Planet WAP-6200 Manuale utente

802.11g Wireless LAN Outdoor CPE AP

WAP-6200

Quick Installation Guide

Table of Contents

Package Content.............................................................................................. 3

Hardware Installation ....................................................................................... 4

Web Conguration .......................................................................................... 8

Further Conguration ....................................................................................... 8

Designed with the most innovative 802.11b/802.11g technology, WAP-6200

provides 54Mbps high data rate for outdoor environment. There are ve operating

modes supported in WAP-6200: AP, Client, WDS, AP+WDS, Repeater AP, Wireless

Client, Repeater, and Bridge. The multiple operation modes selection and built-

in 14dBi at panel antenna and default 200mW output power make WAP-6200 a

suitable CPE solution for widely open space applications such as WISPs, campuses,

and airports. Except for 64/128-bit WEP encryption, WAP-6200 integrates WPA,

WPA2 and 802.1x encryption to secure the information of your wireless LAN.

Package Content

WAP-6200 x 1

PoE injector x 1

Power Cord x 1

Mounting Kit x 1

CD-ROM x 1

Quick Installation Guide x 1

Note

If any of the above items are missing or damaged, contact your

local dealer for support.

Hardware Installation

Before you proceed with the installation, it is necessary that you have enough

information about WAP-6200.

1. Locate an optimum location and use the provided Mounting kit to tie the WAP-

6200 to a pole.

Note

For secured reason, while install the CPE AP, please be aware for

the electric wires around, and tighten the pole.

Without tighten the CPE AP, the pole and the installed site is with

electric wire around, there could be danger of being hurt by falling

or lethal injury.

2. Strongly suggest using SFTP cable (PLANET offers 25-meter SFTP cable, please

contact with local dealer for more information.) for waterproof and avoiding

thunder stroke, connect the RJ45 cable connector of the WAP-6200 to the

“P+DATA OUT” port of PoE Injector.

Note

Strongly suggest using SFTP cable, for better protection of the data

wire. 25-meter SFTP cable also available by order, the part no is

WL-SFTP-25. Please contact with local dealer for more information.

RJ45 CABLE

BACK COVER

FRONT COVER

CPE SET

POLE 1”-~1.5”

Mouting Kit

3. Be noticed, there are 2 ways for RJ45 cable connector avoiding water or thunder

stoke.

a. Stick and bind with rubber mastic tape on RJ45 cable connector after

connecting cable to “P+DATA OUT” port of PoE Injector.

b. After connecting cable to “P+DATA OUT” port of PoE Injector, open the Back

Cover and put the RJ45 cable connector inside of Back Cover, then plug the

Back Cover to CPE Set for preventing water.

4. Using Category 3 or higher UTP or STP cable, connect the “DATA IN” port of PoE

Injector to a 10Mbps or 10/100Mbps Ethernet hub or switch, and connect the PC

on the same LAN for management.

Note

To avoid thunder strike, consider to install ELA-100, thunder

arrester toward the CPE AP and the PoE injector.

5. Connect the power cord to the PoE Injector, and plug it into an AC outlet to

power on the WAP-6200.

Note

1. ONLY use the power adapter supplied with the WAP-6200.

Otherwise, the product may be damaged.

2. Strongly suggest using SFTP cable whether the cable exposed

outdoor for waterproof and avoiding thunder stroke.

RJ45 CABLE

BACK COVER

FRONT COVER

CPE SET

POLE 1”-~1.5”

Mouting Kit

OUTDOOR INSTALLATION WARNING

IMPORTANT SAFETY PRECAUTIONS:

LIVES MAY BE AT RISK! Carefully observe these instructions and any special

instructions that are included with the equipment you are installing.

CONTACTING POWER LINES CAN BE LETHAL.

Make sure no power lines are

anywhere where possible contact

can be made. Antennas, masts,

towers, guy wires or cables may

lean or fall and contact these limes.

People may be injured or killed if

they are touching or holding any

part of equipment when it contacts

electric lines. Make sure there is

NO possibility that equipment or

personnel can come in contact

directly or indirectly with power

lines.

Assume all overhead lines are power lines.

The horizontal distance from a tower, mast or antenna to the nearest power line

should be at least twice the total length of the mast/antenna combination. This will

ensure that the mast will not contact power if it falls either during installation or

later.

TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT

HEIGHTS ABOVE GROUND.

Select equipment locations that will allow safe, simple equipment installation.

Don’t work alone. A friend or co-worker can save your life if an accident

happens.

Use approved non-conducting lasers and other safety equipment. Make sure all

equipment is in good repair.

If a tower or mast begins falling, don’t attempt to catch it. Stand back and let

it fall.

If anything such as a wire or mast does come in contact with a power line,

DON’T TOUCH IT OR ATTEMPT TO MOVE IT. Instead, save your life by

calling the power company.

Don’t attempt to erect antennas or towers on windy days.

MAKE SURE ALL TOWERS AND MASTS ARE SECURELY GROUNDED, AND

ELECTRICAL CABLES CONNECTED TO ANTENNAS HAVE LIGHTNING

ARRESTORS. This will help prevent re damage or human injury in case of

lightning, static build-up, or short circuit within equipment connected to the

antenna.

The base of the antenna mast or tower must be connected directly to the

building protective ground or to one or more approved grounding rods, using 1

OAWG ground wire and corrosion-resistant connectors.

Refer to the National Electrical Code for grounding details.

IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER, AND

CANNOT MOVE:

DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED.

Use a non-conductive dry board, stick or rope to push or drag them so they no

longer are in contact with electrical power.

Once they are no longer contacting electrical power, administer CPR if you are

certied, and make sure that emergency medical aid has been requested.

Web Conguration

WAP-6200 provides a user friendly interface for users to congure via web browser.

Please follow the below steps to congure WAP-6200 basic settings.

1. It will take about 55 seconds to complete the boot up sequence after power on

from PoE.

2. Open your web browser and type WAP-6200 default IP address

(http://192.168.1.254) into the “Address Field” of you web browser. Before

conguration, please make sure your PC’s IP address is under the same IP range

with WAP-6200, such as 192.168.1.x.

3. After enter the IP address and press Enter key, you can see the login web page

without any username/password.

Further Conguration

For more settings of WAP-6200, please refer to the user’s manual in the CD. If you

have any difculty on resolving the problem while installing or using the device,

please feel free to contact your local dealer or PLANET Technical Support.

Indice

Altri manuali Planet Punto di accesso wireless

Planet

Planet WAP-6000 Manuale utente

Planet

Planet WDAP-C3000AX Manuale utente

Planet

Planet WDAP-C1800AX Manuale utente

Planet

Planet WDAP-C7200AC Manuale utente

Planet

Planet WAP-252N Manuale utente

Planet

Planet WNAP-6305 Manuale utente

Planet

Planet WAP-4060PE Manuale utente

Planet

Planet WDAP-850AC Manuale utente

Planet

Planet WDAP-C7200AC Manuale utente

Planet

Planet WDAP-W1200E Manuale utente

Planet

Planet WDAP-W7200AC Manuale utente

Planet

Planet IAP-2000PS Manuale utente

Planet

Planet WNAP-6306 Manuale utente

Planet

Planet WNAP-7300 Manuale utente

Planet

Planet WAPC-1232HP Manuale utente

Planet

Planet WNAP-1110 Manuale utente

Planet

Planet WDAP-C1750 Manuale utente

Planet

Planet WAP-4000A Manuale utente

Planet

Planet WAP-7500 Manuale utente

Planet

Planet EPN-402NV Manuale utente

Planet

Planet WAP-252N Manuale utente

Planet

Planet WNAP-6325 Manuale utente

Planet

Planet WAP-4036 Manuale utente

Planet

Planet WAP-4060PE Manuale utente

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente