Panduit CTFP-25 Manuale utente

CTFP-25

PA29442A01

Rev. 02 3-2019

BENCHMOUNT PNEUMATIC CRIMPING PRESS

OPERATING INSTRUCTIONS

Original Instructions

TO REDUCE THE RISK OF INJURY, USER

MUST READ INSTRUCTION MANUAL

NOTE: In the interest of higher quality and value, Panduit products are

continually being improved and updated. Consequently, pictures may vary

from the enclosed product.

For the most current version of this instruction manual, go to

www.panduit.com.

Email:

techsupport@panduit.com

EU Website:

www.panduit.com/emea

EU Email:

emeatoolservicecenter

@panduit.com

www.panduit.com

Panduit Corp.

USA Technical Support

Tel: 800-777-3300

Panduit Europe • EMEA Service Center

Tel: +31 546 580 452 • Fax: +31 546 580 441

ENGLISH

PA29442A01_02_ENG Page: 1 of 8 3-2019

Table of Contents

1. SAFETY ....................................................................................................................2

1.1 Basic information.......................................................................................................2

1.2 Symbols.....................................................................................................................2

1.3 Dangerousness of the machine .................................................................................2

1.4 Designated use..........................................................................................................2

1.5 Sources of danger .....................................................................................................3

1.6 Work places...............................................................................................................3

1.7 Safety devices ...........................................................................................................3

1.8 Permitted operators...................................................................................................3

1.9 Guarantee..................................................................................................................3

2. DESCRIPTION..........................................................................................................4

2.1 Application.................................................................................................................4

2.2 Components..............................................................................................................4

2.3 Accessories...............................................................................................................4

3. OPERATION .............................................................................................................5

3.1 Commissioning..........................................................................................................5

3.2 Operation...................................................................................................................5

4. MAINTENANCE.........................................................................................................6

4.1 Cleaning ....................................................................................................................6

4.2 Lubrication................................................................................................................6

5. SPARE PARTS .........................................................................................................7

6. TECHNICAL DATA....................................................................................................8

Keep this for future use!

ENGLISH

PA29442A01_02_ENG Page: 2 of 8 3-2019

1. SAFETY

1.1 Basic information

The basic prerequisitefor ensuring safe useand continuous operation of the CTFP-25 is knowledgeof

and compliance with the safetyinstructions.

It is a question of your own safety!

All persons working with the CTFP-25 must observe the notes on safety.

In addition, rules and regulations that apply to the place of use, particularly regarding accident

prevention, must be observed.

1.2 Symbols

The following symbols will be used in these operating instructions:

indicates a possible accident or injury hazard and/or possible damage to the CTFP-25.

!indicates notes on application.

1.3 Dangerousness of the machine

The CTFP-25 has been constructed according to recognized technical safety regulations and has

undergone a safety examination and received official acceptance.

It is equipped with safety devices.

However, operating error and misuse could present a danger to:

•life and limb of the operator,

•the machine.

The CTFP-25 should only be used:

•for the designated application and

•in perfect condition with regard to technicalsafety.

All persons involved with commissioning, operating and maintaining the CTFP-25, must:

•be appropriately qualified and follow these operating instructionsprecisely.

1.4 Designated use

The CTFP-25 is to be used exclusively for crimping wire-end ferrules with cross sections between

#24 –14 AWG (0,25 and 2,5 mm²). Under no circumstances should large metal parts or similar objects

be introduced; the die set will be ruined.

Unauthorized amendments to the CTFP-25 are prohibited for safety reasons!

Observation of all instructions and compliance with the prescribed operating conditions

are part of the designated use.

ENGLISH

PA29442A01_02_ENG Page: 3 of 8 3-2019

1.5 Sources of danger

The CTFP-25 must only be operated when the finger guard is screwed on. Only filtered compressed

air with a maximum pressure of 6 bar can be used.

Disconnect the machine from the compressed air before working on the CTFP-25, during breaks and

when the device is not in use. Do not pull on the compressed air tubing to disconnect.

1.6 Work places

The following should be avoided for operation and storage:

•damp or dusty places,

•places which are subject to high levels of heat, direct sunlight or low temperatures:

operating range: 59°F to 95°F (15 °C to 35 °C).

Protect the compressed air tubing from heat, oil and sharp edges.

1.7 Safety devices

The CTFP-25 has a finger guard at the front as a contact safety device.

Under no circumstances should this be removed.

The CTFP-25 is stopped when disconnected from the compressed air supply.

1.8 Permitted operators

Only authorized and instructed operators can work on the CTFP-25. The operator is responsible to

third parties in the working area.

The owner must:

•make the operating instructions available to the operatorand

•make sure that the operator has read and understood the instructions

1.9 Guarantee

In principle, our "General terms of purchase and delivery" apply. These are available to the owner

when the contract is concluded at the latest.

Guarantee and liability claims resulting from damage to personnel or property are inadmissible if the

following points have been violated:

•Non-designated use of the CTFP-25.

•Inappropriate working places.

•Inappropriate use and use which goes beyond that described in the operatinginstructions.

•Unauthorized structural amendments to the CTFP-25.

•Continued use of the CTFP-25 when a malfunction has beenestablished.

•Repairs carried outinappropriately.

!Only use original spare parts

ENGLISH

PA29442A01_02_ENG Page: 4 of 8 3-2019

2. DESCRIPTION

2.1 Application

The CTFP-25 is a pneumatic crimping tool for wire-end ferrules with a cross-section of between

#24 –14 AWG (0,25 and 2,5 mm²).

The CTFP-25 comprises a tabletop unit and a foot-operated switch. As both hands are free to insert

the wire fitted with wire-end ferrules, the CTFP-25 is ideally suited to pre-confectioning cables.

2.2 Components

Figure 1 - Spare Parts

1 Tabletop unit

2 Compressed air tubing

3 Foot-operated switch

4 Switch

Storage compartment for wire-end

ferrules

6 Head

7 Finger guard

8 Die set

2.3 Accessories

9 Table clamp

ENGLISH

PA29442A01_02_ENG Page: 5 of 8 3-2019

3. OPERATION

3.1 Commissioning

•Check whether finger guard (1) is present

andis sitting firm.

•Check whether the die set (2) is free from

foreign matter.

•Check whether the pneumatic tubing nuts

(3) have been tightenedfirmly.

•Insert the table clamp (4) into thebore hole

in the tabletop unit and screw tightly to the

worktable.

•Check the compressed-air supply:

min. 4 bar, max. 6 bar filtered air

•Connect the free connection (5) on

thefoot switch to the compressed-air

supply

Figure 2 - Commissioning

3.2 Operation

•Introduce stripped wire with wire-end

ferrules alreadyfitted, at the side(1) or

fromthefront (2).

•Press the switch (3), the crimping

processwill be triggered.

•Release the switch (4), the crimped wire

canbe removed again (5).

Figure 3 - Operation

ENGLISH

PA29442A01_02_ENG Page: 6 of 8 3-2019

4. MAINTENANCE

The CTFP-25 must be

opened. Disconnect

compressed air!

4.1 Cleaning

•Unscrew hexagon socket screw(1).

•Pull out the die set (2).

•Clean die set (3) and lightly oil pivot(4).

•Push in die set (5).

•Tighten hexagon socket screw(6).

Figure 4 - Cleaning

4.2 Lubrication

•Unscrew the head (1).

•Remove the spring (2) and piston(3).

•Lubricate the two arms of the die set(4) (e. g.

CHEMPLEX 746).

•Insert arms of the die set and spring.

•Insert head (5) and fasten fingertight.

Figure 5 - Lubrication

ENGLISH

PA29442A01_02_ENG Page: 7 of 8 3-2019

5. SPARE PARTS

Address:

Panduit Corp.

16530 W. 163rd St.

Lockport, IL 60441 U.S.A.

Tel. 1-800-777-3300

The following spare parts can be ordered with the

appropriate Article No.

Figure 6 - Spare parts

No.

Part

Article No.

No.

Part

Article No.

Compressed air tube

008137

Head part incl. screw and

005473

Body

001564

Axis

001569

Adhesive rubber pads

001727

Die Set

005540

Sealing ring

001135

Finger spring

001556

Piston

005121

Finger guard

005521

Spring

001555

Foot-operated switch

005541

7 Head complete 008791 14 Table clamp 001551

ENGLISH

PA29442A01_02_ENG Page: 8 of 8 3-2019

6. TECHNICAL DATA

Instrument...........................................................................................................Pneumatic Crimper

Crimping range...............................................................................#24 - #14 AWG 0,25 – 2,5 mm²

Compressed-air connection.............................................................................................. min. 4 bar

........................................................................................................................................ max. 6 bar

Air consumption.......................................................................................0.2 liter / Crimping at 5 bar

Dimensions (diameter x length x height)................................................................. 7.8” x 5.3” x 2.9”

.........................................................................................................................(200 x 135 x 75 mm)

Weight .........................................................................................................approx. 6.2 lbs. (2.8 kg)

Acoustic pressure emissions LpA.....................................................................................< 70 dB (A)

Name plate

Panduit Corp.

18900 Panduit Drive

Tinley Park, IL 60487 USA

CTFP-25

Cross Section (working range)

Serial Number

Manufactured: MM-YY

Compliance

Country of Origin

Q. C. Number

CTFP-25 Label

Indice

Lingue:

Altri manuali Panduit Utensili per crimpatura

Panduit

Panduit CTFP-100 Manuale utente

Panduit

Panduit Ezair CA9 Manuale utente

Panduit

Panduit BlackFin CT-2980/STBT Manuale utente

Panduit

Panduit MSPT-1.3 Manuale utente

Panduit

Panduit PAT4.0 Series Manuale utente

Panduit

Panduit CT-1000 Guida per l'amministratore

Panduit

Panduit CT-3001 Manuale utente

Panduit

Panduit CT-1123 Manuale di istruzioni

Panduit

Panduit CT-1123 Manuale di istruzioni

Panduit

Panduit CT-1002 Manuale

Panduit

Panduit CT-2500 Manuale utente

Panduit

Panduit Blackfin CT-2980/TO Manuale utente

Panduit

Panduit Black Fin CT-2931/STCVUK Manuale utente

Panduit

Panduit Contour Crimp CT-1015 Manuale utente

Panduit

Panduit BlackFin CT-2931/STBT Manuale utente

Panduit

Panduit BlackFin CT-3980/BT Manuale utente

Panduit

Panduit CT-920 Series Manuale utente

Panduit

Panduit BlackFin CT-2600/L Manuale utente

Panduit

Panduit PBTMT Manuale utente

Panduit

Panduit BlackFin CT-2300/ST Manuale utente

Panduit

Panduit BlackFin CT-2300 Series Manuale utente

Panduit

Panduit Contour Crimp CT-1551 Manuale utente

Panduit

Panduit Black Fin CT-2931 Series Manuale utente

Panduit

Panduit CT-600-A Manuale utente

Manuali Utensili per crimpatura popolari di altre marche

JST

JST CS 10 Manuale utente

molex

molex 63811-5100 Manuale utente

Danfoss

Danfoss ET4200 Manuale utente

Tyco Electronics

Tyco Electronics PRO-CRIMPER III Manuale utente

TE Connectivity

TE Connectivity 2063528-1 Manuale utente

molex

molex 63825-3000 Manuale utente

Tyco Electronics

Tyco Electronics 69156-1 Manuale utente

CRH

CRH CRL CBLHCT1 Manuale utente

Emerson

Emerson Klauke ES 105CFM Manuale utente

KIMBALL MIDWEST

KIMBALL MIDWEST 27-798 Manuale di istruzioni

Danfoss

Danfoss ET4350 Manuale utente

Milwaukee

Milwaukee M18 Manuale utente

HOGERT

HOGERT HT1P169 Manuale utente

Textron

Textron ESG105L Manuale utente

Tyco Electronics

Tyco Electronics 90035-3 Manuale utente

Emerson

Emerson Klauke ES 20RMCCFB Manuale utente

Continental Refrigerator

Continental Refrigerator PC150HD Manuale utente

TE Connectivity

TE Connectivity ERGOCRIMP 1-1579001-3 Manuale utente