Patton electronics 2715RC Manuale utente

USER

MANUAL

MODEL 2715RC

NetLink-E1:

E1/Fractional E1 NTU

Rack Mount Card

SALES OFFICE

(301) 975-1000

TECHNICAL SUPPORT

(301) 975-1007

http://www.patton.com

Part# 07M2715RC

Doc# 08607U2-001

Rev. C

Revised 1/22/08

Dear Valued Customer,

Thank you for purchasing Patton Electronics products! We do

appreciate your business. I trust that you find this user manual helpful.

We manufacture one of the widest selections of data communica-

tions products in the world including CSU/DSU's, network termination units,

powered and self-powered short range modems, fiber optic modems, interface

converters, baluns, electronic data switches, data-line surge protectors, multi-

plexers, transceivers, hubs, print servers and much more. We produce these

products at our Gaithersburg, MD, USA, facility, and can custom manufacture

products for your unique needs.

We would like to hear from you. Please contact us in any of the fol-

lowing ways to tell us how you like this product and how we can meet your

product needs today and in the future.

Web: http://www.patton.com

Sales E-mail: [email protected]

Support E-mail: [email protected]

Phone - Sales (301) 975-1000

Phone - Support (301) 975-1007

Fax: (301) 869-9293

Mail: Patton Electronics Company

7622 Rickenbacker Drive

Gaithersburg, MD 20879 USA

We are committed to a quality product at a quality price. Patton

Electronics is ISO 9001 certified. We meet and exceed the highest standards

in the industry (CE, UL, etc.).

It is our business to serve you. If you are not satisfied with any

aspect of this product or the service provided from Patton Electronics or its

distributors, please let us know.

Thank you.

Burton A.Patton

Vice President

P.S. Please tell us where you purchased this product.

_________________________________________________________

An ISO-9001

Certified Company

PATTON MODEL 2715RC

TABLE OF CONTENTS

Section Page

1.0 General Information...............................................................2

1.1 Warranty Statement

1.2 Radio and TV Interference

1.3 CE and Telecommunication Approvals

1.4 Servie

2.0 General Information...............................................................4

2.1 Features

2.2 Description

3.0 Configuration .........................................................................5

3.1 Front card Configuration

3.2 Configuring the 1000RCM13348C Rear Card

4.0 Installation ..........................................................................11

4.1 The Model 1001R14 rack Chassis

4.1.1 The Rack Power Supply

4.2 Installing the Model 2715RC Into the Chassis

4.3 V.35 Terminal Connection

4.4 Connecting the Network and the V.35 Interfaces

4.4.1 Network Interface Connection

5.0 Operation.............................................................................14

5.1 Power-Up

5.2 LED Status Monitors

5.3 Loop (V.54) Diagnostics

5.3.1 Operating Local Loopback (LL)

5.3.2 Operating Remote Digital Loopback (RL)

5.4 Bit Error Rate (V.52) Diagnostics

Appendix A - Specifications ........................................................18

Appendix B - Factory Replacement Parts and Accessories.......19

Appendix C - Interface Pin Assignments ....................................20

1 2

PATTON MODEL 2715RC

TABLE OF CONTENTS

Section Page

1.0 General Information...............................................................2

1.1 Warranty Statement

1.2 Radio and TV Interference

1.3 CE and Telecommunication Approvals

1.4 Servie

2.0 General Information...............................................................4

2.1 Features

2.2 Description

3.0 Configuration .........................................................................5

3.1 Front card Configuration

3.2 Configuring the 1000RCM13348C Rear Card

4.0 Installation ..........................................................................11

4.1 The Model 1001R14 rack Chassis

4.1.1 The Rack Power Supply

4.2 Installing the Model 2715RC Into the Chassis

4.3 V.35 Terminal Connection

4.4 Connecting the Network and the V.35 Interfaces

4.4.1 Network Interface Connection

5.0 Operation.............................................................................14

5.1 Power-Up

5.2 LED Status Monitors

5.3 Loop (V.54) Diagnostics

5.3.1 Operating Local Loopback (LL)

5.3.2 Operating Remote Digital Loopback (RL)

5.4 Bit Error Rate (V.52) Diagnostics

Appendix A - Specifications ........................................................18

Appendix B - Factory Replacement Parts and Accessories.......19

Appendix C - Interface Pin Assignments ....................................20

1 2

1.3 CE AND TELECOMMUNICATION APPROVALS

The CE symbol on your Patton Electronics equipment indicates

that it is in compliance with the Electromagnetic Compatibility (EMC)

directive and the Low Voltage Directive (LVD) of the Union European

(EU). A Certificate of Compliance is available by contacting Technical

Support.

The Model 2715RC is in compliance with the Telecommunication

technical requirements CRT-12; 2.048 Mbps digital unstructured

leased line (D2048U) attachment requirements for terminal equipment

interface.

The Model 2715RC also meets the Telecommunication technical

requirements CTR-13; 2.048 Mbps digital structured leased lines

(D2048S) attachment requirements for terminal equipment interface.

1.4 SERVICE

All warranty and nonwarranty repairs must be returned freight pre-

paid and insured to Patton Electronics. All returns must have a Return

Materials Authorization number on the outside of the shipping contain-

er. This number may be obtained from Patton Electronics Technical

Support: (301) 975-1007; http://www.patton.com; or, support@pat-

ton.com.

NOTE: Packages received without an RMA number will not be

accepted.

Patton Electronics' technical staff is also available to answer any

questions that might arise concerning the installation or use of your

Model 2715RC. Technical Service hours: 8AM to 5PM EST, Monday

through Friday.

3 4

1.3 CE AND TELECOMMUNICATION APPROVALS

The CE symbol on your Patton Electronics equipment indicates

that it is in compliance with the Electromagnetic Compatibility (EMC)

directive and the Low Voltage Directive (LVD) of the Union European

(EU). A Certificate of Compliance is available by contacting Technical

Support.

The Model 2715RC is in compliance with the Telecommunication

technical requirements CRT-12; 2.048 Mbps digital unstructured

leased line (D2048U) attachment requirements for terminal equipment

interface.

The Model 2715RC also meets the Telecommunication technical

requirements CTR-13; 2.048 Mbps digital structured leased lines

(D2048S) attachment requirements for terminal equipment interface.

1.4 SERVICE

All warranty and nonwarranty repairs must be returned freight pre-

paid and insured to Patton Electronics. All returns must have a Return

Materials Authorization number on the outside of the shipping contain-

er. This number may be obtained from Patton Electronics Technical

Support: (301) 975-1007; http://www.patton.com; or, support@pat-

ton.com.

NOTE: Packages received without an RMA number will not be

accepted.

Patton Electronics' technical staff is also available to answer any

questions that might arise concerning the installation or use of your

Model 2715RC. Technical Service hours: 8AM to 5PM EST, Monday

through Friday.

3 4

DIP Switches S1 - S8

The configuration switches on S1 - S8 may be set to allow config-

uration for a wide range of applications. Default settings of S1 through

S8 are shown in the table below. Descriptions of each switch follow

the table.

Switch SW1: Line Coding

Use Switch SW1 to control the Network Line Coding options. Set

these options to be the same as the Line Coding given to you by your

Service Provider. If you are using two Model 2715RCs together as

short range modems, set both units identically, preferably to HDB3.

SW4 Line Framing & Coding

Off HDB3

On AMI

Line Coding Options:

High Density Bipolar 3 (HDB3): In HDB3 coding, the transmitter

deliberately inserts a bipolar violation when excessive zeros in

the data stream are detected. The receiver recognizes these

special violations and decodes them as zeros. This method

enables the network to meet minimum pulse density require-

ments. Use HDB3 unless AMI is required in your application .

Alternate Mark Inversion (AMI): AMI coding does not inherently

account for ones density. To meet this requirement, the user

should ensure that the data inherently meets pulse density

requirements.

3.0 CONFIGURATION

Two cards make up a single Model 2715RC G.703 Converter - a

front function card and a rear interface card. Each may require config-

uration depending upon the product application. This section describes

the location and orientation of the Model 2715RC’s configuration

switches and jumpers, and provides descriptions for all settings.

3.1 FRONT CARD CONFIGURATION

The Model 2715RC front card has a single bank of eight DIP

switches located on the top of the printed circuit board. Figure 1,

below, shows the position of the switches on the board.

Changing the DIP Switch Settings

Figure 2 shows the orientation of the DIP switches with respect to the

“ON” and “OFF” positions.

SWITCH SET SUMMARY TABLE

Position Function Factory Default Selected Option

SW1 Line Coding Off HDB3

SW2 CAS Multiframe Off Disabled

SW3 CRC-4 MF/Clock Mode Off Disabled

SW4 Clock Mode Off Network

SW5 DTE Rate Off

SW6 DTE Rate Off

SW7 DTE Rate Off

SW8 DTE Rate Off

2.048 Mbps

Clear

Channel

}

Figure 1. Model 2715RC board, showing DIP switch location

DIP Switch ON OFF

Figure 2. Close up of the configuration switches

NOTE: The ON position is oriented toward the front of the Model 2715RC.

ON OFF

Front Panel

DIP Switches S1 - S8

The configuration switches on S1 - S8 may be set to allow config-

uration for a wide range of applications. Default settings of S1 through

S8 are shown in the table below. Descriptions of each switch follow

the table.

Switch SW1: Line Coding

Use Switch SW1 to control the Network Line Coding options. Set

these options to be the same as the Line Coding given to you by your

Service Provider. If you are using two Model 2715RCs together as

short range modems, set both units identically, preferably to HDB3.

SW4 Line Framing & Coding

Off HDB3

On AMI

Line Coding Options:

High Density Bipolar 3 (HDB3): In HDB3 coding, the transmitter

deliberately inserts a bipolar violation when excessive zeros in

the data stream are detected. The receiver recognizes these

special violations and decodes them as zeros. This method

enables the network to meet minimum pulse density require-

ments. Use HDB3 unless AMI is required in your application .

Alternate Mark Inversion (AMI): AMI coding does not inherently

account for ones density. To meet this requirement, the user

should ensure that the data inherently meets pulse density

requirements.

3.0 CONFIGURATION

Two cards make up a single Model 2715RC G.703 Converter - a

front function card and a rear interface card. Each may require config-

uration depending upon the product application. This section describes

the location and orientation of the Model 2715RC’s configuration

switches and jumpers, and provides descriptions for all settings.

3.1 FRONT CARD CONFIGURATION

The Model 2715RC front card has a single bank of eight DIP

switches located on the top of the printed circuit board. Figure 1,

below, shows the position of the switches on the board.

Changing the DIP Switch Settings

Figure 2 shows the orientation of the DIP switches with respect to the

“ON” and “OFF” positions.

SWITCH SET SUMMARY TABLE

Position Function Factory Default Selected Option

SW1 Line Coding Off HDB3

SW2 CAS Multiframe Off Disabled

SW3 CRC-4 MF/Clock Mode Off Disabled

SW4 Clock Mode Off Network

SW5 DTE Rate Off

SW6 DTE Rate Off

SW7 DTE Rate Off

SW8 DTE Rate Off

2.048 Mbps

Clear

Channel

}

Figure 1. Model 2715RC board, showing DIP switch location

DIP Switch ON OFF

Figure 2. Close up of the configuration switches

NOTE: The ON position is oriented toward the front of the Model 2715RC.

ON OFF

Front Panel

Switch SW2: CAS Multiframe

CAS multiframe uses Timeslot 16 (TS16) to send multiframe (MF)

alignment data. In CAS MF, a multiframe is defined as 16 frames,

where a frame consists of 32 64kb/s timeslots, numbered 0 to 31.

TS16 of the first frame in the MF contains the CAS MF alignment word

in the upper four bits. The alignment word is always 0000 (binary). The

2715RC does not perform any signaling in TS16 other than to insert

the MF alignment word, in order to maintain MF alignment. When CAS

MF is disabled, the unit transmits user data in TS16; therefore, up to 31

channels are available for user data. When it is enabled, TS16 is not

available to the user. In this case, the user can use up to 30 channels

for data. CAS MF can be used with CRC-4 MF or by itself. When en-

nabled, both units must employ CAS MF; if one unit is set for CAS MF,

and the other is not, the one using CAS MF will detect a loss of sync.

SW2 Option

Off Disabled

On Enable

Switch SW3 & SW4: CRC-4 Multiframe/External Clock Mode

In framed mode, SW3 is used for CRC-4 MF. CRC-4 Multiframe

uses Time Slot zero to carry CRC-4 information. It operates independ-

ently of CAS MF. When CRC-4 is enabled, the unit monitors the incom-

ing data stream for CRC-4 errors. It transmits CRC-4 error counts to

the transmitting unit. Excessive errors may cause loss of frame or loss

of sync. If CRC-4 MF is used, both units must be set for set for CRC-4

MF. Otherwise, the one using CRC-4 MF will detect loss of sync.

In unframed mode, SW3 is used along with SW4 to determine

the clock mode. In unframed mode, the model 2715RC can be set to

Network, internal, or external clock mode.

In framed mode SW4 is used alone to determine the 2715RC

transmitter timing. In framed mode, the Model 2715RC can be set to

Network or Internal Clock Mode.

The following charts represent both cases.

CLOCK MODES

Network Clock Transmitter timing is derived from the received line

signal.

Internal Clock Transmitter clock is derived from an internal source

clock.

External Clock Transmitter timing is derived from the local DTE

device.

Note: When using the 2715RC as a high-speed short range modem,

one unit of the link must be configured in either internal or external

clock, and the other end must be configured for network clock mode.

Switches SW5, SW6, SW7, and SW8

Use Switches SW5, SW6, SW7, and SW8 to set the DTE data rate.

SW5 SW6 SW7 SW8 Speed

Off Off Off Off Clear Channel (2.048Mbps)1

On Off Off Off 64kbps

Off On Off Off 128kbps

On On Off Off 192kbps

Off Off On Off 256kbps

On Off On Off 384kbps

Off On On Off 512kbps

On On On Off 640kbps

Off Off Off On 768kbps

On Off Off On 1024kbps

Off On Off On 1280kbps

On On Off On 1536kbps

Off Off On On 1600kbps

On Off On On 1920kbps

Off On On On 1984kbps2

On On On On Invalid

UNFRAMED (G.703)

SW3 SW4 Clock Mode

Off Off Network (Default)

Off On Internal

On On External

On Off Network

MULTIFRAME(G.704)

SW3 CRC-4 MF SW4 Clock Mode

On On Off Network

Off Off On Internal