Patton electronics SmartNode 4400 Manuale utente

SmartNode 4400

IpChannel Bank

Quick Start Guide

Sales Ofﬁce: +1 (301) 975-1000

Technical Support: +1 (301) 975-1007

E-mail: [email protected]

WWW: www.patton.com

Part Number: 07MSN4400-QS, Rev. A

Revised: October 8, 2009

Important

This is a Class A device and is intended for use in a light industrial environment. It is not intended nor approved for use in an industrial

or residential environment.

Start Installation

For Quick

Start Installation

For Quick

Patton Electronics Company, Inc.

7622 Rickenbacker Drive

Gaithersburg, MD 20879 USA

Tel: +1 (301) 975-1000

Fax: +1 (301) 869-9293

Support: +1 (301) 975-1007

Web: www.patton.com

E-mail: [email protected]

Trademark Statement

The terms SmartNode,SmartWare, and SmartView are trademarks of Patton

Electronics Company. All other trademarks presented in this document are the prop-

erty of their respective owners.

The information in this document is subject to change without notice. Patton Elec-

tronics assumes no liability for errors that may appear in this document.

Important Information

To use virtual private network (VPN) and/or AES/DES/3DES encryption capabilities

with the SmartNode 4400, you may need to purchase additional licenses, hardware,

software, network connection, and/or service. Contact [email protected] or

+1 (301) 975-1000 for assistance.

Warranty Information

The software described in this document is furnished under a license and may be used

or copied only in accordance with the terms of such license. For information about the

license, go to www.patton.com.

Patton Electronics warrants all SmartNode router components to be free from defects,

and will—at our option—repair or replace the product should it fail within one year

from the ﬁrst date of the shipment.

This warranty is limited to defects in workmanship or materials, and does not cover

customer damage, abuse or unauthorized modiﬁcation. If the product fails to perform

as warranted, your sole recourse shall be repair or replacement as described above.

Under no condition shall Patton Electronics be liable for any damages incurred by the

use of this product. These damages include, but are not limited to, the following: lost

proﬁts, lost savings and incidental or consequential damages arising from the use of or

inability to use this product. Patton Electronics speciﬁcally disclaims all other warran-

ties, expressed or implied, and the installation or use of this product shall be deemed

an acceptance of these terms by the user.

Safety when working with electricity 3

SmartNode 4400 Quick Start Guide

Safety when working with electricity

The SmartNode contains no user serviceable parts. The equipment shall be

returned to Patton Electronics for repairs, or repaired by qualiﬁed service per-

sonnel. Opening the SmartNode case will void the warranty.

Mains Voltage: Do not open the case the when the power cord is attached.

Line voltages are present within the power supply when the power cords are

connected. The mains outlet that is utilized to power the device shall be

within 10 feet (3 meters) of the device, shall be easily accessible, and pro-

tected by a circuit breaker.

For AC powered units, ensure that the power cable used meets all applicable

standards for the country in which it is to be installed, and that it is connected

to a wall outlet which has earth ground.

The Model SN4400 is not shipped with power cables. For AC powered units,

ensure that the power cable used meets all applicable standards for the coun-

try in which it is to be installed, and that it is connected to a wall outlet which

has earth ground.

Hazardous network voltages are present in WAN ports regardless of whether

power to the SmartNode is ON or OFF. To avoid electric shock, use caution

when near WAN ports. When detaching the cables, detach the end away from

the SmartNode ﬁrst.

Because telephone line voltages can be dangerous, when detaching the net-

work cables, disconnect the end away from the SmartNode ﬁrst.

Do not work on the system or connect or disconnect cables during periods of

lightning activity.

In accordance with the requirements of council directive 2002/

96/EC on Waste of Electrical and Electronic Equipment (WEEE),

ensure that at end-of-life you separate this product from other

waste and scrap and deliver to the WEEE collection system in

your country for recycling.

WARNING

Introduction 4

SmartNode 4400 Quick Start Guide

Introduction

This Quick Start Guide leads you through the basic steps to set up a new SmartNode (see ﬁgure 1) and to

download a conﬁguration. Please note that this guide does not replace the detailed Software Conﬁguration

Guide and the Getting Started Guide on the CD-ROM and available online at www.patton.com/voip.

Figure 1. SmartNode 4400

SmartNodes can be used for a wide variety of IP and voice over IP applications. To support and ease the conﬁg-

uration of the SmartNodes, conﬁguration templates for the most important applications are available online at

http://www.patton.com/voip/appnotes.shtml.

Setting up a new SmartNode consists of the following steps:

1. Connect a PC to the SmartNode, log in and conﬁgure your LAN IP address (see page 5 for details)

2. Connect the SmartNode to the LAN (see page 7)

3. Download a conﬁguration example, adapt it to your network, and load it onto the SmartNode (see page 8)

Connecting a PC, logging in, and configuring the LAN IP address 5

SmartNode 4400 Quick Start Guide

Connecting a PC, logging in, and conﬁguring the LAN IP address

Connecting power and conﬁguring the default IP address

Connect the SmartNode to the mains power supply using the included power supply and cable. When the

RUN LED stops blinking and remains lit, the SmartNode is ready.

The factory default IP settings are listed in table 1. If these addresses do not work with your network they must

be changed. Contact your network administrator if you are not sure which IP address to use in

your installation.

Note The DHCP server is running on the ETH 0/1 of the SN4400 Series

models. All Ethernet ports are pre-conﬁgured and active.

Connecting to a PC and logging in

1. To access the SmartNode conﬁguration, connect a PC equipped with an RS-232 console port to the Con-

sole port on the front of the SmartNode. Use the included black Ethernet cable and RJ45 to DB-9 adapter

for this purpose (Model 16F-561).

Figure 2. Connecting to the PC

2. Open a Terminal connection to the SmartNode. Use the Terminal program included with most PC operat-

ing systems (e.g. Hyper Terminal on Windows). The CD-ROM also includes some recommended termi-

nal programs.

Table 1. Factory default IP address and network mask conﬁguration

Item IP Addresss(es) Network Mask

WAN interface Ethernet 0 (ETH 0/0) DHCP DHCP

LAN interface Ethernet 1 (ETH 0/1) 192.168.1.1 255.255.255.0

DHCP server address range 192.168.1.10-192.168.1.19 255.255.255.0

Console port

Laptop PC

Model 16F-561

adapter and cable

100-240V

(50-60 Hz)

1 AMP

UNITEQUIPPED WITH DUAL SUPPLIES

DISCONNECTBOTH SUPPLIES

BEFORESERVICING

ETH 0/0 Console TelcoPorts

Reset

ETH 0/1

Connecting a PC, logging in, and configuring the LAN IP address 6

SmartNode 4400 Quick Start Guide

3. Type administrator as the login prompt and press the Enter key after the password prompt (do not type

anything for the password). A prompt will appear consisting of the IP address and >character.

password:

172.16.40.1>

4. Following log in, the SmartNode is in operator execution mode (indicated by >character in the command

line prompt). With the commands enable and conﬁgure, you enter the conﬁguration mode.

172.16.40.1>enable

172.16.40.1#configure

172.16.40.1(cfg)#

Changing the IP address

1. Select the context IP mode to conﬁgure an IP interface.

172.16.40.1(cfg)#context ip router

172.16.40.1(ctx-ip)[router]#

2. Set the IP address and network mask for the each IP interface (eth0, for example).

Note For the examples in this guide, a private network (172.16.1) IP

address is used.

172.16.40.1(ctx-ip)[router]#interface eth0

172.16.40.1(if-ip)[eth0]#ipaddress 172.16.1.10 255.255.255.0

2002-10-29T00:09:40 : LOGINFO : Link down on interface eth0.

2002-10-29T00:09:40 : LOGINFO : Link up on interface eth0.

172.16.1.10(if-ip)[eth0]#

3. Make this modiﬁed conﬁguration your new start-up conﬁguration. On the next start-up the system will

initialize itself using the modiﬁed conﬁguration.

172.16.1.10 (if-ip)[eth0]#copy running-config startup-config

172.16.1.10 (if-ip)[eth0]#

Go to section “Connecting the SmartNode to the LAN” on page 7 to connect the SmartNode to

your network.

Connecting the SmartNode to the LAN 7

SmartNode 4400 Quick Start Guide

Connecting the SmartNode to the LAN

The 4400 Ethernet ports are auto MDX, therefore a straight-through wired cable can be used for host and

switch connections (see ﬁgure 3).

Figure 3. Connecting the SmartNode to the network

You can check the connection with the ping command to another host on the local LAN.

172.16.1.99(if-ip)[eth0]#ping <IP Address of the host>

Respectively from the host: ping 172.16.1.99

Note To ping outside your local LAN, you will need to conﬁgure the

default gateway.

You may now start to conﬁgure the SmartNode from scratch using the CLI commands, but we recommend

that you start your conﬁguration from a template. See “Downloading a conﬁguration example, adapting it to

your network, and loading it onto the SmartNode” on page 8 for further details.

For a detailed description of the CLI refer to the SmartWare Software Conﬁguration Guide (SCG) available on

the CD-ROM and online at: www.patton.com/voip.

UNITEQUIPPED WITH DUAL SUPPLIES

DISCONNECTBOTH SUPPLIES

BEFORESERVICING

ETH 0/0 Console TelcoPorts

Reset

ETH 0/1

LAN (ETH 0/1)

Network

interface

PC or workstation

or Telnet

LAN

Internet or

WAN (optional)

WAN

(ETH 0/0)

Downloading a configuration example, adapting it to your network, and loading it onto the SmartNode 8

SmartNode 4400 Quick Start Guide

Downloading a conﬁguration example, adapting it to your network,

and loading it onto the SmartNode

Patton provides a collection of conﬁguration templates on the CD-ROM that came with the SmartNode

device—and also on the support page at www.patton.com/voip/appnotes.shtml—one of which may be simi-

lar enough to your application that you can use it to speed up conﬁguring the SmartNode. Simply download

the conﬁguration note that matches your application to your PC. Adapt the conﬁguration as described in the

conﬁguration note to your network (remember to modify the IP address) and copy the modiﬁed conﬁguration

to a TFTP server. The SmartNode can now load its conﬁguration from this server.

Note Patton regularly adds new conﬁguration templates to the collection at

www.patton.com/voip/appnotes.shtml,so if you do not see your applica-

tion on the CD-ROM, it may have been added to the website.

Note If your application is unique and not covered by any of Patton’s conﬁgura-

tion templates, you can manually conﬁgure the SmartNode instead of load-

ing a conﬁguration ﬁle template. In that case, refer to the SmartNode Series

SmartWare Software Conﬁguration Guide for information on conﬁguring the

SmartNode device.

In this example we assume the TFTP server on the host with the IP address 172.16.1.11 and the conﬁguration

named SN.cfg in the root directory of the TFTP server.

172.16.1.99(if-ip)[eth0]#copy tftp://172.16.1.11/SN.cfg startup-config

Download...100%

172.16.1.99(if-ip)[eth0]#

After the SmartNode has been rebooted the new startup conﬁguration will be activated.

172.16.1.99(if-ip)[eth0]#reload

Running configuration has been changed.

Do you want to copy the 'running-config' to the 'startup-config'?

Press 'yes' to store, 'no' to drop changes : no

Press 'yes' to restart, 'no' to cancel : yes

The system is going down

Additional information

For detailed information about conﬁguring and operating guidance, set up procedures, and troubleshooting,

refer to the SmartNode Series SmartWare Software Conﬁguration Guide and the SmartNode Getting Started Guide

on the enclosed Patton VoIP CD-ROM or at http://www.patton.com/voip/. On the CD-ROM you will also

ﬁnd numerous freeware and shareware tools, including TFTP servers, Telnet clients, etc..

When you issue the reload command, the SmartNode will ask

if you want to copy the running conﬁguration to the startup con-

ﬁguration. Since you just downloaded a conﬁguration ﬁle to the

startup conﬁguration you must answer this question with NO.

Otherwise, the downloaded conﬁguration will be overwritten

and lost!

IMPORTANT

Compliance 9

SmartNode 4400 Quick Start Guide

Compliance

EMC compliance:

•FCC Part 15, Class A

•EN55022, Class A

•EN55024

•EN-61000-3-2 Harmonics

•EN-61000-3-3 Flicker

•EN-61000-4-2 ESD

•EN-61000-4-3 Radiated Immunity

•EN-61000-4-4 EFT

•EN-61000-4-5 Surge

•EN-61000-4-6 Low Frequency Common Immunity

•EN-61000-4-11 Voltage Dips and Sags

Safety compliance:

•UL60950-1/CSA C22.2 No. 60950-1

•IEC/EN 60950-1

•AS/NZS 60950-1

CE Declaration of Conformity

This equipment conforms to the requirements of Council Directive 1999/5/EC on the approximation of the

laws of the member states relating to Radio and Telecommunication Terminal Equipment and the mutual rec-

ognition of their conformity.

The safety advice in the documentation accompanying this product shall be obeyed. The conformity to the

above directive is indicated by CE sign on the device.

The signed Declaration of Conformity can be downloaded at www.patton.com/certiﬁcations.

Authorized European Representative

D R M Green

European Compliance Services Limited.

Avalon House, Marcham Road

Abingdon,

Oxon OX14 1UD, UK

NOTES 10

SmartNode 4400 Quick Start Guide

NOTES

Altri manuali per SmartNode 4400

Indice

Altri manuali Patton electronics Hardware di rete

Patton electronics

Patton electronics Diamond Edge 3224 Manuale utente

Patton electronics

Patton electronics Model 2604 Manuale utente

Patton electronics

Patton electronics 2888 Guida di riferimento

Patton electronics

Patton electronics 3002 Manuale utente

Patton electronics

Patton electronics ForeFront 2616RC Manuale utente

Patton electronics

Patton electronics NetLink 2720 Series Manuale utente

Patton electronics

Patton electronics NetLink 2701/B Manuale utente

Patton electronics

Patton electronics SMARTNODE 4900 Manuale utente

Patton electronics

Patton electronics ForeFront 2616RC Manuale utente

Patton electronics

Patton electronics 3095 Manuale utente

Patton electronics

Patton electronics NetLink 2720 Series Manuale utente

Patton electronics

Patton electronics Model 2711 Manuale utente

Patton electronics

Patton electronics FORESIGHT 6300 Manuale utente

Patton electronics

Patton electronics ACC-S02 Manuale utente

Patton electronics

Patton electronics NetLink 2707C Manuale utente

Patton electronics

Patton electronics OnSite 2884 Manuale utente

Patton electronics

Patton electronics RocketLink-G 3088/I Manuale utente

Patton electronics

Patton electronics Model 2604 Manuale utente

Patton electronics

Patton electronics 2450 Manuale utente

Patton electronics

Patton electronics 1090 Manuale utente

Patton electronics

Patton electronics 2715RC Manuale utente

Patton electronics

Patton electronics 3095 Manuale utente

Patton electronics

Patton electronics 3096RC Manuale utente

Patton electronics

Patton electronics NetLink 2960 RAS Manuale utente

Manuali Hardware di rete popolari di altre marche

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Manuale utente

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Manuale utente

Yudor

Yudor YDS-16 Manuale utente

D-Link

D-Link ShareCenter DNS-320L Manuale utente

Samsung

Samsung ES1642dc Istruzioni per l’uso

Honeywell Home

Honeywell Home LTEM-PV Istruzioni per il montaggio

evertz

evertz 7700 Series Manuale utente

D-Link

D-Link ShareCenter DNS-343 Manuale utente

Asante

Asante AsanteBridge 1012 Manuale utente

FireBrick

FireBrick FB2700 Manuale utente

Audiovox Electronics

Audiovox Electronics ARWH2T Manuale utente

ADC

ADC DSX-1 Manuale

NetComm

NetComm NF2 Manuale utente

Alcatel-Lucent

Alcatel-Lucent 5620 Manuale utente

Dell EMC

Dell EMC XC6420 Series Manuale utente

Lanner

Lanner NCA-1020A Manuale utente

Allied Telesis

Allied Telesis AT-TN121-A Manuale utente

Arista

Arista CCA-ETM-Q12 Manuale utente