Parker Hi-Pro Manifold Manuale utente

Effective: July 2018

Hi-Pro Manifold

Effective: December 2022

Installation and Operation Manual

Hi-Pro Manifold

Page 1of 6

ECO-0251996

ISSUE: 01

Installation and Operation Manual

Hi-Pro Manifold

Parker Hannifin

Instrumentation Products Division Europe

Riverside Road, Barnstaple, Devon, EX31 1NP

United Kingdom

Telephone: 0044 1271 313131

IDENTIFICATION OF HAZARDS

NEVER adjust valves under pressure.

NEVER slacken or remove any valve parts under pressure.

NEVER use any mechanical aids i.e. wrenches, extensions to operate handles.

NEVER carry ball valves by the handle.

NEVER obscure valve body marking.

NEVER remove end connectors.

INSTALLATION

Wear suitable PPE before installation and follow appropriate site safety procedures.

Before installation, ensure that all valves are in the closed position.

Parker Hi-Pro manifold uses either integral fitting (A-LOK/CPI) or NPT female connections. For

connection, please refer to the appropriate installation instruction.

NPT: Use standard practice for NPT taper threads. Use an appropriate thread tape or sealant to

prevent galling.

A-LOK/CPI: See separate instruction sheet supplied with A-LOK products.

HANDLING AND STORAGE

Storage

There is no specified shelf-life.

Boxed products should be stored in a covered area, preferably indoors, and away from excessive

moisture, heat, or airborne contaminants.

The use of desiccant or corrosion inhibitors is not required during normal storage periods.

Page 2of 6

ECO-0251996

ISSUE: 01

Installation and Operation Manual

Hi-Pro Manifold

OPERATION

Ball Valve:

To close:Operate the handle until it is at 90° from the valve body centreline.

To open:Operate the handle until it is in line with the centreline of the body and reaches the stop

pin.

Movement is limited to 90° (except for vent ball valves) by a mechanical stop pin.

Ball valves should always be fully open or fully closed. Do not leave in a mid-position.

Three-way vent ball valves (red handle) have no firm centre-off position and are positioned visually.

Needle Valve

To close: Rotate handle clockwise until a stop is felt.

To open: Fully rotate the handle anti-clockwise until a stop is felt.

There are approximately three rotations between fully open and fully closed.

Do not force rotation past the stop, as damage may occur. Maximum torque is 6Nm

For anti-tamper designs only use the correct key for Parker manifolds.

MAINTENANCE

Parker Hi-Pro Manifolds are not user-serviceable, except for gland adjustment of the vent needle valve.

Gland adjustment becomes necessary when the valve is visibly leaking through the spindle just below

the operating handle, or prior to operation when no torque or resistance is evident when operating the

valve handle. Adjustment to the gland can be carried out to prevent leakage. Replacement bonnets

are available.

H-series Needle Valve Gland Adjustment (see page 3)

CAUTION: Adjustment of the gland must be carried out at zero pressure

1. Fully close the valve by turning the handle in a clockwise direction to stop lightly on seat

(max. 2 Nm).

2. Open the valve one full turn by rotating the handle in a counter clockwise direction.

3. Loosen gland lock nut.

4. Tighten gland nut to 11 Nm

5. Re-tighten gland lock nut to 25 Nm

Page 3of 6

ECO-0251996

ISSUE: 01

Installation and Operation Manual

Hi-Pro Manifold

H-Series Bonnet

sHANDLE

GLAND NUT

GLAND LOCK

NUT

Page 4of 6

ECO-0251996

ISSUE: 01

Installation and Operation Manual

Hi-Pro Manifold

These valves are primarily used for double isolation of an instrument, be that a gauge or a transmitter.

The primary and secondary valves are in the open position during normal operating conditions

allowing the process pressure to enter the gauge or transmitter to perform its function to give a

pressure reading. The primary valve is situated nearest to the inlet.

Standard operating sequence to perform safe venting:

1. Close the primary valve to block the pressure.

2. Open the vent valve to release the line pressure.

Page 5of 6

ECO-0251996

ISSUE: 01

Installation and Operation Manual

Hi-Pro Manifold

3. Close the secondary valve.

The double block gives two isolations to prevent process media escaping.

4. Close the vent valve.

5. Perform the required downstream functions.

6. Once the downstream functions, such as instrument calibration or replacement, have been

performed, open the primary and secondary valves again to allow pressure measurement to continue.

Vent plug: The valve is shipped with a vent plug, loose or installed as per the client’s requirements.

While venting the valve, this plug must be removed. The plug can be re-fitted for safety reasons or to

prevent ingress of the environment. That is the operator’s decision and should be in their operating

procedures. It is suggested that PTFE tape or sealant is used to prevent galling of the threads.

Page 6of 6

ECO-0251996

ISSUE: 01

Installation and Operation Manual

Hi-Pro Manifold

WARNING - USER RESPONSIBILITY

FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS DESCRIBED HEREIN OR

RELATED ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.

This document and other information from Parker Hannifin Corporation, its subsidiaries and authorized distributors provide product or

system options for further investigation by users having technical expertise. The user, through its own analysis and testing, is solely

responsible for making the final selection of the system and components and assuring that all performance, endurance, maintenance,

safety and warning requirements of the application are met. The user must analyse all aspects of the application, follow applicable

industry standards, and follow the information concerning the product in the current product catalogue and in any other materials

provided from Parker or its subsidiaries or authorized distributors. To the extent that Parker or its subsidiaries or authorized distributors

provide component or system options based upon data or specifications provided by the user, the user is responsible for determining

that such data and specifications are suitable and sufficient for all applications and reasonably foreseeable uses of the components or

systems.

Parker Hannifin Manufacturing Ltd

Instrumentation Products Division Europe

Riverside Road

Pottington Business Park

Barnstaple EX31 1NP

United Kingdom

Tel: +44 (0)1271 313131

www.parker.com/ipd

Indice

Altri manuali Parker Unità di controllo

Parker

Parker PSSN8M8A Istruzioni di installazione e manutenzione

Parker

Parker SC Series Manuale di riferimento

Parker

Parker CK1-DN Manuale utente

Parker

Parker CK-6D Manuale utente

Parker

Parker BAM20 Manuale utente

Parker

Parker PEV Manuale di servizio

Parker

Parker TFP Series Manuale utente

Parker

Parker 89-00B Guida

Parker

Parker TPQ Series Manuale utente

Parker

Parker 7121Z028 Istruzioni per il montaggio

Parker

Parker 8902/LS Manuale utente

Parker

Parker D 1FC Series Manuale utente

Parker

Parker C2 Series Istruzioni di installazione e manutenzione

Parker

Parker EP Series Pro-Bloc Manuale utente

Parker

Parker D*1VW*EE Series Manuale utente

Parker

Parker 20K Manuale utente

Parker

Parker RL Series Specifiche tecniche

Parker

Parker Series DFplus Manuale utente

Parker

Parker MI-101 Istruzioni operative e di manutenzione

Parker

Parker S4AD Manuale utente

Parker

Parker HASV08R Manuale utente

Parker

Parker PID00A-40X Series Manuale utente

Parker

Parker SciLog DINCon Istruzioni per il montaggio

Parker

Parker Vansco Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente