Perle JETSTREAM 8500 Guida rapida

Indice

Manuali Interruttore popolari di altre marche

URC

URC Total Control MFS-8 Manuale utente

Azbil

Azbil HPQ-D11 Manuale utente

Sony

Sony DFS-900M Manuale utente

SICK

SICK i17S Manuale utente

F&F

F&F SZR-277 Manuale utente

Shure

Shure UAMS/BK Manuale utente

Dräger

Dräger X-zone Switch Off Manuale utente

Asco

Asco Joucomatic 349 Series Manuale utente

BT

BT Mini Hub Manuale utente

D-Link

D-Link DES-1226G Manuale utente

Johnson Controls

Johnson Controls FS80-C Manuale utente

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Manuale utente

MicroNet

MicroNet SP1200A Manuale utente

Ruijie

Ruijie RG-PF2920 Series Manuale di installazione e funzionamento

Altinex

Altinex DA1914SX Manuale utente

MiLAN

MiLAN MIL-SM2401M Manuale utente

RJM

RJM MASTERMIND PBC/6X Manuale utente

Atlas

Atlas MMK-KVM8 Manuale utente

Perle

Perle 30th December 1998

Page 1of 2

Configuration of JETSTREAM 8500 & MTSRD for AIX 4.2

This is a quick installation guide for MTSRD on an AIX 4.2 system, to enable a login

on a terminal on a JETSTREAM 8500 port.

·Attach the JETSTREAM 8500 to the network and verify that it has an IP address,

broadcast address and subnet mask.

If not, add these using the following CLI commands, then reboot the

JETSTREAM.

set server internet 195.49.144.4

set server broadcast 195.49.144.255

set server subnet 255.255.255.0

save

·On the AIX system, add the JETSTREAM to the host table using smit, type:

smit

Then select ‘Communications Applications & Services’, ‘ TCPIP’,’ Further

Configuration’, ‘ Name Resolution’, ‘Hosts table’ ,’ Add a host’

·Install the mtsrd Software

cd /

installp -aX all

·Configure the JETSTREAM Ports

Log in to the JETSTREAM 8500 as admin, and type screen<cr>.

Use ‘network configuration’, ‘host table’, ‘add host’ and enter the AIX host

name and the TCP/IP address of this host to define the AIX host on the

JESTREAM.

Use ‘line configuration’ , ‘ line settings’ and select line 1

Set the service to SILENT RAW, enter the HOSTNAME of the AIX system

in the hostname field and set hostport to 10000

Set up further ports using hostport 10001 for line 2, hostport 10002 for line 3

and so on.

Perle

Perle 30th December 1998

Page 2of 2

·Update the /etc/mts/defaults file

Edit the file and change the MTS VERSION line to be:

MTS_VERSION JETSTREAM 8500 2.2.4 # JETSTREAM version

2.2.4 was our version of software; check the version you are using.

·Set up mtsrd ports on the AIX

Each JETSTREAM port must be configured on a different TCP port via smit,

type:

smit

Followed by selecting ‘Devices’, ‘ Communication’, ‘Specialix MTS’, ‘Add

Control Device’. Enter TCP/IP port number 10000.

Then ‘add a block of TTY ports’ with login set to enabled.

Attach a terminal to one of the JETSTREAM’s ports and you should see a

login.

Equipment used

JETSTREAM 8500 running version 2.2.4

WYSE 60 configured at 9600, 8 bit, 1stop, Np parity, Xon/Xoff flow control

AIX version 4.2.1