Peak 440 Manuale
FOUR POST LIFT
Model: 440 440E
Original
Original
CONTENTS
Product Features and Specifications ...................................................... 1
Installation Requirement ..................................................................... 2
Steps of Installation ........................................................................... 4
Exploded View ...................................................................................29
Test Run .......................................................................................... 40
Operation Instruction ........................................................................ 42
Maintenance .................................................................................... 43
Trouble Shooting .............................................................................. 44
Lift Disposal..................................................................................... 44
1
I. PRODUCT FEATURES AND SPECIFICATIONS
●Electric-air control operation system.
●Mechanical self-lock and pneumatic safety release
●Manual hydraulic power system, cable-drived.
●Strengthen and Non-skid diamond platforms.
●Adjustable platform and adjustable safety lock ladders.
●Optional Jack:With Pneumatic hydraulic pump.
Model: 440 440E
MODEL SPECIFICATIONS
Model
Lifting
Capacity
Lifting
Height
Lifting
Time
Overall
Length
(Inc.
Ramps)
Overall
Width
Width
Between
Columns
Motor
440
18000kg
1905mm
176S
9300mm
4100mm
3654mm
2.0HP
430E
10800mm
Fig.1
2
II. INSTALLATION REQUIREMEN
A. TOOLS REQUIRED
Rotary Hammer Drill (Φ3/4)Carpenter’s Chalk
Hammer Screw Sets
Level Bar Tape Measure (295-1/4”)
English Spanner (12") Pliers
Wrench Set：
(10＃,12＃,13＃,14＃,17＃,19#,24＃,30#)Lock Wrench
Ratchet Spanner with Socket (28#)
Socket Head Wrench
(3#, 5#, 6#)
Fig. 2
3
B. Equipment storage and installation requirements.
The equipment should be stored or installed in a shady, normal temperature, ventilated and
dry place.
C. The equipment should be unload and transfer by forklift.
D. SPECIFICATIONS OF CONCRETE (See Fig. 4)
Specifications of concrete must be adhered to the specification as following.
Failure to do so may result in lift and/or vehicle falling.
1. Concrete must be thickness 120mm minimum and without reinforcing steel bars, and
must be dried completely before the installation.
2. Concrete must be in good condition and must be of test strength 210kg/cm2
minimum.
3. Floors must be level and no cracks.
D. AIR SUPPLY
Air pressure requirement: 0.5Mpa~0.8Mpa, Air line size Φ8 *Φ6.
E. POWER SUPPLY
The electrical source must be 4HP minimum. The source cable size must be 2.5mm² and in
good condition of contacting with floor. Single phase power unit connect fire, zero and
ground lines (Total 3 wires); 3 phase power unit connect fire, zero and ground lines (Total
5 wires).
√
Fig. 4
Concrete intensity must be 210kg/cm2minimum
≥120mm
Fig. 3
×
4
III. STEPS OF INSTALLATION
A. Location of installation
Check and insure the installation location (concrete, layout, space size etc.) is suitable for
lift installation.
B. Check the parts before assembly
1.Received lift with hydraulic power unit (See Fig. 5).
2. Open the outer packing, check all the parts according to the parts list (See Fig. 6).
3. Take off the Drive-in Ramps and Columns (See Fig.7).
4. Loose the screws of the upper package stand take off the offside platform take out
the parts inside the power side platform then remove the package stand.
Shipment Parts List
Parts box
Power-side Platform
Drive-in Ramp
Off-side Platform
Cross Beam
Column
Fig.6
Fig. 7
Fig. 5
Power unit
5
5. Move aside the parts and check the parts according to the shipment parts list (See Fig.
8).
6. Open the parts box and check the parts according to the parts box list
(See Fig. 9).
Fig. 9
Fig.8
43
6
7. Check the Parts bag according to the parts bag list (See Fig. 10).
Parts bag 1
Fig.10
7
C. Use a carpenter’s chalk line to establish installation layout, make sure the size is right and
base is flat (see Fig. 11).
Note: Reserve space before and behind the installation site.
Model
A
B
C
440
315 1/2″
(8014mm)
161 3/8″
(4100mm)
354 1/2″
(9002mm)
440E
374 1/2″
(9514mm)
161 3/8″
(4100mm)
407 7/8″
(10360mm)
B
A
C
Power-side column
Off-side column
Car in Direction
Use a carpenter’s chalk line to establish
installation layout
Fig. 11
8
D. Install cross beams (See Fig. 12).
E. Fix the anchor bolts
1. Prepare the anchor bolts (See Fig. 13).
2. Using the prescribed rotary hammer drill, and drill all the anchor holes and install the
anchor bolts, do not tighten the anchor bolts first (See Fig. 14).
Drilling
Clearing
Expand
1
3
2
3
5
110mm
Hole towards inside
Fig. 12
Fig. 13
Note: Minimum embedment of anchors is 110mm.
Fig. 14
Nut
Spring washer
Washer
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali Peak Sistema di sollevamento
Manuali Sistema di sollevamento popolari di altre marche
Genie
Genie Z-60/34 Manuale utente
Screen Technics
Screen Technics INTERFIT Vertical Up Lift Manuale utente
Mortuary Lift
Mortuary Lift ULTIMATE 1000 Manuale utente
Custom Equipment
Custom Equipment Hy-Brid 3 Series Manuale di programmazione
Custom Equipment
Custom Equipment Hy-Brid Lifts 2 Series Manuale di programmazione
Hy-Brid Lifts
Hy-Brid Lifts HB-P3.6 Manuale di programmazione
