Planet WDAP-W7200AC Manuale utente
1200Mbps 802.11ac Dual Band Wall-mount Wireless
Access Point
WDAP-W7200AC
Quick Installation Guide
Table of Contents
1. Package Contents ....................................................................................... 3
2. Hardware Description .................................................................................. 4
3. Hardware Installation .................................................................................. 5
3.1 Antenna Installation............................................................................. 5
3.2 Wall Mount Installation......................................................................... 6
3.3 DIN-Rail Mounting Installation .............................................................. 6
3.4 Magnet Installation .............................................................................. 8
3.5 Power on the Wireless AP..................................................................... 9
4. WiredNetworkConguration(Windows7) ...................................................10
5. Entering into the Web Management.............................................................11
6. Wireless Network Connection ......................................................................13
7. WDAP-W7200ACInstalledwithWirelessAPController...................................14
Further Information: .......................................................................................16
3
1. Package Contents
Thank you for choosing PLANET WDAP-W7200AC. Before installing the AP, please
verify the contents inside the package box.
The package should contain the following items:
WDAP-W7200AC 2.4GHz Antenna x 2
5GHz Antenna x 2
Quick Guide
DIN-rail Kit Magnet Kit Wall-mounted Kit
Note
If there is any item missing or damaged, please contact the seller
immediately.
4
2. Hardware Description
10/100/1000T
PoE
Reset
WDAP-W7200AC
5GHz 5GHz
2.4GHz 2.4GHz
5GHz
Antenna Connector
2.4GHz
Antenna Connector
PoE LAN Port
Reset Button
Power LED
Reset: Press and hold the button for more than 10 seconds to reset to the
factory default setting.
5
3. Hardware Installation
3.1 Antenna Installation
Step 1 Connect the 2.4GHz antennas to the RP-SMA connectors of the WDAP-
W7200ACthatindicates“2.4GHz” on the bottom panel.
2.4GHz 2.4GHz
2.4GHz
Step 2 Connect the 5GHz antennas to the RP-SMA connectors of the WDAP-
W7200ACthatindicates“5GHz” on the top panel.
5GHz5GHz
5GHz
6
3.2 Wall Mount Installation
Step 1 There are 4 holes with 8mm diameter on the wall; the distance between
the 2 holes is 133mm and the line through them must keep horizontal.
Step 2 Install a conductor pipe inside the board hole and ush the edge of the
conductor pipe with the wall surface.
Step 3 Screw the bolts into the conductor pipe. The WDAP-W7200AC is between
boltsandconductorpipe,asshownbelow.
5GHz 5GHz
10/100/1000T
PoE
Reset
WDAP-W7200AC
3.3 DIN-Rail Mounting Installation
The DIN-rail kit is included in the package. For the WDAP-W7200AC that needs to
beDIN-railmounted,pleaserefertothefollowinggures:
7
Step 1 ScrewtheDIN-railontheWDAP-W7200AC
5GHz 5GHz
Step 2 Lightly press the button of DIN-rail into the track
5GHz 5GHz
10/100/1000T
PoE
Reset
WDAP-W7200AC
1Push
2Click
8
Step 3 Check whether the DIN-rail is tightly on the track
5GHz 5GHz
10/100/1000T
PoE
Reset
WDAP-W7200AC
3.4 Magnet Installation
To install the WDAP-W7200AC on a magnetic surface, simply follow the diagram
below:
5GHz 5GHz
10/100/1000T
PoE
Reset
WDAP-W7200AC
9
3.5 Power on the Wireless AP
Step 1 Plug the Ethernet cable into the PoE port.
10/100/1000T
PoE
Reset
WDAP-W7200AC
Step 2 Plug the other end of the Ethernet cable into the PoE switch.
10/100/1000T
PoE
Reset
WDAP-W7200AC
802.3at PoE Switch
Power Requirement: 802.3at 30W
10
4.WiredNetworkConguration(Windows7)
A computer with wired Ethernet connection is required for the rst-time
congurationofthewirelessAP.
1. Click the “Start” button located on the lower-left corner of your computer.
2. Click “Control Panel”.
3. Double-click the “Network and Sharing Center” icon.
4. Click “Change Adapter Settings”.
5. Double-click “Local Area Connection”.
6. Select “Internet Protocol version 4 (TCP/IPv4)” and click “Properties”.
7.Select “Use the following IP address” and then click the “OK” button twice
to save the conguration. For example, as the default IP address of the WDAP-
W7200AC is 192.168.1.253 and the router is 192.168.1.254, you may choose
from 192.168.1.1 to 192.168.1.252.
Indice
Altri manuali Planet Punto di accesso wireless
Planet
Planet WNAP-1110 Manuale utente
Planet
Planet WNAP-7300 Manuale utente
Planet
Planet WNAP-6306 Manuale utente
Planet
Planet WNAP-6308 Manuale utente
Planet
Planet WAP-1965 Manuale utente
Planet
Planet Network Device WAP-4033PE Manuale utente
Planet
Planet WDAP-850AC Manuale utente
Planet
Planet WDAP-3000AX Manuale utente
Planet
Planet WDAP-1750AC Manuale utente
Planet
Planet WAP-4035 Manuale utente
Planet
Planet WAP-4030A Manuale utente
Planet
Planet WNAP-3000PE Manuale utente
Planet
Planet WDAP-C1800AX Manuale utente
Planet
Planet RTL8812AU-CG Manuale utente
Planet
Planet WDAP-C1750 Manuale utente
Planet
Planet WAP-6200 Manuale utente
Planet
Planet WDAP-C7210E Manuale utente
Planet
Planet WDAP-802AC Manuale utente
Planet
Planet WNAP-6350 Manuale utente
Planet
Planet WNAP-6350 Manuale utente
