Planet WAP-8000 Manuale utente
802.11a/b/g Wireless LAN Outdoor AP
WAP-8000
Quick Installation Guide
Table of Contents
Package Content.............................................................................................. 4
Outlook........................................................................................................... 5
Hardware Installation ....................................................................................... 6
OUTDOOR INSTALLATION WARNING.................................................................. 8
Web Conguration .........................................................................................10
Further Conguration ......................................................................................11
Designed with Dual band 802.11a and 802.11b/g technology, WAP-8000 provides
108Mbps Super A+G mode high data rate for outdoor environment. There are four
operating modes supported in WAP-8000: AP, Bridge, AP Client and WISP. With
external N-type connector design and higher RF output power make WAP-8000 a
suitable CPE solution for widely open space applications such as WISPs, campuses,
and airports. Except for 64/128-bit WEP encryption, WAP-8000 integrates WPA,
WPA2 encryption to secure the information of your wireless LAN.
4
Package Content
WAP-8000 x 1
PoE injector x 1
Power Adapter x 1
Mounting Kit (with screw package) x 1
Weatherproof connector x 1
CD-ROM x 1
Quick Installation Guide x 1
Note
If any of the above items are missing or damaged, contact your
local dealer for support.
ó
ó
ó
ó
ó
ó
ó
5
Outlook
1. On the back panel of WAP-8000, there are LEDs indication
(LAN, WLAN, PWR).
2. On the bottom of WAP-8000, there are three interfaces.
(N-type antenna connector, Reset button, LAN port).
N-type
Antenna
connector
Reset
button
LAN
port
6
Hardware Installation
Before you proceed with the installation, it is necessary that you have enough
information about WAP-8000.
1. Plug in the waterproof connector on RJ-45 cable.
Step1 Step2
Note
Strongly suggest using SFTP cable, for better protection of the data
wire. 25-meter SFTP cable also available by order, the part no is
CB-STP-25. Please contact with local dealer for more information
2. Connect RJ-45 cable with the waterproof connector to the LAN port of WAP-8000
and another way connect to the “PoE” port of PoE Injector. Connect antenna to
N-type antenna connector.
Connect
antenna
3. Lock the waterproof connector into outside circle of the LAN port.
Step1 Step2
7
4. Locate an optimum location and use the provided Mounting kit to tie the WAP-
8000 to a pole.
Step3
Step1 Step2
Note
For secured reason, while install the CPE AP, please be aware for
the electric wires around, and tighten the pole.
Without tighten the CPE AP, the pole and the installed site is with
electric wire around, there could be danger of being hurt by falling
or lethal injury.
5. Connect the “LAN” port of PoE Injector to Ethernet hub, switch or PC on the
same LAN for management.
6. Connect the power adapter to the PoE Injector, and plug it into an AC outlet to
power on the WAP-8000.
Note
1. ONLY use the power adapter supplied with the WAP-8000. Other-
wise, the product may be damaged.
2. Strongly suggest using SFTP cable whether the cable exposed
outdoor for waterproof and avoiding thunder stroke.
8
OUTDOOR INSTALLATION WARNING
IMPORTANT SAFETY PRECAUTIONS:
LIVES MAY BE AT RISK! Carefully observe these instructions and any special
instructions that are included with the equipment you are installing.
CONTACTING POWER LINES CAN BE LETHAL.
Make sure no power lines are anywhere
where possible contact can be made.
Antennas, masts, towers, guy wires or
cables may lean or fall and contact these
limes. People may be injured or killed if
they are touching or holding any part
of equipment when it contacts electric
lines. Make sure there is NO possibility
that equipment or personnel can come in
contact directly or indirectly with power
lines.
Assume all overhead lines are power lines.
The horizontal distance from a tower, mast or antenna to the nearest power line
should be at least twice the total length of the mast/antenna combination. This will
ensure that the mast will not contact power if it falls either during installation or
later.
TO AVOID FALLING, USE SAFE PROCEDURES WHEN WORKING AT HEIGHTS
ABOVE GROUND.
Select equipment locations that will allow safe, simple equipment installation.
Don’t work alone. A friend or co-worker can save your life if an accident
happens.
Use approved non-conducting lasers and other safety equipment. Make sure all
equipment is in good repair.
If a tower or mast begins falling, don’t attempt to catch it. Stand back and let
it fall.
If anything such as a wire or mast does come in contact with a power line,
DON’T TOUCH IT OR ATTEMPT TO MOVE IT. Instead, save your life by
calling the power company.
Don’t attempt to erect antennas or towers on windy days.
ó
ó
ó
ó
ó
9
MAKE SURE ALL TOWERS AND MASTS ARE SECURELY GROUNDED, AND
ELECTRICAL CABLES CONNECTED TO ANTENNAS HAVE LIGHTNING
ARRESTORS. This will help prevent re damage or human injury in case of
lightning, static build-up, or short circuit within equipment connected to the
antenna.
The base of the antenna mast or tower must be connected directly to the
building protective ground or to one or more approved grounding rods, using 1
OAWG ground wire and corrosion-resistant connectors.
Refer to the National Electrical Code for grounding details.
IF A PERSON COMES IN CONTACT WITH ELECTRICAL POWER, AND
CANNOT MOVE:
DON’T TOUCH THAT PERSON, OR YOU MAY BE ELECTROCUTED.
Use a non-conductive dry board, stick or rope to push or drag them so they no
longer are in contact with electrical power.
Once they are no longer contacting electrical power, administer CPR if you are
certied, and make sure that emergency medical aid has been requested.
ó
ó
ó
ó
ó
ó
10
Web Conguration
WAP-8000 provides a user friendly interface for users to congure via web browser.
Please follow the below steps to congure WAP-8000 basic settings.
1. It will take a few seconds to complete the boot up sequence after power on
from PoE.
2. Before conguration of WAP-8000, please note that your PC’s IP address should
be on the same IP subnet (http://192.168.1.x) of the WAP-8000 (Please follow
the manual for assign a static IP address to set same IP subnet).
3. Open your web browser.
Default IP Address: http://192.168.1.1
Default IP subnet mask: 255.255.255.0
WEB login User Name / Password: admin
4. After enter the password, you can see the login web page.
Altri manuali per WAP-8000
1
Indice
Altri manuali Planet Punto di accesso wireless
Planet
Planet MAP-3100 Guida rapida
Planet
Planet WNAP-W2200 Manuale utente
Planet
Planet WAP-4035 Manuale utente
Planet
Planet WAP-4060PE Manuale utente
Planet
Planet WAP-6000 Manuale utente
Planet
Planet RTL8812AU-CG Manuale utente
Planet
Planet WAP-900 Manuale utente
Planet
Planet WDAP-C7200AC Manuale utente
Planet
Planet WDAP-C7200AC Manuale utente
Planet
Planet WNAP-7350 Manuale utente
Planet
Planet 802.11g Wireless Access Point / Bridge... Manuale utente
Planet
Planet WNAP-6350 Manuale utente
Planet
Planet WAP-2000 Manuale utente
Planet
Planet WDAP-C1800AX Manuale utente
Planet
Planet WDAP-3000AX Manuale utente
Planet
Planet WNAP-3000PE Manuale utente
Planet
Planet WNAP-7205 Manuale utente
Planet
Planet WDAP-C1750 Manuale utente
Planet
Planet WAP-6100 Manuale utente
Planet
Planet WAP-4033 Manuale utente
