Planet WAP-2000 Manuale utente

WAP-2000 User’s Guide

FCC Information

This equipment has been tested and found to comply with the limits for a Class A digital devices

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference when the equipment is operated in a commercial

environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause harmful interference to radio

communication.

Operation of this equipment in residential area is likely to cause harmful interference in which

case the user will be required to correct the interference at this own expense.

The user should not modify or change this equipment without written approval from company

name. Modification could void authority to use this equipment.

For the safety reason, people should not work in a situation which RF Exposure limits be

exceeded. To prevent the situation happening, people who work with the antenna should be

aware of the following rules:

1. Install the antenna in a location where a distance of 20 cm from the antenna may be

maintained.

2. While installing the antenna in the location, please do not turn on the power of wireless card.

3. While the device is working, please do not contact the antenna.

publication may be reproduced, adapted, stored in a retrieval system, translated into any

language, or transmitted in any form or by any means without the written permission of

PLANET, Inc.

Trademarks

WireFree and PLANET are trademarks of PLANET, Inc., all other trademarks throughout

this manual are the property of their respective companies.

Limited Warranty

In no event will PLANET be liable for any damage, including loss of data or profits, cost of

cover, or other incidental, consequential or indirect damages arising from the installation,

maintenance, use, performance, failure or interruption of PLANET’s products, whatever

caused and on any theory of liability. This limitation will apply even if PLANET has

been advised of the possibility of such damage.

CE Mark Warning

This is a Class A product. In a domestic environment, this product may cause radio interference,

in which case the user may be required to take adequate measures.

About This Manual

The purpose of this manual is for the setup of the 11Mbps Wireless LAN Access Point.

This manual, revised as version 1.0 in 2000, includes procedures assisting you in avoiding

unforeseen problems.

Revision

User’s guide for PLANET Wire Free Family –

For model: WAP-2000

Rev: 1.0 (July, 2000)

Part No.: EM-WAP2Kv1

Contents

Chapter 1 Introduction...................................................................................1

1-1 Features and Benefits................................................................................1

1-3 System Configurations...............................................................................3

Chapter 2 Hardware Installation...................................................................4

2-1 Product Kit................................................................................................4

2-2 System Requirements.................................................................................4

2-3 Mechanical Description.............................................................................5

Power Socket...............................................................................................................5

Ethernet Ports .............................................................................................................5

RS-232 Port (Console Port).........................................................................................6

2-4 Hardware Installation ...............................................................................6

Chapter 3 Configuring the Access Point........................................................7

3-1 Using the Access Point Manager...............................................................7

3-2 Using the Console Mode..........................................................................15

Chapter 4 Troubleshooting...........................................................................24

Appendix A Network Configuration...............................................................26

Appendix B Specifications...............................................................................29

Appendix C Glossary.......................................................................................30

-1-

Chapter 1 Introduction

The WAP-2000, 11Mbps Wireless LAN Access Point is a high-speed wireless unit that

performs as a transparent Media Access Control (MAC) bridge between wired Local Area

Networks, and one or more wireless networks. It brings Ethernet-like performance to the

wireless realm. Placed anywhere along an Ethernet LAN, the WAP-2000 allows wireless

stations in their coverage area to transparently access the corporate network. Fully

compliant with the IEEE802.11(b) standard, the 11Mbps Wireless LAN Access Point also

provides powerful features such as the Windows-based configuration utility, WEP security,

SNMP and more. The 11Mbps Wireless LAN Access Point enables you to build a variety of

network configurations.

1-1 Features and Benefits

lProtocol-independent networking functionality

lAccess for mobile users into the legacy wired Ethernet LAN.

lSeamless connectivity to wired Ethernet and PC network LAN’s augments existing

networks quickly and easily.

lSupports up to 11Mbps data rate: T-1 line alternative/replacement that

dramatically cuts costs.

lWireless connection without the hassles and cost of cabling.

lGreater flexibility to locate or move networked PC’s

-2-

1-2 Applications

The 11Mbps Wireless LAN products offer a fast, reliable, cost-effective solution for wireless

client access to the network in applications like these:

1. Remote access to corporate network information

E-mail, file transfer and terminal emulation.

2. Difficult-to-wireenvironments

Historical or old buildings, asbestos installations, and open area where wiring is

difficult to deploy.

3. Frequently changing environments

Retailers, manufacturers and those who frequently rearrange the workplace and

change location.

4. Temporary LANs for special projects or peak time

C1- Trade shows, exhibitions and construction sites where a temporary network will

be practical. C2- Retailers, airline and shipping companies need additional

workstations during peak period. C3- Auditors requiring workgroups at customer

sites.

5. Access to database for mobile workers

Doctors, nurses, retailers, accessing their database while being mobile in the hospital,

retail store or office campus.

6. SOHO (Small Office and Home Office) users

SOHO users need easy and quick installation of a small computer network.

7. High security connection

The secure wireless network can be installed quickly and provide flexibility. (Please

refer to page 18 for encryption configuration.)

-3-

1-3 System Configurations

The 11Mbp Wireless Access Point can be configured in a variety of network system

configurations.

Wireless Infrastructure

In a wireless infrastructure, the 11Mbps Access Point acts as a bridge. The Access Point

connects the wireless clients together. The Access Point acts as a center point for all

wireless communications. This would increase efficiency of the communications since the

wireless adapters do not need to be within direct range of each other.

Wireless Infrastructure with Stations Attaching to a Wired LAN

The 11Mbps Wireless LAN Access Point will provide access to a your local LAN. An

integrated wireless and wired LAN is called an Infrastructure configuration. A group of

wireless LAN PC users and anAccess Point construct a Basic Service Set (BSS). Each

wireless PC in this BSS can talk to any computer on your network via the Access Point.

-4-

Chapter 2Hardware Installation

This chapter describes initial setup of the Access Point.

2-1 Product Kit

Before installation, make sure that you the following items:

uThe 11Mbps Wireless LAN Access Point……………………x 1

uQuick Start Guide ……………………………….……………x 1

uPower Adapter……………………………………………..…..x 1

uManual…………………………………………………………x 1

If any of the above items are not included or damaged, please contact your local dealer for

support.

2-2 System Requirements

Installation of the 11Mbps Wireless LAN Access Point requires:

1. An AC power outlet (100~240V, 50~60Hz) which supplies the power for the Access

Point.

2. A 10/100 Base-T (UTP) Ethernet cable drop.

Note: (Only if you want to re-configure the WAP-2000 Access Point instead of using

factory default configuration…) A PC with an available RS-232C port runsthe

configuration program.

-5-

2-3 Mechanical Description

Top panel of the Access Point:

The following table provides an overview of each LED activity:

LED Definition Activity Description

PWR Continuous Green Power enabled

AP Continuous Green The Access Point is ready in service.

Off: No wireless activity

WLAN Flashing Green Flashing: Wireless RX/TX activity

Off: No Ethernet traffic activity

LAN Flashing Green Flashing: Wired LAN traffic activity

Off: no station connected to the Access Point

LINK Continuous Green On: with one or more stations associated to the

Access Point

Back panel of the Access Point:

Power Socket

The power adapter plugs into the socket labeled “POWER”.

Ethernet Ports

The 11Mbps Wireless LAN Access Point supports two types of Ethernet ports: RJ-45 MDI

daisy-chain port (labeled “MDI”) and RJ-45 MDI-X station port (labeled “MDI-X”). To

connect the Access Point to a hub, use the MDI port; to connect the Access Point to a

computer/station, use the MDI-X port. Both connection ports are used with a straight-

through UTP cable.Please note that, these two RJ-45 ports cannot be used at the same time.

The four LEDs (100M/Link/Tx/Rx) next to the Ethernet ports indicate the Ethernet physical

link status. The ‘Link’LED is a good indicator for to see if you have proper Ethernet

connection.

POWER MDI MDI-X RS-232

Link OR

100M TX

-6-

RS-232 Port (Console Port)

The RS-232 port is used for configuring the Access Point. Use a null-modem RS-232 cable

when you desire to configure the Access Point under console mode. See the section “Access

Point Console”on page 7 for detailed information.

2-4 Hardware Installation

Take the following steps to set up your Access Point.

nSite Selection

Before installation, determine the Access Point location. Proper placement of the Access

Point is critical to ensure optimum radio range and performance. You may use the Site

Survey and Access Points Browser utility (The utilities included with the wireless PC

Card) to choose a proper placement for your Access Point. Typically, the best location to

place your Access Point at your site is the center of your wireless coverage area. Try to

place your mobile stations within the line of sight. Obstructions may impede

performance of the Access Point.

nConnect the Ethernet Cable

The 11Mbps Wireless LAN Access Point supports 10/100M Ethernet connection.

Attach your UTP Ethernet cable to the RJ-45 connector on the Access Point. Then

connect the other end of the RJ-45 cable to a hub or a station. Please be aware that, use

the MDI port to connect the Access Point to a hub. Otherwise, please use the MDI-X

port to connect the Access Point to a computer/station.

nConnect the Power Cable

Connect the power adapter to the power socket on the Access Point, and plug the other

end of the power into an electrical outlet. The Access Point will be powered on and all

five indicators on the top panel will flash in sequence to test the functionality of the

indicators.

NOTE: ONLY use the power adapter supplied with the Access Point. Otherwise, the

product may be damaged.

Indice

Altri manuali Planet Punto di accesso wireless

Planet

Planet WAP-4033 Manuale utente

Planet

Planet WDAP-1750AC Manuale utente

Planet

Planet IAP-2000PS Manuale utente

Planet

Planet WDAP-3000AX Manuale utente

Planet

Planet 802.11n Wireless Access Point WNAP-1120 Manuale utente

Planet

Planet WNAP-3000PE Manuale utente

Planet

Planet WNAP-3000PE Manuale utente

Planet

Planet WNAP-6305 Manuale utente

Planet

Planet WDAP-C7200E Manuale utente

Planet

Planet WNAP-6350 Manuale utente

Planet

Planet IAP-1800AX Manuale utente

Planet

Planet WAP-252N Manuale utente

Planet

Planet WBS-202N Manuale utente

Planet

Planet WNAP-6350 Manuale utente

Planet

Planet WDAP-W7200AC Manuale utente

Planet

Planet WDAP-702AC Manuale utente

Planet

Planet WNAP-7205 Manuale utente

Planet

Planet WAP-6100 Manuale utente

Planet

Planet WAPC-1232HP Manuale utente

Planet

Planet WAP-900 Manuale utente

Planet

Planet WAP-8000 Manuale utente

Planet

Planet WAP-6000 Manuale utente

Planet

Planet WDAP-C1750 Manuale utente

Planet

Planet WNAP-6308 Manuale utente

Manuali Punto di accesso wireless popolari di altre marche

D-Link

D-Link DWL-2100AP - AirPlus Xtreme G Manuale utente

Ubiquiti

Ubiquiti NanoStation NSM2 Manuale utente

Cisco

Cisco Aironet 1550 Series Manuale utente

Aruba

Aruba IAP-335 Manuale utente

Advantek Networks

Advantek Networks AWN-AP-54MR Manuale utente

IP-COM

IP-COM AP355 Manuale utente

Buffalo

Buffalo AirStation WLA-L11G Manuale utente

EnGenius

EnGenius EnStationACv2 Manuale utente

D-Link

D-Link DAP-3662 Manuale utente

xG Technology

xG Technology xMax CN1300 Manuale utente

Widelink

Widelink ezWave WAP-1100 Series Manuale utente

Edimax

Edimax CAP1200 Manuale utente

Ubiquiti

Ubiquiti LBE-5AC-Gen2 Manuale utente

Aruba

Aruba AP-203R Manuale utente

LuXout Shades

LuXout Shades LUXSHADE MOTION Manuale utente

CreatComm

CreatComm TB5F Manuale utente

SineDigital

SineDigital MW-1500AP(H) Manuale utente

TP-Link

TP-Link AP9650 V1 Manuale utente