Philio PAN03 Manuale utente

PAN03 ; PAN10

Switch Module with meter

Fig 1. PAN03 Assembling

Fig 2. PAN10 Assembling

This plug-in ON/OFF switch PAN03/PAN10 is a security enabled wireless switch,

based on -Wave Plus technology. -Wave PlusTM enabled devices displaying the -

Wave PlusTM logo can also be used with it regardless of the manufacturer, and can

also be used in other manufacturer’s -WaveTM enabled networks. Remote On/Off

control of the connected load is possible with other manufacturer’s wireless

Controller. Each switch is designed to act as a repeater. Repeaters will re-transmit

the RF signal to ensure that the signal is received by its intended destination by

routing the signal around obstacles and radio dead spots. Because PAN03/PAN10

supports Security Command Class, it can learn with Secured controller. Its

functionality and supported command classes is identical when included as a secure

and non-secure device.

This plug-in ON/OFF switch is able to detect instance wattage and overload current

(12A with resistive load) of connected lights or appliances. When detecting overload

state, the Switch will be disabled and its On/Off button will be lockout of which LED

will flash quickly. However, unplug and re-connect the switch will reset its overload

condition to normal status.

Adding to Z-WaveTM Network

In the front casing, there is an On/Off button with LED indicator which is used to

toggle switch on and off or carry out inclusion, exclusion, reset or association. When

first power is applied, its LED flashes on and off alternately and repeatedly at 0.5

second intervals. It implies that it has not been assigned a node ID and start auto

inclusion.

Auto nclusion

The function of auto inclusion will be executed as long as the switch does not have

Node ID and just plug the switch into a wall outlet.

Note: Auto inclusion timeout is 2 minute during which the node information of

explorer frame will be emitted once several seconds. Unlike “inclusion” function as

shown in the table below, the execution of auto inclusion is free from pressing the

On/Off button on the Switch.

The table below lists an operation summary of basic -Wave functions. Please refer

to the instructions for your -WaveTM Certificated Primary Controller to access the

Setup function, and to Add/Remove/associate devices

Function Description Annotation

No node ID The -Wave Controller does not allocate

a node ID to the Switch.

2-second on, 2-second off

Add

(Inclusion)

1. Put your -Wave controller into

inclusion mode by following the

instructions provided by the

controller manufacturer.

2. Pressing On/Off button three times

within 2 seconds will enter inclusion

mode.

Remove

(Exclusion)

1. Put your -Wave controller into

exclusion mode by following the

instructions provided by the

controller manufacturer.

2. Pressing On/Off button three times

within 2 seconds will enter exclusion

mode.

Node ID has been excluded. 0.5s On, 0.5s Off (Enter

auto inclusion)

Reset 1. Pressing On/Off button three times

within 2 seconds will enter inclusion

mode.

Use this procedure only in

the event that the primary

controller is lost or

otherwise inoperable.

2. Within 1 second, press On/Off

button again for 5 seconds.

3. IDs are excluded. 0.5s On, 0.5s Off (Enter

auto inclusion)

Association 1. The PAN03 is an always listening

-Wave device, so associations

may

be added or removed by a controller

at any time.

Or If your controller requires to have

the PAN03 send a 'node information

frame' or NIF for associations, then

pressing the On/Off button three

times within 2 seconds will cause

the PAN03 to send its NIF.

2. There are only one group for the

switch

Adding a node ID allocated by -Wave Controller means inclusion. Removing a node

ID allocated by -Wave Controller means exclusion.

Failed or success in including/excluding the node ID can be viewed from the -Wave

Controller.

Sometimes people are not easy to execute exclusion or inclusion especially when

PAN03 already installed in a wall box. To solve this issue, PAN03 support a special

feature that can use S1 or S2 to execute “exclusion, inclusion, Reset or Association”

at the first 3 minutes when first time connect to main power. PAN10 does not support

S1/S2 function.

LED ndication

To distinguish what mode the switch is in, view from the LED for identification.

State Type LED ndication

Normal Whenever we switch On and off of the PAN03/PAN10 by S1 S2 or

On/Off button or RF command, the LED will lights up 1 second

and then off.

No node ID Under normal operation, when the Switch has not been allocated a

node ID, the LED flashes on and off alternately at 2-second inter-

vals. By pressing S1 S2 or On/Off button, it will stop flashing tem-

porarily.

Learning When PAN03/PAN10 is in learning mode, LED flashes on and off

alternately and repeatedly at 0.5 second intervals.

Overload When overload state occurs, the Switch is disabled of which LED

flashes on and off alternately at 0.2 second intervals. Overload

state can be cleared by unplugging and reconnecting the Switch to

the wall outlet.

Choosing a Suitable Location

1. Do not locate the Switch facing direct sunlight, humid or dusty place.

2. The suitable ambient temperature for the Switch is 0°C~40°C.

3. Do not locate the Switch where exists combustible substances or any source of

heat, e.g. fires, radiators, boiler etc.

4. After putting it into use, the body of Switch will become a little bit hot of which

phenomenon is normal.

nstallation

1. Put the in wall switch into a wall box and connect the AC power wire L,N to

PAN03/PAN10 connector L, N.

2. Connect the wall switch to the PAN03/PAN10 as Fig1.

3. There are 3 mode PAN03/PAN10 can be configured to match different kind of

wall switch,

please refer to 3-10 Edge / Pulse / Edge-Toggle mode which described in next

section of this user manual.

Programming

1. Basic Command Class / Binary Switch Command Class

The Switch will respond to BASIC and BINARY commands that are part of the -

Wave system.

1-1 BASIC_GET / BINARY_SWITCH_GET

Upon receipt of the following commands from a -Wave Controller, the Switch will

report its On/Off state to the node asked.

Basic Get Command: [Command Class Basic, Basic Get]

Basic Report Command:

Report OFF: [Command Class Basic, Basic Report, Value = 0(0x00)]

Report ON:[Command Class Basic, Basic Report, Value = 255(0xFF)]

Binary Switch Get Command:[Command Class Switch Binary, Switch

Binary Get]

Binary Switch Report Command:

Report OFF:[Command Class Switch Binary, Switch Binary Report, Value

=0(0x00)]

Report ON:[Command Class Switch Binary, Switch Binary Report, Value

= 255(0xFF)]

1-2 BASIC_SET / SWITCH_BINARY_SET

Upon receipt of the following commands from a -Wave Controller, the load

attached to the Switch will turn on or off.

[Command Class Basic, Basic Set, Value = 1~99,255(0xFF)]: the load

attached to the Switch turns on.

[Command Class Basic, Basic Set, Value = 0(0x00)]: the load attached to

the Switch turns off.

[Command Class Switch Binary, Switch Binary Set, Value = 1~99,

(255)0xFF]: the load attached to the Switch turns on.

[Command Class Switch Binary, Switch Binary Set, Value = 0(0x00)]: the

load attached to the Switch turns off.

1. Z-Wave’s Groups (Association Command Class Version 2)

The Switch can be set to send reports to associated -Wave devices. It supports

one association group with one node support for Grouping 1. For group 1, the Switch

will report its latest status to -Wave Controller.

Grouping 1 includes, SWITCH_BINARY_REPORT, METER_REPORT,

ALARM_REPORT.

2-1 Auto report to Grouping 1 (Maximum Node 1)

2-1-1 On/Off Event Report

When “on” or “off” state has been changed, it will send Binary Switch Report to the

node of Grouping 1.

Binary Switch Report

ON:[Command Class Switch Binary, Switch Binary Report, Value

=255(0xFF)]

OFF:[Command Class Switch Binary, Switch Binary Report, Value

=0(0x00)]

2-1-2 Instant Power Consumption vary over 5% report

When the power consumption of load vary over 5%, it will send Meter report to the

nodes of Grouping 1.

Meter Report Command:

[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =

0x01，Precision = 1，Scale = 0x02，Size = 4，Meter Value(W) ]

2-1-3 Overload alarm report

When PAN03/PAN10 detects the current is more than 12A, it will send Alarm

Report to Group 1 node.

The content of Alarm Report

Alarm report command: [Command_Class_Alarm, Alarm_Report, Alarm Type = 0x08,

Alarm Level = 0xFF]

2-2 Response to Meter Get Command

The Switch will report its (1) instant Power Consumption (Watt) or (2) accumulated

power consumption(KWH) or (3) AC load Voltage (V) or (4) AC load current ( I )

(5) load power factor (PF) to -Wave Controller after receive the Meter Get

Command from -Wave Controller.

2-2-1 Instant Power Consumption (Watt) of Switch

When receiving Meter Get Command, it will report Meter Report Command to the

node.

Meter Get Command: [Command Class Meter, Meter Get, Scale =0x02(W)]

Meter Report Command:

[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =

0x01，Precision = 1，Scale = 0x02，Size = 4，Meter Value(W) ]

Example:

Meter Value 1 = 0x00 (W)

Meter Value 2 = 0x00 (W)

Meter Value 3 = 0x03 (W)

Meter Value 4 = 0xEA (W)

Meter(W) = Meter Value 3 *256 + Meter Value 4 = 100.2W

2-2-2 Accumulated Power Consumption (KW/h)

When receiving Meter Get Command, it will report Meter Report Command to

the node.

Meter Get Command: [Command Class Meter, Meter Get, Scale = 0x00 KW/h)]

Meter Report Command:

[Command Class Meter，Meter Report，Rate Type = 0x01 ，Meter Type =

0x01 ，Precision = 2，Scale = 0x00，Size = 4，Meter Value (KWh)]

Example:

Scale = 0x00 (KWh)

Precision = 2

Size = 4 Bytes (KW/h)

Meter Value 1 = 0x00(KWh)

Meter Value 2 = 0x01(KWh)

Meter Value 3 = 0x38(KWh)

Meter Value 4 = 0xA3(KWh)

Accumulated power consumption (KW/h) = (Meter Value 2*65536) + (Meter Value

3*256) + (Meter Value 4) = 800.35 (KW/h)

2-2-3 Clearing accumulated power consumption

Whenever re-start counting the accumulated power consumption is needed, you

can use Meter Reset Command to clear it.

Meter Reset Command: [Command Class Meter, Meter Reset]

2-2-4 AC load Voltage (V)

When receiving Meter Get Command, it will report Meter Report Command to the

node.

Meter Get Command: [Command Class Meter, Meter Get, Scale =0x04(V)]

Meter Report Command:

[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =

0x01，Precision = 1，Scale = 0x04，Size = 2 ，Meter Value(V)]

Example:

Scale = 0x04 (V)

Precision = 1

Size = 2 (2 Bytes of V)

Meter Value 1 = 0x09(V)

Meter Value 2 = 0x01(V)

AC load Voltage = (Meter Value 1*256) +(Meter Value 2)= 230.5 (V)

2-2-5 AC load current ( I )

When receiving Meter Get Command, it will report Meter Report Command to the

node.

Meter Get Command: [Command Class Meter, Meter Get, Scale =0x05( )]

Meter Report Command:

[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =

0x01，

Precision = 2，Scale = 0x05，Size = 2，Meter Value( )]

Example:

Scale = 0x05 (I)

Precision = 2

Size = 2 (2 Bytes of I)

Meter Value 1 = 0x01(I)

Meter Value 2 = 0x21(I)

AC load current = (Meter Value 1*256) +(Meter Value 2)= 2.89 (A)

2-2-6 load power factor (PF)

When receiving Meter Get Command, it will report Meter Report Command to the

node.

Meter Get Command: [Command Class Meter, Meter Get, Scale =0x06(PF)]

Meter Report Command:

[Command Class Meter，Meter Report，Rate Type = 0x01，Meter Type =

0x01 ，Precision = 2，Scale = 0x06，Size = 1 Bytes，Meter Value(PF)]

Example:

Scale = 0x06 (PF)

Precision = 2

Size = 1 (1 Byte of PF)

Meter Value 1 = 0x63(PF)

Load power factor (PF) = Meter Value 1 =0.99

3. Z-Wave’s Configuration

Configuration

Parameter

Function Size

(Byte)

Value Unit Default Description

1 Watt Meter

Report Period

2 0x01-

0x7FFF

5s 720 720*5s=3600s=1 hour

2 KWH Meter

Report Period

2 0x01-

0x7FFF

10min 6 6*10min=1 hour

3 Threshold of

current for Load

caution

2 10-1100 0.01A 1100 1100*0.01A = 11A

4 Threshold of

KWh for Load

caution

2 1-10000 1KWh 10000

5 Restore switch

state mode

1 0-2 1 0 : Switch off

1 : Last switch state

2 : Switch on

6 Manual On/Off

mode

1 0-1 1 0：Disable

manual On/Off

1：Enable

manual On/Off

7 LED indication 1 1-3 1 1 : Show switch state

mode 2 : Show night mode

3 : One flash mode

8 Auto off timer 2 0-0x7FFF 1s 0 0 : Disable auto off

function

1-0x7FFF : 1s ~

32767s

9 RF off com-

mand mode

1 0-3 0 0 : Switch off

1 : Ignore

2 : Switch toggle

3 : Switch on

10 Edge or Pulse

mode or

Edge-Toggle

mode

1 1-3 1 1：Edge mode

2：Pulse mode

3：Edge-Toggle mode

11 Manual Switch

Report mode

1 0-1 1 0 : Disable

1 : Enable

14 Watt differential

report mode

1 0-4 1 0 : Disable

1 : 5%

2 : 10%

3 : 15%

4 : 20%

3-1 Watt Meter Report Period:

If the setting is configured for 1hour (set value =720), the PAN03/PAN10 will report

its instant power consumption every 1 hour to Group1 node. The maximum

interval to report its instant power consumption is 45 hours

(5s*32767/3600=45hr).

3-2 KWH Meter Report Period:

If the setting is configured for 1hour (set value =6), the PAN03/PAN10 will report its

Accumulated Power Consumption (KW/h) every 1 hour to Group1 node. The

maximum interval to report its Accumulated Power Consumption (KW/h) is 227.55

days (10min*32767/1440=227.55 days).

3-3 Threshold of current for Load Caution

This is a warning when the current of load over the preset threshold value, if the

setting value is 1100, when the load current of Relay1 over this value,

PAN03/PAN10 will send current meter report to warn the Group1 node, the Range

of the setting value is from 10 to 1100, and the default value is 1100.

3-4 Threshold of KWh for Load Caution

This is a warning when the KWh of load over the preset threshold value, if the

setting value is 10000, when the Accumulated Power Consumption of Relay1

over this value, PAN03/PAN10 will send KWH meter report to warn the Group1

node, minimum value is 1KWh and default value is 10000 kWh.

3-5 Restore switch state mode:

Whenever the AC power return from lost, PAN03/PAN10 will restore the switch

state which could be SWITCH OFF、LAST SWITCH STATE、SWITCH ON. The

default setting is LAST SWITCH STATE.

3-6 Manual On/Off Mode:

The On/Off function of S1、S2 and learn switch can be disabled or enabled by this

parameter, default value is Enable. But the learning operation won’t be affected.

When manual On/Off function is disabled, the RF command can only switch On

but not Off. This is useful function for keeping the device in switch on state.

3-7 LED indication mode:

3-7-1 Show Switch State：When switch is on, LED is on. When switch is off, LED

is off. The default setting is Show Switch State.

3-7-2 Show Night mode：When switch is on, LED is off. When switch is off, LED

is on.

3-7-3 One Flash mode：When the state of switch changes, LED will be on only

one second, then LED keeps off.

3-8 Auto off timer：

Whenever PAN03/PAN10 switches to on, the auto off timer begin to count down.

After the timer decrease to zero, it will switch to off automatically. However if Auto

off timer is set as 0, the auto off function will be disabled. The default setting is 0.

3-9 RF off command mode

Whenever a switch off command, BASIC_SET、BINARY_SWITCH_SET、

SWITCH_ALL_OFF, is received, it could be interpreted as 4 variety of commands.

3-9-1 Switch Off：It switches to OFF state. The default setting is Switch Off.

3-9-2 Ignore：The switch off command will be ignored.

3-9-3 Switch Toggle：It switches to the inverse of current state.

3-9-4 Switch On：It switches to ON state.

3-10 Edge mode、Pulse mode and Edge-Toggle mode

Manual switch S1 and S2 can set to Edge mode or Pulse mode or Edge-Toggle

mode, default value is Edge mode. But this parameter is useless to PAN10.

3-10-1 Edge mode: this mode is suitable for the bi-stable wall switch that has indica-

tor point on the switch, and the same position correspond to same state of re-

lay1. If the PAN03/PAN10 relay change the state because of receiving -

Wave RF command, it may need two times of change (switch on to off or

switch off to on) to let relay back to the correspond state. Manual switch S2 is

disabled in this mode.

3-10-2 Pulse mode: this mode is suitable for the toggle type wall switch to swap the

state of Relay1.

3-10-3 Edge-Toggle mode: this mode is suitable for the normal bi-stable switch,

whenever change the state of the wall switch will also swap the state of Re-

lay1.

3-11 Manual Switch Report mode :

Whenever PAN03 is manually switch on or off, it will send BINARY_SWITCH_

REPORT to the node of group1. The default setting is Enable the function.

3-12 Watt differential report mode :

3-12-1 Disable : The function of Watt differential report will be disabled.

3-12-2 5% : When the differential value of Watt is over 5%, PAN03/PAN10 will send

a meter report to the associated group.

3-12-3 10% : When the differential value of Watt is over 10%, PAN03/PAN10 will

send a meter report to the associated group.

3-12-4 15% : When the differential value of Watt is over 15%, PAN03/PAN10 will

send a meter report to the associated group.

3-12-5 20% : When the differential value of Watt is over 20%, PAN03/PAN10 will

send a meter report to the associated group.

4. Protection Command Classes

PAN03/PAN10 supports Protection Command Class version 2, it can protect the

switch against unintentionally control by e.g. a child. And it can also protect the

switch from being turned off by setting it in “No RF Control” state.

After being set to “Protection by sequence” state, any intentional pressing of On/Off

button should be hold longer than 1 second, or the switch state will not change.

However, the operation of learn function does not change, because learning will not

be protected.

5. Firmware update over the air (OTA)

PAN03 is based on 500 series SoC and supports Firmware Update Command Class,

it can receives the updated firmware image sent by controller via the -wave RF me-

dia. It is a helpful and convenient way to improve some function if needed.

6. Command Classes

The Switch supports Command Classes including…

* COMMAND_CLASS_ WAVEPLUS_INFO

* COMMAND_CLASS_VERSION

* COMMAND_CLASS_MANUFACTURER_SPECIFIC_V2

* COMMAND_CLASS_SECURITY

* COMMAND_CLASS_DEVICE_RESET_LOCALLY

* COMMAND_CLASS_ASSOCIATION_V2

* COMMAND_CLASS_ASSOCIATION_GRP_INFO

* COMMAND_CLASS_POWERLEVEL

* COMMAND_CLASS_SWITCH_BINARY

* COMMAND_CLASS_BASIC

* COMMAND_CLASS_SWITCH_ALL

* COMMAND_CLASS_METER_V3

* COMMAND_CLASS_CONFIGURATION

* COMMAND_CLASS_ALARM

* COMMAND_CLASS_PROTECTION

* COMMAND_CLASS_FIRMWARE_UPDATE_MD_V2

Troubleshooting

Symptom Cause of Failure Recommendation

The Switch not working and

LED off

1. The Switch is not

plugged into the

1. Check power connections

2. Don’t open up the Switch and

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali Philio Unità di controllo

Philio

Philio PAN07-1C Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente