 3-2 Right side panel

1. USB Host port: It is used to transfer data when external USB equipment connects to

the oscilloscope regarded as "host device". For example: use this port to save waveform

file into USB flash disk.

2. USB Device port: It is used to transfer data when external USB equipment connects to

the oscilloscope regarded as "slave device". For example: to use this port when connect

PC to the oscilloscope by USB.

3. COM / VGA port (Optional): To connect the oscilloscope with external equipment as

serial port, or to connect the oscilloscope with a monitor or a projector as VGAoutput.

4. Trigger Out & Pass/Fail Out (MCX connector).

5. LAN port: the network port which can be used to connect with PC.

3. Quick Start

Rear Panel

Figure 3-3 Rear Panel

1. Handle

2. Air vents

3. AC power input jack

4. Fuse

5. Foot stool (which can adjust the tilt angle of the oscilloscope)

3. Quick Start

Control (key and knob) Area

6 7 8

Figure 3-4 Keys Overview

1. Menu option setting: H1 - H5

2. Menu option setting: F1 - F5

3. Menu off：turn off the menu

4. M knob (Multipurpose knob): when a ○

M symbol appears in the menu, it indicates

you can turn the M knob to select the menu or set the value. You can press it to close

the menu on the left.

5. Function key area: Total 12 keys

6. Vertical control area with 3 keys and 4 knobs.

"CH1 MENU" and "CH2 MENU" correspond to setting menu in CH1 and CH2,

"Math" key refer to math menu, the math menu consists of six kinds of operations,

including CH1-CH2, CH2-CH1, CH1+CH2, CH1*CH2, CH1/CH2 and FFT. Two

"VERTICAL POSITION" knob control the vertical position of CH1/CH2, and two

"VOLTS/DIV" knob control voltage scale of CH1, CH2.

7. Horizontal control area with 1 key and 2 knobs.

"HORIZONTAL POSITION" knob control trigger position, "SEC/DIV" control time

base, "HORIZ MENU" key refer to horizontal system setting menu.

8. Trigger control area with 3 keys and 1 knob.

"TRIG LEVEL" knob is to adjust trigger voltage. Other 3 keys refer to trigger system

setting.

3. Quick Start

User Interface Introduction

1 2 3

46 7 8

15161718

Figure 3-5 Illustrative Drawing of Display Interfaces (SDS5032E(V) shown)

1. Waveform DisplayArea.

2. The state of trigger, including:

Auto: Automatic mode and acquire waveform without triggering.

Trig: Trigger detected and acquire waveform.

Ready: Pre-triggered data captured and ready for a trigger.

Scan: Capture and display the waveform continuously.

Stop: Data acquisition stopped.

3. The purple T pointer indicates the horizontal position for the trigger.

4. The pointer indicates the trigger position in the internal memory.

5. The two yellow dotted lines indicate the size of the viewing expanded window.

6. It shows present triggering value and displays the site of present window in

internal memory.

7. It shows setting time.

8. It indicates that there is a USB disk connecting with the oscilloscope.

9. The waveform of CH1.

10. The purple pointer shows the trigger level position for CH1.

11. The positions of two purple dotted line cursors measurements.

12. The waveform of CH2.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Owon Apparecchiature di prova

Owon

Owon HDS200 Series Manuale utente

Owon

Owon AG4101 Manuale utente

Owon

Owon DGE3000 Series Manuale utente

Owon

Owon SDS1000 Manuale utente

Owon

Owon HDS300 Series Manuale utente

Owon

Owon XDS3000 Series Manuale utente

Owon

Owon XDS3104A Manuale utente

Owon

Owon 4-CH VDS6000 Series Manuale utente

Owon

Owon MSO7102TD Manuale utente

Owon

Owon SDS5032E(V) Manuale utente

Owon

Owon PDS8102T Manuale utente

Owon

Owon VDS Series Manuale utente

Owon

Owon HDS2202 Manuale utente

Owon

Owon VDS1022l Manuale utente

Owon

Owon MSO series Manuale utente

Owon

Owon HDS272S Manuale utente

Owon

Owon SDS1104 Manuale utente

Owon

Owon VDS Series Manuale utente

Owon

Owon MSO7102T Manuale utente

Owon

Owon VDS6000 Series Manuale utente

Owon

Owon PDS series Manuale utente

Owon

Owon tds series Manuale utente

Owon

Owon XDS4000 Series Manuale utente

Owon

Owon TAO3000 Dual-Channel Series Manuale utente

Manuali Apparecchiature di prova popolari di altre marche

SMART

SMART KANAAD SBT XTREME 3G Series Manuale utente

Agilent Technologies

Agilent Technologies BERT Serial Manuale utente

Agilent Technologies

Agilent Technologies N3280A Manuale utente

Vernier

Vernier Go Direct Voltage Manuale utente

Lifeloc

Lifeloc R.A.D.A.R. Manuale utente

Fluke

Fluke T5-600 Istruzioni per l'uso e l'installazione

Mercury

Mercury TSL01 Manuale utente

MAHA

MAHA MBT Series Manuale utente

Fuji Electric

Fuji Electric P-61 Manuale utente

ETC

ETC SealerAtor Manuale utente

Skyfine

Skyfine ETHYWAY V2 Manuale utente

Appion

Appion G5 Twin Manuale utente

PCB Piezotronics

PCB Piezotronics 8159-0112A Manuale utente

BW Technologies

BW Technologies MicroDock II Manuale utente

Sun Nuclear

Sun Nuclear 1027 Manuale utente

Biomark

Biomark HPR LITE READER Manuale utente

Hioki

Hioki 3169-20 Manuale utente

Ashcroft

Ashcroft ATE-100 Manuale utente