perixx PERICAM-902 Manuale utente

Wireless Pan & Tilt
IP Surveillance Camera
Wireless Pan & Tilt Remote
Control /
Night Vision
Quick Installation Guide
PERICAM-902
Please nd the French, Italian, Spanish, and Portuguese User Manual in the CD

2
Wireless Pan & Tilt IP Surveillance Camera
1.1 PRODUCT ACCESSORIES INCLUDE
1.2 SYSTEM REQUIREMENT
1.IP-Camera
2.Power adaptor, 5V/ 1.5A Switching Power adaptor
3.Ethernet Cable(red), used to connect to the network card of PC for testing and configuring the
product
4.Ethernet Cable (blue), used to connect to Hub, ADSL modem, IP Share
5.Setup CD
6.This User’s Guide
7.Accessory for hanging and fastening
PC:
- Processor: Intel Pentium 4 ® 1.4GHz or above is recommended
- RAM: 256MB or above
- Operation System: Windows 2000® or Windows XP®
- Hard Disk: Minimum 100MB or above
- Read only CD-ROM (for IPCamFinder installation)
- Windows Media Play 9.0 or above
Network:
- Network Card: 10/100 baseT/TX Fast Ethernet
- Wireless Network : I EEE 802.11 b/g or higher
- Network Setup: Accessing Internet normally
- Web Browser: ActiveX Enabled and Compliant (Microsoft Internet Explorer 6.0 or above)
- Connect Network Equipment: ADSL modem, Wireless IP Share or Hub

3
Quick Installation Guide
1.3 EXTERIOR FUNCTION INTRODUCE
※ Usage of Reset Switch:
During system normal operation, press and hold the Reset Switch for a short time (approximately
8 seconds) until the front Status Light goes out, the system will restart and return to the factory
default settings.
※Power On description:
After inserting the included 5V/ 1.5A Switching Power adaptor into power outlet, you have to wait
for 40 seconds of power on time for IP Cam to confirm its software/hardware are normal. The Status
Light will light up and execute the motor homing action once power is on.
IR LED X 6 Focus
Adjustable
Status Light
DC JACK
Antenna
RJ-45 JACK
Reset Switch

4
Wireless Pan & Tilt IP Surveillance Camera
1.4 IP CAM FINDER
IP Cam Finder is the IP search application provided by this product. It can search all the IP CAMs
connected in LAN. Through sending out the inquiry of broadcasting packets and receiving responses
from IP CAMs, the window will display a list of all IP CAMs in the network. Furthermore, it also
provides modify functions for changing specified IP CAM’s network settings, e.g. IP Address change
function.
IPCamFinder tools in detail (Figure 1):
1.5 USE IP-CAM AND TEST THE IMAGE FUNCTION FOR THE FIRST TIME
※ The following connection is suitable for IP-CAM test/fixed IP address change/program code
update (strongly recommended).
The operation steps are listed below:
A. Installing the Product for the first time:
- Your computer must be equipped with network card and RJ-45 network connector.
- Connect the RJ-45 terminator on the rear of IP-CAM with the red test network cable. One end is
connected to the network card of computer; the other end is connected to the rear side of the
IP-CAM.
- Connect the power adaptor to the power port (on the rear) of IP-CAM. Now, the status LED on the
front of IP-CAM will light up.
IP CAM
List
MAC address
Display PC's
Ethernet network
card
Renew List
Choose the way
to get IP
Wireless mode
setting
Show IP
CAM
Renew
executed to
obtain an IP
Figure 1
IP address
Subnet Mask
Default
Gateway
PPPoE Setting

5
Quick Installation Guide
NOTEBOOK IP CAM
B. Check if the IP addresses for PC network and IPCamFinder are on the same network section:
- Usually, static IP address will be used to access into Internet, so the IP address will vary. When
you want to change IP address, please write down the original IP address on your computer
first. Then you have to modify the IP address of your computer for testing if the IP-CAM can be
operated normally . After finishing the test, IP address for your computer should be recovered to
original settings.
- In general, the IP address for your computer in LAN will be set with “Auto Obtain IP address”. To
test if the IP-CAM is normal, the IP address of your computer must be changed temporarily. After
finishing the test, it can be recovered to original settings.
C. Next, choose Control Panel->Network Connections->choose the activated area
Network Connections---> right click of your mouse --->select Properties(P)---> Select Internet
Protocol (TCP/IP)---> Select Properties(R) , then you can check the current IP address status for the
computer. The way to modify IP address is:
D. Open and execute IPCamFinder (as shown in Figure 2). The system will automatically scan the IP-
CAM that you just installed. Then, you will find 00:15:0F:00:00:22 192.168.1.100 in the column
of IP Cam List. Click 00:15:0F:00:00:22 192.168.1.100 with left mouse button. You can see the
default settings for IP-CAM.

6
Wireless Pan & Tilt IP Surveillance Camera
1.6 HOW TO SET UP IP CAM
Before you set up IP CAM, you have to know the network environment and if the IP address is fixed
or float that provided by your ISP. If you do not know, please contact with your ISP. To set up IP-CAM
and IP address, the common way that people use is to change the obtaining of IP address of IP-
CAM. Detailed information is listed as 1.7 .
1.7 SETTING THE WAY TO OBTAIN THE IP ADDRESS OF IP-CAM
1.7-1 STATIC - IP Address Setting
- You computer must be equipped with network card and RJ-45 network connector.
- Connect the RJ-45 terminator on the rear of IP-CAM to the red test network cable. One end is
connected to the network card of computer; the other end is connected to the rear side of the
IP-CAM.
- Connect the power adaptor to the power port (on the rear) of IP-CAM. Now, the status LED on the
front of IP-CAM will light up.
Step 1.
Select your PC’s Ethernet network card.
Step 2.
Click Find IP Cam with left mouse button, you with will see 00:15:0F:00:00:22 192.168.1.100
Step 3.
Click 00:15:0F:00:00:22 with left mouse button once, you will see following information
IP Address: 192.168.1.100
Net Mask : 255.255.255.0
GateWay : 192.168.1.1
Step 4.
Click Show IP Cam with left mouse button once which will start the Browser automatically. Login
using Username/Password into network monitor screen (refer to 3.1 for details). If you can see the
image screen, the IP-CAM is ready to use.
Figure 2
1. 2.
3.
3.
4.

7
Quick Installation Guide
NOTEBOOK IP CAM
- Open and execute IPCamFinder (as shown in Figure 3),The system will automatically scan the IP-
CAM that you just installed. Then, you will find 00:15:0F:00:00:22 192.168.1.100 in the column
of IP Cam List. Click 00:15:0F:00:00:22 192.168.1.100 with left mouse button. You can see the
default settings for IP-CAM.
Step 1.
Select your PC’s Ethernet network card.
Step 2.
Click Find IP Cam with left mouse button, you will see
00:15:0F:00:00:22 192.168.1.100 ….
Step 3.
Click 00:15:0F:00:00:22 with left mouse button once, you will see following information
IP Address: 192.168.1.100
Net Mask: 255.255.255.0
GateWay: 192.168.1.1
1. 2.
3.
3.
Figure 3

8
Wireless Pan & Tilt IP Surveillance Camera
Step 4.
Default connection mode selection is Manual, i.e. STATIC.
Step 5.
Type in Fixed IP.
IP Address : 211.78.174.94
Net Mask: 255.255.255.248
GateWay : 211.78.174.89
Step 6.
HTTP Port:Http communication port. The default setting is 80.
(If you have multiple IP-CAMs installed in the same network, you have to divide them with different
Port numbers, e.g, 1025、1026、1039…..)
Step 7.
After finishing the settings, click Setting to send. The network settings for this IP-CAM are renewed.
4.
5.
6. 7.
Figure 3
- Fill in Fixed IP Address as below. (If you do not know your fixed IP address, please contact with
your ISP. Below is an example of Fixed IP Address modification.)

9
Quick Installation Guide
Example:
1. Set up the IP CAM with fixed IP address.
2. Turn on your computer and open IE browser. Type 211.78.174.94:( 1025;1026;1039….) in the
Address line. Now you can access into the monitoring screen of network.
3. Key In Username: admin Password: password
1.8 LIVEVIEW
When using IP Cam for the first time, users must change the Internet Explorer security settings.
Otherwise, the system will display the following warning, and be unable to display the surveillance
images.
Step 1.
Following warning message is displayed on the screen.
Step 2.
Please click on the warning message with left mouse button and select Install ActiveX Control (C).
Step 3.
Select Install.
After successfully enabling and setting the IP CAM security parameters for the first time, no more
setup needed for the future operations.
1.8.1 The IE security settings can be changed by following the steps below:
Step 1.
IE Toolbar ---> Tools ---> Internet Options ---> Security ---> Custom Level …

10
Wireless Pan & Tilt IP Surveillance Camera
Step 2.
After clicking on Custom Level …, a security
settings window shall appear.
Change ActiveX Control Options and Plug-ins
settings to the following:
1.Download signed ActiveX controls: Enable
2.Download unsigned ActiveX controls: Enable
3.Initialize and script ActiveX controls not
marked as safe: Enable
4.Run ActiveX controls and plug-ins: Enable
5.Script ActiveX controls marked safe for
scripting: Enable
Altri manuali per PERICAM-902
1
Indice
Lingue:
Altri manuali perixx Telecamera IP


















