Philips GC4884/87 Manuale utente

GC4880 series

Question?

Contact

Philips

Question?

Contact

Philips

Specifications are subject to change without notice

4239 000 99791

User manual

Always there to help you

www.philips.com/welcome

3 4

GC4880 series

ENGLISH 6

DEUTSCH 12

NEDERLANDS 19

FRANÇAIS 26

6ENGLISH

Introduction

Congratulations on your purchase and welcome to Philips!

To fully beneﬁt from the support that Philips oers,

Product overview (Fig. 1)

1 Spray nozzle

2 Water ﬁlling door

3 Spray button

4 Steam slider

a. Dry setting ( )

b. ECO setting (ECO)

c. MAX setting ( )

5 Steam boost trigger

6 Safety auto-o light (speciﬁc types only)

7 Mains cord

8 Temperature indicator light

9 Water tank

10 Temperature dial

11 Calc clean button

12 Soleplate

13 Quick Calc Release lock

14 Quick Calc Release tray

15 Typeplate

Important

Read the separate important information leaet and this user

manual carefully before you use the appliance. Keep both

documents for future reference.

Using the appliance

Filling the water tank

Note: Your appliance has been designed to be used with

tap water. If you live in an area with hard water, fast scale

build-up may occur. Therefore, it is recommended to use

100% distilled or demineralized water to prolong the lifetime

of your appliance.

1 Open the water lling door.

2 Tilt the iron backwards and ll the water tank with tap

water up to the maximum level.

Note: Do not fill the water tank beyond the MAX indication.

Do not put perfume, vinegar, starch, descaling agents, ironing

aids or other chemicals in the water tank.

3 Close the water lling door ( ‘click’).

Temperature and steam setting

Table 1:

Warning: Do not use steam or steam boost at low

temperature, as indicated in the below table. Otherwise,

hot water may leak from the iron.

Fabric type Temperature

setting

Steam

setting

Steam

boost

Linen MAX / ECO Yes

Cotton ●●● Yes

Wool ●● ECO No

Silk ●● No

Synthetic

fabric (e.g.

acrylic, nylon,

polyamide,

polyester)

●No

1 Refer to Table 1 to set the temperature dial to the

appropriate setting for your garment.

2 Refer to Table 1 to set the appropriate steam setting for

your garment.

Note: Make sure that the steam setting you select is suitable

for the set ironing temperature.

3 Put the iron on its heel and plug it in. The temperature

light goes on to indicate that the iron is heating up.

4 When the temperature light goes out, the iron has reached

the correct temperature and you could start ironing.

ENGLISH 7

Features

Spray function

- Press the spray button to moisten the article to be ironed.

This helps to remove stubborn creases.

Steam boost function

- Use steam boost function at a temperature dial setting

between ●●● to MAX.

- Press and release the steam boost trigger for a powerful

boost of steam to remove stubborn creases.

Ironing with extra steam

- For extra steam during ironing, press and hold the steam

boost trigger.

Vertical steam

-You can use the steam boost function when you hold the

iron in vertical position for removing creases from hanging

clothes, curtains etc.

ECO steam setting / Dry ironing

- You could choose ECO setting in the steam slider to save

energy, yet to achieve satisfactory ironing results.

- To iron without steam, select dry setting in the steam slider.

ENGLISH8

Safety auto-o (specic types only)

The safety auto-o function automatically switches o the iron

if it has not been used for 30 seconds resting on its soleplate

or 8 minutes resting on its backplate. The auto-o light will

light up.

- To let the iron heat up again, pick up the iron or move it

slightly. The auto-o light goes out.

Cleaning and maintenance

Cleaning

1 Unplug the iron and let it cool down.

2 Pour any remaining water out of the water tank from the

water lling door.

3 Wipe akes and any other deposit o the soleplate with a

damp cloth and a non-abrasive (liquid) cleaning agent.

To keep the soleplate smooth, avoid hard contact with metal

objects. Never use a scouring pad, vinegar or other chemicals

to clean the soleplate.

Quick Calc Release

IMPORTANT: To prolong the life time of your appliance and

to maintain good steaming performance, use Quick Calc

Release function once every 1 month.

If water in your area is very hard, use this function more

frequently.

Note: Make sure that the iron has been unplugged for at

least 1 hour and has completely cooled down, before you use

Quick Calc Release.

1 Put the iron on a levelled surface and push up the Quick

Calc Release lock at the back of the iron.

2 Take out the Quick Calc Release tray.

3 Pour out scales in the tray into a sink or dustbin. Clean the

tray using tap water. Remove any excess water from the

tray.

ENGLISH 9

Do not pour water, vinegar, descaling agents or other chemicals

into the iron from the opening of the Quick Calc Release.

Do not use vinegar, descaling agents or other chemicals to

wash the tray.

4 Wipe o the scales in the opening of the Quick Calc

Release tray with a damp cloth.

5 Insert the tray back into the iron.

6 Push down the Quick Calc Release lock.

Do not use the iron when the Quick Calc Release tray is not locked.

If you break or lose the tray, contact a consumer care center

in your country (see the worldwide guarantee leaet for

contact details).

Calc-clean function

IMPORTANT: Besides Quick Calc Release function, you

should also perform calc-clean once every 1 month to

prolong the life of your iron. If water in your area is very

hard, or you see scales coming out from the soleplate during

ironing, use this function more frequently.

1 Make sure the iron is unplugged and the steam slider is set

to dry setting.

2 Fill the water tank to the MAX indication.

Do not pour vinegar or other descaling agents into the water tank.

3 Plug in the iron and set the temperature dial to MAX.

4 Unplug the iron when the temperature light goes out.

5 Hold the iron over the sink. Keep pushing the calc clean

button and gently shake the iron forth and back until all

water in the water tank has been used up.

Scales is ushed out, steam and boiling water also come out

of the soleplate.

Note: Repeat steps 2 to 5 if the water that comes out of the

iron still contains scale particles.

6 Take out the Quick Calc Release tray, empty the water in

the tray. Hold the iron vertically to allow small amount of

water to ow out.

7 Insert the tray back to the iron and lock it.

8 Plug in the iron and let the iron heat up to dry the soleplate.

9 Unplug the iron when the temperature indicator light goes out.

10 Move the iron gently over a piece of cloth to remove any

water stains on the soleplate.

ENGLISH10

Storage

1 Unplug the iron and empty the water tank. Let it cool

down in a safe place.

2 Wind the mains cord around the backplate of the iron and

store it on its heel.

Troubleshooting

This chapter summarises the most common problems you

could encounter with the appliance. If you are unable to solve

the problem with the information below, visit www.philips.com/

support for a list of frequently asked questions or contact the

Consumer Care Centre in your country (see the worldwide

guarantee leaet for contact details).

Problem Possible cause Solution

The steam boost

function does

not work properly

(water leaks out of

the soleplate).

You have used

the steam boost

function too often

within a very short

period.

Wait for a few seconds before you use the

steam boost function again.

You have used

the steam boost

function at a too low

temperature.

Set an ironing temperature at which the

steam boost function can be used (●●● to

MAX).

Flakes and

impurities

come out of the

soleplate during

ironing.

Scales are formed

inside the soleplate.

Use the Calc-clean function (see chapter

‘Cleaning and maintenance’, section ‘Calc-

clean function’).

Water leaks from

the water ﬁlling

door.

You have overﬁlled

the water tank.

Do not ﬁll the water tank beyond the MAX

indication. Pour excess water out of the

water tank.

Water or steam

leaks from the

back part of the

iron.

You have not

locked the Quick

Calc release tray

properly.

Take out the Quick Calc Release tray and

clean it using tap water. Use a piece of

cloth to wipe o scales in the opening of

the back part of the iron. Put back the tray

and lock it. (See chapter ‘Cleaning and

maintenance’, section ‘Quick calc release

function’).

The Quick Calc

release tray is

damaged.

Contact a consumer care center in your

country (see the world wide guarantee

leaet for contact details).

ENGLISH 11

12 DEUTSCH

Einführung

Herzlichen Glückwunsch zu Ihrem Kauf und willkommen bei

Philips! Um den vollständigen Support von Philips in Anspruch

nehmen zu können, müssen Sie Ihr Produkt unter www.philips.

com/welcome registrieren.

Produktübersicht (Abb. 1)

1 Sprühdüse

2 Füllabdeckung des Wasserbehälters

3 Sprühtaste

4 Dampfschieberegler

a. Trockeneinstellung ( )

b. ECO-Einstellung (ECO)

c. MAX-Einstellung ( )

5 Dampfstoßauslöser

6 Anzeige für die automatische Sicherheitsabschaltung

(nur bestimmte Gerätetypen)

7 Netzkabel

8 Temperaturanzeige

9 Wasserbehälter

10 Temperaturregler

11 Calc-Clean-Taste

12 Bügelsohle

13 Quick Calc Release-Verriegelung

14 Quick Calc Release-Einsatz

15 Typenschild

Wichtig!

Lesen Sie die separate Broschüre mit wichtigen Informationen und

diese Bedienungsanleitung sorgfältig durch, bevor Sie das Gerät

verwenden. Heben Sie beides zur späteren Verwendung auf.

Verwenden des Geräts

Den Wassertank füllen

Hinweis: Ihr Gerät wurde für die Verwendung mit

Leitungswasser entwickelt. Wenn Sie in einer Region mit

hartem Wasser leben, kann es schnell zu Kalkablagerungen

kommen. Daher wird empfohlen, 100 % destilliertes oder

demineralisiertes Wasser zu verwenden, um die Lebenszeit

Ihres Geräts zu verlängern.

1 Önen Sie die Füllabdeckung des Wasserbehälters.

2 Kippen Sie das Bügeleisen nach hinten, und füllen Sie den

Behälter bis zur oberen Markierung mit Leitungswasser.

Hinweis: Füllen Sie den Wasserbehälter nicht über die

Markierung MAX hinaus.

Questo manuale è adatto per i seguenti modelli

Indice

Lingue:

Altri manuali Philips Ferro

Philips

Philips Mistral GC2105 Manuale utente

Philips

Philips Azur Performer Plus GC4500 Series Manuale utente

Philips

Philips Double Speed GC6104 Manuale utente

Philips

Philips GC9500 Series Manuale utente

Philips

Philips Azur GC4310 Manuale utente

Philips

Philips Intellicare GC8080 Manuale utente

Philips

Philips GC9240 Manuale utente

Philips

Philips GC9140 Manuale utente

Philips

Philips GC7000 Series Manuale utente

Philips

Philips Powerlife GC2965/80 Manuale utente

Philips

Philips GC9200 Series Manuale utente

Philips

Philips 7400 Series Manuale utente

Philips

Philips GC4900 Manuale utente

Philips

Philips EcoCare GC3740/32 Manuale utente

Philips

Philips GC6103 Manuale utente

Philips

Philips HI 510 Manuale utente

Philips

Philips Azur Performer Plus GC4520/10 Manuale utente

Philips

Philips PerfectCare Aqua GC8620 Manuale utente

Philips

Philips GC3800 series Manuale utente

Philips

Philips GC4900 Manuale utente

Philips

Philips GC4525/10 Manuale utente

Philips

Philips PerfectCare Expert GC9500 Manuale utente

Philips

Philips FASTCARE COMPACT GC6700 Series Manuale utente

Philips

Philips GC1900 Manuale utente

Manuali Ferro popolari di altre marche

Clatronic

Clatronic DB 3703 Manuale utente

TEFAL

TEFAL FV4093Z0 Manuale utente

Gorenje

Gorenje SIH 2200 BS Manuale utente

Bosch

Bosch 2 Series Manuale utente

Riffel

Riffel Catena KB-819 Manuale utente

Texi

Texi Hestia Manuale utente

Maxwell

Maxwell MW-3010 Manuale utente

TREVIDEA

TREVIDEA Girmi ST60 Manuale utente

Primula

Primula Vapormat Manuale utente

Magio

Magio MG-541 Manuale utente

Scarlett

Scarlett SC-1334S Manuale utente

Bosch

Bosch Sensixx B22L Manuale utente

Vitek

Vitek VT-1247 VT Manuale utente

Cleanmaxx

Cleanmaxx 3397 Manuale utente

dyras

dyras ESI-2400AC Manuale utente

GE 169061 Manuale utente

Gorenje

Gorenje SIH 2200 GC Manuale utente

AEG

AEG DBS 5591 Manuale utente