peerless-AV LCZ-4F4G30B Guida
ISSUED: 04-05-11 SHEET #: 090-9201-4 (2013-10-03)
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com
Max Load Capacity per display: 19.8 lb (9 kg)
Installation and Assembly:
Quad Monitor Grommet for up to 24” Monitors
Models: LCZ-4F4G30B
2 of 26 ISSUED: 04-05-11 SHEET #: 090-9201-4 (2013-10-03)
NOTE: Read entire instruction sheet before you start installation and assembly.
Table of Contents
Parts List.................................................................................................................................................................................3
Installation of Base.................................................................................................................................................................4
Attaching Mounting Plates to Display.....................................................................................................................................7
WARNING
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
call Peerless customer care at 1-800-865-2112.
• This product should only be installed by someone of good mechanical aptitude, has experience with basic building
construction, and fully understands these instructions.
• Make sure that the supporting surface will safely support the combined load of the equipment and all attached
hardware and components.
• Never exceed the Maximum Load Capacity. See page one.
• Always use an assistant or mechanical lifting equipment to safely lift and position equipment.
• Tighten screws firmly, but do not overtighten. Overtightening can damage the items, greatly reducing their holding
power.
• Be sure to use designated fasteners and tools to assemble product. If correct fasteners and tools are not used,
product may fail.
3 of 26 ISSUED: 04-05-11 SHEET #: 090-9201-4 (2013-10-03)
Parts may appear slightly different than illustrated.
Before you begin, make sure all parts shown are included with your product.
Description Qt
y
Abase cover 1
Bpressure clamp 1
Cmounting bracket 4
Dpole 1
Elock collar 2
Fcrossbar 2
GM4 x 12mm screw 16
HM4 x 30mm screw 16
Ispacer 16
Jknob 4
Kcable clip 2
L3mm allen wrench 1
M4mm allen wrench 1
Parts List A
B
C
D
F
GH
E
KL
M
J
I
4 of 26 ISSUED: 04-05-11 SHEET #: 090-9201-4 (2013-10-03)
Base assembly can be attached to a mounting surface with a maximum thickness of 3-1/2" (90mm).
Set base (A) on mounting surface as shown in figure 1.1 and mark the center of the base. Drill a 3/8" (10mm) dia.
hole through mounting surface. OPTIONAL: Drill a 3/4" (19mm) dia. hole for cable management.
Remove base cover from base (A). Place base on mounting surface and secure using pressure clamp (B) as
shown in figure 1.2.
Hand tighten pole (D) onto base (A) as shown in figure 1.3. Tigthen set screw to secure pole using 3mm allen
wrench (L) as shown in rear view.
CABLE
MANAGEMENT
HOLE
1
Installation of Base
A
A
B
REAR VIEW
fig 1.1
fig 1.2 fig 1.3
SET SCREW
D
5 of 26 ISSUED: 04-05-11 SHEET #: 090-9201-4 (2013-10-03)
Feed cables through base cover. Insert base cover
onto pole (D). Insert lock collar (E) onto pole (D).
Adjust to desired height and tighten by hand.
BASE COVER
2 3
D
D
E
6 of 26 ISSUED: 04-05-11 SHEET #: 090-9201-4 (2013-10-03)
Insert crossbar (F) onto pole (D) and let it rest on lock collar (E) as shown in figure 4.1.
Adjust rotation of crossbar and hand tighten knob as shown in figure 4.2.
Repeat steps 3 and 4 for second lock collar (E) and crossbar (F).
4
D
E
F
4.1
fig 4.2
KNOB
CROSSBAR COVERS
CABLES
Cables may be routed through crossbar by removing crossbar covers.
5
7 of 26 ISSUED: 04-05-11 SHEET #: 090-9201-4 (2013-10-03)
Attaching Mounting Plates to Display
To prevent scratching the screen, set a cloth on a flat, level surface that will support the weight of the display. Place
display face side down. If display has knobs on the back, remove them to allow the mounting plates to be attached.
Place mounting plates (C) on back of display.
Choose hole pattern as shown in detail 1.
FOR DISPLAYS WITH FLAT BACKS: Attach mounting plates (C) to display using four 12mm screws (G) as shown
in figure 6.1.
FOR DISPLAYS WITH RECESSED BACKS: Attach mounting plates (C) to display using four 30mm screws (H)
and four spacers (I) as shown in figure 6.2.
• Tighten screws so mounting plates are firmly attached. Do not tighten with excessive force. Overtightening can
cause stress damage to screws, greatly reducing their holding power and possibly causing screw heads to become
detached. Tighten to 40 in. • lb (4.5 N.M.) maximum torque.
• If screws don't get three complete turns in the screen inserts or if screws bottom out and bracket is still not tightly
secured, damage may occur to screen or product may fail.
WARNING
VESA 100mm
VESA 75mm
VESA 75mm VESA 100mm
DETAIL 1
fig 6.1
fig 6.2
6
C
C
H
I
G
8 of 26 ISSUED: 04-05-11 SHEET #: 090-9201-4 (2013-10-03)
Hook mounting brackets (C) onto crossbar (F).
Adjust position of displays horizontally to desired location and install knobs (J) into rear of mounting brackets.
Knobs (J) may be tightened using 3mm allen wrench (L).
7
C
FJ
J
K
CABLES
Cables may be routed using cable clip (K).
8
PUBLICADO: 04-05-11 HOJA #: 090-9201-4 (2013-10-03)
2300 White Oak Circle • Aurora, Il 60502 • (800) 865-2112 • Fax: (800) 359-6500 • www.peerless-av.com
Instalación y ensamblaje:
Estante con ojete para cuatro monitores para monitores de
hasta 24"
Modelo: LCZ-4F4G30B
Capacidad máxima de soportar carga
por pantalla:19.8 lb (9kg)
Español
10 de 26 PUBLICADO: 04-05-11 HOJA #: 090-9201-4 (2013-10-03)
Tabla de contenido
Lista de piezas......................................................................................................................................................................11
Instalación de la base.......................................................................................................................................................... 12
Fijación de las placas de montaje en la pantalla................................................................................................................. 15
Nota: Lea la hoja de instrucciones completa antes de comenzar la instalación y el ensamblaje.
• No comience a instalar su producto de Peerless hasta haber leído y entendido las instrucciones y las advertencias
contenidas en la Hoja de Instalación. Si tiene alguna pregunta acerca de cualquiera de las instrucciones o las
advertencias, por favor, llame a Servicio al Cliente de Peerless al 1-800-865-2112 si está en EE. UU. Si es un
cliente internacional, por favor, comuníquese con su distribuidor local.
• Este producto sólo debe ser instalado por una persona que tenga una buena aptitud mecánica, que tenga
experiencia en construcción básica de edificios y que entienda estas instrucciones en su totalidad.
• Asegúrese de que la superficie de apoyo sostendrá, con seguridad, la carga combinada del equipo y todos los
fijadores y componentes.
• Nunca sobrepase la capacidad máxima de soportar carga aceptada. Vea la página 9.
• Siempre cuente con la ayuda de un asistente o utilice un equipo mecánico de izar para levantar y colocar el equipo
con más seguridad.
• Apriete los tornillos con firmeza, pero no en exceso. Apretarlos en exceso puede dañar los artículos y puede
disminuir significativamente su fuerza de fijación.
• Asegúrese de utilizar los sujetadores y las herramientas indicados para armar el producto. Si no utiliza los
sujetadores y las herramientas indicados, el producto podría fallar.
ADVERTENCIA
Indice
Lingue:
Altri manuali peerless-AV Supporto TV
peerless-AV
peerless-AV DS-MBZ647P Manuale utente
peerless-AV
peerless-AV ACC-DSV449-P Guida
peerless-AV
peerless-AV SmartMount SF680-AB Manuale utente
peerless-AV
peerless-AV DS-S555-4X3 Manuale utente
peerless-AV
peerless-AV WL-SR560M-300 Guida
peerless-AV
peerless-AV YBTLU Manuale utente
peerless-AV
peerless-AV PDW T XL Guida
peerless-AV
peerless-AV ACCXT200 Guida
peerless-AV
peerless-AV SR555M Manuale utente
peerless-AV
peerless-AV DS-VW765-POR Manuale utente
peerless-AV
peerless-AV tru-vue TRWS251/BK Manuale utente
peerless-AV
peerless-AV ACC-DSV240 Guida
peerless-AV
peerless-AV PLAV70-UNL-S Guida
peerless-AV
peerless-AV 8PEDSVW765LAND Manuale utente
peerless-AV
peerless-AV Designer SUA771PU Series Manuale utente
peerless-AV
peerless-AV CM850 Guida
peerless-AV
peerless-AV PF660 Manuale utente
peerless-AV
peerless-AV FS-MIS38426 Manuale utente
peerless-AV
peerless-AV SUT646P Manuale utente
peerless-AV
peerless-AV tru-vue TRWV110/BK Manuale utente
