Paradyne Micro Interface Module MIM-2000F Manuale utente

MIM2-A2-GZ42-00 June 2005 1

MIM-2000F

Installation Instructions

Document Number MIM2-A2-GZ42-00

June 2005

Contents

Software and Firmware License Agreement ...................................................... 1

Product Documentation Online .......................................................................... 3

Unpacking and Inspecting the Equipment ......................................................... 3

Installing the MIM-2000F ................................................................................... 3

Installing and Cabling SFP Transceivers ........................................................... 4

Managing the MIM-2000F .................................................................................. 4

LED Indicators ................................................................................................... 5

Regulatory Notices ............................................................................................ 5

Warranty, Sales, Service, and Training Information ........................................... 6

Software and Firmware License Agreement

The terms and conditions of this License Agreement (the “Agreement”) will apply

to the software and/or firmware (individually or collectively the “Software”)

incorporated into the Paradyne product (the “Product”) purchased by you and any

derivatives obtained from the Software, including any copy of either. If you have

executed a separate written agreement covering the Software supplied to you

under this purchase, such separate written agreement shall govern.

Paradyne Corporation (“Paradyne”) grants to you, and you (“Licensee”) agree to

accept a personal, non-transferable, non-exclusive, right (without the right to

sublicense) to use the Software, solely as it is intended and solely as incorporated

ONCE YOU HAVE READ THIS LICENSE AGREEMENT AND AGREE TO ITS

TERMS, YOU MAY USE THE SOFTWARE AND/OR FIRMWARE INCORPORATED

INTO THE PARADYNE PRODUCT. BY USING THE PARADYNE PRODUCT YOU

SHOW YOUR ACCEPTANCE OF THE TERMS OF THIS LICENSE AGREEMENT.

IN THE EVENT THAT YOU DO NOT AGREE WITH ANY OF THE TERMS OF THIS

LICENSE AGREEMENT, PROMPTLY RETURN THE UNUSED PRODUCT IN ITS

ORIGINAL PACKAGING AND YOUR SALES RECEIPT OR INVOICE TO THE

LOCATION WHERE YOU OBTAINED THE PARADYNE PRODUCT OR THE

LOCATION FROM WHICH IT WAS SHIPPED TO YOU, AS APPLICABLE, AND YOU

WILL RECEIVE A REFUND OR CREDIT FOR THE PARADYNE PRODUCT

PURCHASED BY YOU.

2June 2005 MIM2-A2-GZ42-00

in the Product purchased from Paradyne or its authorized distributor or reseller

under the following terms and conditions:

1. Ownership: The Software is the sole property of Paradyne and/or its licensors.

The Licensee acquires no title, right or interest in the Software other than the

license granted under this Agreement.

2. Licensee shall not use the Software in any country other than the country in

which the Product was rightfully purchased except upon prior written notice to

Paradyne and an agreement in writing to additional terms.

3. The Licensee shall not reverse engineer, decompile or disassemble the

Software in whole or in part.

4. The Licensee shall not copy the Software except for a single archival copy.

5. Except for the Product warranty contained in the manual, the Software is

provided “AS IS” and in its present state and condition and Paradyne makes

no other warranty whatsoever with respect to the Product purchased by you.

THIS AGREEMENT EXPRESSLY EXCLUDES ALL OTHER WARRANTIES,

WHETHER EXPRESS OR IMPLIED, OR ORAL OR WRITTEN, INCLUDING

WITHOUT LIMITATION:

a. Any warranty that the Software is error-free, will operate uninterrupted in

your operating environment, or is compatible with any equipment or

software configurations; and

b. ANY AND ALL IMPLIED WARRANTIES, INCLUDING WITHOUT

LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS

FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT.

Some states or other jurisdictions do not allow the exclusion of implied

warranties on limitations on how long an implied warranty lasts, so the above

limitations may not apply to you. This warranty gives you specific legal rights,

and you may also have other rights which vary from one state or jurisdiction to

another.

6. In no event will Paradyne be liable to Licensee for any consequential,

incidental, punitive or special damages, including any lost profits or lost

savings, loss of business information or business interruption or other

pecuniary loss arising out of the use or inability to use the Software, whether

based on contract, tort, warranty or other legal or equitable grounds, even if

Paradyne has been advised of the possibility of such damages, or for any

claim by any third party.

7. The rights granted under this Agreement may not be assigned, sublicensed or

otherwise transferred by the Licensee to any third party without the prior

written consent of Paradyne.

8. This Agreement and the license granted under this Agreement shall be

terminated in the event of breach by the Licensee of any provisions of this

Agreement.

9. Upon such termination, the Licensee shall refrain from any further use of the

Software and destroy the original and all copies of the Software in the

possession of Licensee together with all documentation and related materials.

10. This Agreement shall be governed by the laws of the State of Florida, without

regard to its provisions concerning conflicts of laws.

MIM2-A2-GZ42-00 June 2005 3

Product Documentation Online

Complete documentation for Paradyne products is available at

www.paradyne.com. Select Support →Technical Manuals.

To order a paper copy of a Paradyne document, or to speak with a sales representative,

please call 1-727-530-2000.

Unpacking and Inspecting the Equipment

HANDLING PRECAUTIONS FOR

STATIC-SENSITIVE DEVICES

This product is designed to protect sensitive components from damage

due to electrostatic discharge (ESD) during normal operation. When

performing installation procedures, however, take proper static control

precautions to prevent damage to equipment. If you are not sure of the

proper static control precautions, contact your nearest sales or service

representative.

If there is any visible damage, do not attempt to install the MIM-2000F; contact

your sales representative.

Installing the MIM-2000F

The MIM-2000F Micro Interface Module provides additional uplink ports for the

BSX8000-5 Broadband Services Switch or 4929 DSLAM.

All MIMs are hot-swappable, although removal of a MIM disengages the upstream

network connection for the DSLAM.

To install the MIM-2000F:

Procedure

1. Using a flat-blade screwdriver to loosen the fastening screws, remove the

cover plate from the MIM port on the front of your BSX8000 or 4929 DSLAM.

CAUTION: The cover plate should be stored for possible future use. If the MIM

is removed from your BSX8000 or DSLAM, it must be replaced with either

another MIM or a cover plate. Do not operate a BSX8000 or DSLAM with an

open MIM port.

2. Align the MIM-2000F with the module guides inside the MIM port.

Lnk 1 Act Lnk 2 Act

MIM-2000F

05-17669

4June 2005 MIM2-A2-GZ42-00

3. Slide the MIM-2000F firmly into place. Do not use excessive force.

4. Secure the MIM-2000F by tightening the fastening screws on the MIM

faceplate with a flat-blade screwdriver.

Installing and Cabling SFP Transceivers

Both SFP copper and fiber optic transceivers may be installed in the MIM-2000F.

The following SFP fiber optic transceivers are available:

SFP-MMF – GigE SFP Multimode Fiber Optic Transceiver, Short Reach

SFP-SMF10 – GigE SFP Single Mode Fiber Optic Transceiver, 10Km Reach

SFP-SMF40 – GigE SFP Single Mode Fiber Optic Transceiver, 40Km Reach

SFP-SMF80 – GigE SFP Single Mode Fiber Optic Transceiver, 80Km Reach

To install SFP transceivers in the MIM-2000F:

Procedure

1. Insert an SFP transceiver into an SFP socket on the MIM-2000F.

2. Insert the LC connector of your fiber optic cable into the SFP transceiver.

3. Observing the minimum bend radius for your cable, fasten it in such a way that

it will not be kinked or snagged in the course of other cabling. If you do not

know the specifications for your cable, maintain a radius of at least ten times

the cable diameter.

4. Repeat for all the sockets you intend to use.

Managing the MIM-2000F

The configuration and monitoring of the integrated switch on the MIM-2000F is

performed through the management screens of the BSX8000 or 4929 DSLAM that

hosts this module. See the BSX8000-5 Installation Instructions or 4929 DSLAM

Installation Guide and the NMS User’s Guide.

05-17670

Lnk 1 Act Lnk 2Act

MIM-2000F

MIM2-A2-GZ42-00 June 2005 5

LED Indicators

Each port is associated with two LEDs: Lnk (Link) and Act (Active):

Regulatory Notices

UNITED STATES – EMI NOTICE:

This equipment has been tested and found to comply with the limits for a

Class A digital device, pursuant to Part 15 of the FCC rules. These limits

are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial

environment. This equipment generates, uses, and can radiate radio

frequency energy and, if not installed and used in accordance with the

instruction manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is

likely to cause harmful interference in which case the user will be

required to correct the interference at his own expense.

The authority to operate this equipment is conditioned by the

requirements that no modifications will be made to the equipment

unless the changes or modifications are expressly approved by

Paradyne Corporation.

CANADA – EMI NOTICE:

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003

du Canada.

Table 1. Front Panel LEDs

LED State Indication

Lnk (Link) Solid green Connection is established

No illumination Connection is not established

Act (Active) No illumination No data activity on the circuit

Flashing amber Data is flowing through the circuit

6June 2005 MIM2-A2-GZ42-00

EUROPEAN REGULATORY COMPLIANCE

The following regulatory compliance information applies to the

MIM-2000F as installed in the 4929 DSLAM or BSX8000-5 Broadband

Services Switch:

This Class A product complies with European Norm EN55022.

Warning: In a domestic environment this product may cause radio

interference in which case the user may be required to take adequate

measures to correct the situation.

Warranty, Sales, Service, and Training Information

Contact your local sales representative, service representative, or distributor

directly for any help needed. For additional information concerning warranty, sales,

service, repair, installation, documentation, training, distributor locations, or

Paradyne worldwide office locations, use one of the following methods:

Internet: Visit the Paradyne World Wide Web site at www.paradyne.com.

(Be sure to register your warranty at www.paradyne.com/warranty.)

Telephone: Call our automated system to receive current information by fax or

to speak with a company representative.

— Within the U.S.A., call 1-800-870-2221

— Outside the U.S.A., call 1-727-530-2340

*MIM2-A2-GZ42-00*

Indice

Altri manuali Paradyne Hardware di rete

Paradyne

Paradyne COMSPHERE 3610 Aggiornamento firmware

Paradyne

Paradyne 7610 SNMP DSU Manuale utente

Paradyne

Paradyne 3151 Manuale tecnico

Paradyne

Paradyne 12000E Manuale utente

Paradyne

Paradyne COMSPHERE 3610 Manuale utente

Paradyne

Paradyne 3160-A3 Manuale

Paradyne

Paradyne Hotwire 8784 Manuale utente

Paradyne

Paradyne 3160-A4 Manuale

Paradyne

Paradyne COMSPHERE 3550 Series Manuale utente

Paradyne

Paradyne BitStorm 2600 IP DSLAM Manuale utente

Paradyne

Paradyne FrameSaver NP 64+ Manuale utente

Paradyne

Paradyne FrameSaver SLV 9626 Manuale utente

Paradyne

Paradyne 3172 Manuale utente

Paradyne

Paradyne FrameSaver SLV 9124 Manuale per l'uso e la cura

Paradyne

Paradyne COMSPHERE 6700 Series Manuale utente

Paradyne

Paradyne COMSPHERE 3610 Manuale utente

Paradyne

Paradyne HotWire 7924 Manuale utente

Paradyne

Paradyne COMSPHERE 6700 Series Manuale utente

Paradyne

Paradyne COMSPHERE 3550 Series Manuale utente

Paradyne

Paradyne 24-Port SHDSL Mini DSLAM SMD2000-24T Manuale utente

Paradyne

Paradyne iMarc SLV 9820-2M Manuale utente

Paradyne

Paradyne FrameSaver 9120 Manuale del proprietario

Paradyne

Paradyne 5030 Manuale utente

Paradyne

Paradyne Hotwire 7995 Manuale utente

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente