PhaseOne IXM-MV150F Manuale utente

iXM-MV150F/iXM-MV100 Camera Systems Installation Guide

Phase One

iXM-MV150F / IXM-MV100

Machine Vision Cameras

Installation Guide

This guide describes installation of your Phase One iXM-MV150F/iXM-MV100 camera system. As new features are

introduced via firmware updates, the downloadable version of this document changes accordingly. Downloads are

available HERE

iXM-MV150F/iXM-MV100 Camera Systems Installation Guide

Contents

1What’s in the Box?............................................................................................................ 4

2Camera Systems Overview ................................................................................................ 5

3Setting up the iXM-MV Camera ......................................................................................... 6

3.1 Exposure Sequence.................................................................................................... 6

3.1.1 Light Trigger Output Pulse for Global Reset (GR) Shutter Mode ............................. 6

3.2 Wiring a Control Cable for the iXM MV Camera.......................................................... 7

3.3 Understanding Black Reference ................................................................................. 8

3.4 Hardware Activation of Black Reference..................................................................... 9

3.5 Software Activation of Black Reference ...................................................................... 9

3.6 Wiring the Power Cable ........................................................................................... 10

3.7 Control Signal Electrical Interfaces ........................................................................... 11

4Preparing the Camera with Lens...................................................................................... 12

4.1 Mounting a Lens onto M72mm MV Interface ........................................................... 12

4.2 Dismounting a Lens from the M72mm Interface....................................................... 12

4.3 Removing the M72 Interface.................................................................................... 13

4.4 Attaching an SK Lens Adapter................................................................................... 14

4.5 Mounting a Lens onto an SK Lens Adapter................................................................ 15

4.6 Dismounting a Lens from an SK Lens Adapter. .......................................................... 17

5Connecting a camera ...................................................................................................... 18

5.1 Inserting iXM-MV Camera Control Cable to Data Terminal........................................ 18

5.2 Connecting Power Cable .......................................................................................... 18

5.3 Connecting a USB Cable ........................................................................................... 19

iXM-MV150F/iXM-MV100 Camera Systems Installation Guide

Page 3

5.4 Connecting the Strobe Light..................................................................................... 20

5.5 Connecting an HDMI Cable ...................................................................................... 20

6Camera Settings.............................................................................................................. 21

6.1 Storing Images ......................................................................................................... 23

6.1.1 Using XQD Cards ................................................................................................. 24

7Operating Phase One iXM-MV cameras using 10G........................................................... 25

7.1 Connecting a new camera to Capture One ............................................................... 25

7.2 Verifying a camera’s IP address ................................................................................ 26

7.3 Verified hardware for 10G networking ..................................................................... 27

7.4 Adapters.................................................................................................................. 27

7.5 SFP+ modules .......................................................................................................... 27

7.6 Media...................................................................................................................... 27

7.7 iXM 10G Port Cover ................................................................................................. 27

7.8 Configuring Jumbo Packets ...................................................................................... 28

8Firmware ........................................................................................................................ 31

8.1 Installing the Firmware Updater Application............................................................. 31

8.2 Updating the Firmware ............................................................................................ 31

8.3 Checking Firmware Version...................................................................................... 32

8.4 Restoring Firmware to Factory Version..................................................................... 32

9Interpreting the Camera LEDs ......................................................................................... 33

9.1 Temperature Warning ............................................................................................. 33

iXM-MV150F/iXM-MV100 Camera Systems Installation Guide

Page 4

1What’s in the Box?

The Standard Components below are included with the camera; the Optional Components can be purchased

separately.

Optional Components

Cables and Other Accessories

∙USB 3.1 (Gen.1) Shield Cable for iXM, 1m (P/N: 73233)

∙USB 3.1 (Gen.1) Shield Cable for iXM, 3m (P/N: 73235)

∙iXM Strobe Cable (3m) – Audio (P/N: 76002400)

∙M72 to modular focus adapter (P/N: 75048)

∙iXM to M72 Adapter (P/N: 75049)

∙iXM Heat Sink kit (P/N: 73217)

∙ iXM to MV Camera Tripod adapter (P/N: 75050)

∙IXM to SK Lenses adapter (P/N: 73201)

Lenses & Focusing Accessories

∙Inspec.x L 105mm f/5.6 float Lens (P/N: 73220)

∙Inspec.x L 105mm f/5.6 -1.0x Lens (P/N: 73211)

∙Inspec.x L 105mm f/5.6 -0.76x Lens (P/N: 73210)

∙Inspec.x L 105mm f/5.6 -0.5x Lens (P/N: 73214)

∙Inspec.x L 105mm f/5.6 -0.33x Lens (P/N: 73213)

∙Inspec.x L 100mm f/4 Lens (P/N: 73215)

∙Inspec.x L 60mm f/4 Lens (P/N: 73212)

∙Modular focus S (P/N: 75047)

∙Extension Tube M72 - M72, 24mm long (P/N: 75045)

∙Modular focus to 105mm Lens adapter (P/N: 75046)

iXM-MV150F/iXM-MV100 Camera Systems Installation Guide

Page 5

2Camera Systems Overview

1. Pod mounting threaded holes (four)

2. Lens secure screws (four)

17 M72 MV Interface

3. XQD card cover

4. XQD card cover screw

5. Storage LED

6. Operation LED

7. USB 3.1 port cover screw

8. USB 3.1 port cover

9. Data terminal A

10. Data terminal B

11. Power terminal

12. Power LED

13. Ethernet port cover screw

14. Ethernet port cover

15. HDMI port cover screw

16. HDMI port cover

17. M72 MV Interface

iXM-MV150F/iXM-MV100 Camera Systems Installation Guide

Page 6

3Setting up the iXM-MV Camera

3.1 Exposure Sequence

These signals control the iXM-MV150F/iXM-MV100 exposure sequence:

Hardware pulses

•Trigger in: Used for hardware triggering. It

signals the iXM-MV150F/iXM-MV100 to take

an image.

•System ready: Camera ready / busy output

signal. Returns to ‘high’ position shortly after

exposure (T3).

•Light Trigger Output: Signals the start and stop

of exposure. This pulse is software

configurable.

Delay Parameters for Global Reset (GR) Shutter Mode

(Software Configurable)

•D1: Delay time (-100us — +100us); Light trigger

pulse ON, to start integration (sensor reset).

•D2: Delay time (0 — +100us) Light trigger pulse

OFF, to start (sensor) readout.

3.1.1 Light Trigger Output Pulse for Global Reset (GR) Shutter Mode

The T2 and T3 trigger pulses can be software configured as follows:

•Single pulse active low: Starts exposure at signal ‘low’, stops exposure at signal

‘high’

Double pulse active low: Starts and stops exposure at signal ‘low’

Single pulse active high: Starts exposure at signal ‘high’, stops exposure at signal ‘low’

Double pulse active high: Starts and stops exposure at signal ‘high’

iXM-MV150F/iXM-MV100 Camera Systems Installation Guide

Page 7

Table 1: Exposure Sequence

3.2 Wiring a Control Cable for the iXM MV Camera

Table 2: Control Cable Wiring

Typical Values iXM MV100 iXM MV150F

Trigger IN

SysRdy (Low)

2 ms

SysRdy (Low)

2 ms

Trigger IN – Start exposure

30 ms 30 ms

Start Exp – End Exp

T2 + Exposure time T2 + Exposure time

Trigger IN – SysRdy High

(Cycle time)

12bit pixel depth:

290ms + Exposure time

14bit pixel depth:

390ms + Exposure time

16bit pixel depth:

800ms + Exposure time

12bit pixel depth:

390ms + Exposure time

14bit pixel depth:

520ms + Exposure time

16bit pixel depth:

1060ms + Exposure time

Pin Color Name Description Direction Level Notes

1 Orange Reserved Reserved Reserved Reserved Reserved

2 Green System Ready Camera ready for

next capture.

Out VOH, min = 4.0V

(Io = -10uA)

VOL, max = 0.8V

(Io = 4mA)

5 Volt Level Pull up

resistor

47.5K Ohms to +5 V

3 Red Black Reference

Control

Indicates a black

reference sequence

is required.

In VIH, min = 2.4V

VIL, max = 0.8VtiF,

tiR < 1uSec

Isolated. Active low.

See “Understanding

Black Reference” on

page 8

4 Purple Trigger In Trigger the

new capture cycle

In VIH, min = 2.4V

VIL, max = 0.8V

tiF, tiR < 1uSec

Active low.

(For manual triggering,

activate by short to

common signal,

otherwise leave floating)

5 Blue Reserved -- -- -- --

6 Yellow Reserved -- -- -- --

7 White Light Trigger

Pulse

Marks start and stop

of exposure

Out VOH min = 4.0V

(Io= -4mA)

VOL max = 0.8V

(Io= 4mA)

5 Volt Level

8 Gray Reserved Reserved In Short to pin 9

9 Black Common Common

iXM-MV150F/iXM-MV100 Camera Systems Installation Guide

Page 8

Table 3 – Camera Control Cable Description

Table 2 above, describes the functionality of the wires in the iXM-MV Camera control cable; the

figures below show the wire numbering order.

Figure 1: Control Cable Plug Pinout

Figure 2: Control Socket Pinout

3.3 Understanding Black Reference

A Black Reference is an on-site camera calibration for the current camera settings and environmental

conditions.

It is recommended to perform a new Black Reference calibration whenever you change the exposure time by

more than 100ms, or whenever the camera temperature changes by more than 100 C.

To perform a new Black Reference, take an image while the camera is not exposed to light (see details

below).

VIL Maximum voltage level that is interpreted as a ‘0’ by an input.

VIH Minimum voltage level that is interpreted as a ‘1’ by an input.

VOL Guaranteed maximum voltage level that appears on output set to ‘0’.

VOH Guaranteed minimum voltage level that appears on output set to ‘1’.

VIT+ Input threshold voltage when the input voltage is rising;

VIT - Input threshold voltage when the input voltage is falling.

iXM-MV150F/iXM-MV100 Camera Systems Installation Guide

Page 9

3.4 Hardware Activation of Black Reference

To activate black reference using Hardware line, keep the black reference control signal low during a full

capture cycle.

Figure 3: Black Reference Timing

3.5 Software Activation of Black Reference

Use the following table to determine the Black Reference mode to use for your capture flow:

Black Reference

Mode

Description

Black Ref:

Prerecorded Uses a Factory set black calibration. The camera uses this until the

user creates a Black reference for the current session.

Create Create and use a Black reference.

Black Ref. Create: This setting is for selecting when to create a Black reference image.

Use “Once” for non-digital lenses.

Once Performs a Back Calibration in the next capture cycle. If the Shutter

Mode is ‘ES’ make sure the camera is not exposed to light during next

capture.

Note: The Black reference is not saved after the camera is powered

down.

Always Performs black calibration for every capture.

Normal The iXM-MV camera creates a Black Reference when required.

iXM-MV150F/iXM-MV100 Camera Systems Installation Guide

Page 10

3.6 Wiring the Power Cable

The camera connects to the power bus with a power cable.

Figure 4: Power Cable Plug

Figure 5: Power Socket Pinouts

Note: Power the iXM-MV150F/iXM-MV100 cameras by a limited fused power source only, up to 8A

single fault condition.

Attention: La caméra iXM-MV150F/iXM-MV100 doit être alimentée par une source d’alimentation

protégée par un fusible, d’une capacité maximale de 8 Ampères.

Wire the power cable using the information in the table below.

Table 4: Power Cable Description

Connector

Color Name Description Direction Level Notes

1 White or yellow DC In + Provides positive power Input 12 - 30 V DC Provides up to 20

Watts

2 Black DC In - (Common) Input

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali PhaseOne Sistema di visione artificiale

PhaseOne

PhaseOne RP1 1600 Manuale utente

PhaseOne

PhaseOne PAS 280MP MK2 Manuale utente

Manuali Sistema di visione artificiale popolari di altre marche

Festo

Festo SBOC-M-R1B-H Manuale utente

Banner

Banner VE200G1B Manuale utente

SVS-Vistek

SVS-Vistek CoaxPress EoSens Creation 1.1CXP2 Manuale utente

Sony

Sony Vision Exchange PEQ-C100 Manuale utente

Datalogic

Datalogic MX-U81 Istruzioni per l'installazione

Cognex

Cognex In-Sight D900 Series Manuale utente

Spektrum

Spektrum SPMVR2520 Manuale utente

Huaray

Huaray Movidius Series Manuale utente

Daheng Imaging

Daheng Imaging MERCURY2 USB3 Manuale utente

SVS-Vistek

SVS-Vistek exo174 U3 Series Manuale utente

Teledyne

Teledyne e2v Eliixa+ Series Manuale utente

Photron

Photron FASTCAM Mini CX Series Manuale utente

National Instruments

National Instruments Vision CVS-1455 Manuale utente

Omron

Omron FH-L550 Manuale utente

iGen

iGen NV20/20 Manuale utente

JAI

JAI GO-5100MP-USB Manuale utente

Ark Vision Systems

Ark Vision Systems AVS-Monitor 7 FHD Manuale utente

Cognex

Cognex In-Sight 9902L Manuale utente

PhaseOne iXM-MV150F Manuale utente

Manuali Sistema di visione artificiale popolari di altre marche