Polaris PAC PAGAUT Manuale utente

H0770000_REVB

Above-Ground

Pool Automation Control

PAGAUT

Owner’s Manual

English | Français | Español

WARNING

FOR YOUR SAFETY - This product must be installed by a qualied pool professional or personnel who are

knowledgeable with the standards and code requirements for above ground pool equipment. The maintainer

must be a qualied pool professional or personnel with su󰀩cient experience in pool equipment installation and

maintenance so that all of the instructions in this manual can be followed exactly.

Improper installation and/or operation may result in death, serious injury or property damage. DO NOT MODIFY

THIS EQUIPMENT.

Before installing this product, read and follow all warning notices and instructions that accompany

this product. Failure to follow warning notices and instructions may result in death, serious injury

or property damage. Consult Polaris customer service at 1-800-822-7933 for assistance. Improper

installation and/or operation may void the warranty.

ENGLISH Polaris® PAC™Pool Automation Control |Owner’s Manual

Page 2

Table of Contents

Section 1. Important Safety Instructions...................................................................................................3

Section 2. System Overview.......................................................................................................................5

2.1 Package Contents..................................................................................................................................... 5

2.2 Electrical Specications ............................................................................................................................ 5

2.3 Materials and Tools ................................................................................................................................... 5

Section 3. Install Controller Box ................................................................................................................5

3.1 Mount the Controller Enclosure ................................................................................................................ 5

3.2 Bonding the Power Center ........................................................................................................................ 6

Section 4. High Voltage Plug In..................................................................................................................6

4.1 Plug In Assignment ................................................................................................................................... 6

Section 5. Low Voltage Wiring....................................................................................................................6

5.1 Wire the Temperature Sensors ................................................................................................................. 6

5.2 Install the Water Temperature Sensor....................................................................................................... 6

5.3 Install a Solar Sensor (if applicable) ......................................................................................................... 7

5.4 Install Additional Low Voltage Equipment (i.e., Heater Connection) ......................................................... 7

5.5 Install iAquaLink™ (if applicable) ............................................................................................................... 7

5.6 Mount the iAquaLink Device ..................................................................................................................... 7

5.7 Wire the iAquaLink Device ........................................................................................................................ 7

5.8 Install Jandy Valve® Actuators (JVAs) (if applicable) ................................................................................. 7

Section 6. User Interface.............................................................................................................................7

6.1 Navigation Buttons .................................................................................................................................... 7

Section 7. Install Settings ...........................................................................................................................8

7.1 Freeze Protect .......................................................................................................................................... 8

7.2 Units .......................................................................................................................................................... 9

7.3 Languages ................................................................................................................................................ 9

7.4 Clear Memory ........................................................................................................................................... 9

7.5 Color Lights ............................................................................................................................................... 9

7.6 Label Auxiliary Functions ........................................................................................................................ 10

7.7 Temp Calibrate ........................................................................................................................................ 10

7.8 Solar Priority (if applicable) ..................................................................................................................... 10

7.9 Assign JVA .............................................................................................................................................. 10

7.10 Diagnostics ..............................................................................................................................................11

Section 8. Main Menu ................................................................................................................................12

8.1 Equipment Status.................................................................................................................................... 12

8.2 Filter Pump .............................................................................................................................................. 12

8.3 Pool Heater On/O󰀨 ................................................................................................................................. 12

8.4 Turn Aux1, Aux2 or Aux3 On/O󰀨 ............................................................................................................ 12

8.5 Turn Specic Equipment On/O󰀨 Manually .............................................................................................. 13

8.6 Turn All Equipment O󰀨 ............................................................................................................................ 14

Section 9. Pool Only System Menu Flow Diagrams ...............................................................................15

9.1 Main Menu .............................................................................................................................................. 15

9.2 Install Settings Menu............................................................................................................................... 16

Section 10. Glossaries ................................................................................................................................17

10.1 Glossary of Safety Delays and Lockouts ................................................................................................ 17

10.2 Glossary of Alert Messages .................................................................................................................... 17

Section 11. Wiring Diagram ........................................................................................................................18

FCC Regulatory Compliance Statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and

2. This device must accept any interference received, including interference that may cause undesired operation/

CAUTION: Changes or modifications not expressly approved by the party responsible for compliance may void the user's

authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the

FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the

following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit di󰀨erent from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

ENGLISH

Polaris® PAC™Pool Automation Control |Owner’s Manual Page 3

Section 1. Important Safety Instructions

READ AND FOLLOW ALL INSTRUCTIONS

All electrical work must be performed by a licensed electrician and conform to all national, state, and local codes. When

installing and using this electrical equipment, basic safety precautions should always be followed, including the following:

DANGER

To reduce the risk of severe injury or death, do not remove the suction ttings of your spa or hot tub. Never operate

a spa or hot tub if the suction ttings are broken or missing. Never replace a suction tting with one rated less than

the ow rate marked on the equipment assembly.

WARNING

Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs when the internal

temperature of the body reaches a level several degrees above the normal body temperature of 98.6°F

(37°C). The symptoms of hyperthermia include dizziness, fainting, drowsiness, lethargy, and an increase in the

internal temperature of the body. The e󰀨ects of hyperthermia include: 1) unawareness of impending danger;

2) failure to perceive heat; 3) failure to recognize the need to exit spa; 4) physical inability to exit spa; 5) fetal

damage in pregnant women; 6) unconsciousness resulting in a danger of drowning. The use of alcohol, drugs,

or medication can greatly increase the risk of fatal hyperthermia.

WARNING

To Reduce the Risk of Injury

a) The water in a spa should never exceed 104°F (40°C). Water temperatures between 100°F (38°C) and

104°F (40°C) are considered safe for a healthy adult. Lower water temperatures are recommended for

young children and when spa use exceeds 10 minutes.

b) Since excessive water temperatures have a high potential for causing fetal damage during the early

months of pregnancy, pregnant or possibly pregnant women consult a physician before using a spa or

hot tub, and should limit spa water temperatures to 100°F (38°C). Water temperature in excess of 100°F

(38°C) may be injurious to your health.

c) Before entering a spa or hot tub, the user should measure the water temperature with an accurate

thermometer since the tolerance of water temperature-regulating devices varies.

d) The use of alcohol, drugs, or medication before or during spa or hot tub use may lead to unconsciousness

with the possibility of drowning.

e) Obese persons and persons with a history of heart disease, low or high blood pressure, circulatory system

problems, or diabetes should consult a physician before using a spa.

f) Persons using medication should consult a physician before using a spa or hot tub since some medication

may induce drowsiness while other medication may a󰀨ect heart rate, blood pressure, and circulation.

WARNING

Risk of electric shock which could result in severe injury or death - Install the controller at least 2 ft.

(0.6m) vertically o󰀨 the ground and ve (5) feet (1.52 m) from the inside wall of the pool and/or hot tub using

non-metallic plumbing so children cannot use the equipment to access the pool and be injured or drown.

Canadian installations must be at least three (3) meters from the water.

PREVENT CHILD DROWNING: Do not let anyone, especially small children, sit, step, lean or climb on any

equipment installed as part of your pool’s operational system.

Children should not use spas or hot tubs without adult supervision.

Do not use spas or hot tubs unless all suction guards are installed to prevent body and hair entrapment.

People using medications and/or having an adverse medical history should consult a physician before using a

spa or hot tub.

WARNING

To avoid injury ensure that you use this control system to control only packaged pool/spa heaters which have

built-in operating and high limit controls to limit water temperature for pool/spa applications. This device should

not be relied upon as a safety limit control.

ENGLISH Polaris® PAC™Pool Automation Control |Owner’s Manual

Page 4

Attention Installer: Install to provide drainage of compartment for electrical components.

SAVE THESE INSTRUCTIONS

WARNING

People with infectious diseases should not use a spa or hot tub.

To avoid injury, exercise care when entering or exiting the spa or hot tub.

Do not use drugs or alcohol before or during the use of a spa or hot tub to avoid unconsciousness and possible

drowning.

Pregnant or possibly pregnant women should consult a physician before using a spa or tub.

Water temperature in excess of 100°F (38°C) may be hazardous to your health.

Before entering a spa or hot tub, measure the water temperature with an accurate thermometer.

Do not use a spa or hot tub immediately following strenuous exercise.

Prolonged immersion in a spa or hot tub may be injurious to your health.

Do not permit any electric appliance (such as a light, telephone, radio, or television) within ve (5) feet (1.52 m)

of a spa or hot tub.

The use of alcohol, drugs or medication can greatly increase the risk of fatal hyperthermia in hot tubs and spas.

WARNING

A terminal bar marked “GROUND” is provided within the controller. To reduce the risk of electrical shock which

can cause serious injury or death, connect this terminal bar to the grounding terminal of your electric service

or supply panel with a continuous copper conductor having green insulation and one that is equivalent in size

to the circuit conductors supplying this equipment, but no smaller than no. 12 AWG (3.3 mm2). In addition, a

second wire connector should be bonded with a no. 8 AWG (8.4 mm2) copper wire to any metal ladders, water

pipes, or other metal within ve (5) feet (1.52 m) of the pool/spa. In Canada the bonding wire must be minimum

6 AWG (13.3 mm2).

CAUTION

The conductors on the load side of the ground-fault circuit-interrupter shall not occupy conduit, boxes, or

enclosures containing other conductors unless the additional conductors are also protected by a ground-fault

circuit-interrupter. Refer to local codes for complete details. MAINTAIN WATER CHEMISTRY IN ACCORDANCE

WITH MANUFACTURER'S INSTRUCTIONS.

WARNING

To reduce the risk of electric shock, re or injury, service should only be attempted by a qualied pool service

professional.

Risk of Electric Shock. Connect only to a branch circuit protected by a ground-fault circuit-interrupter (GFCI).

(in Canada: CONNECT ONLY TO A CIRCUIT PROTECTED BY A CLASS A GROUND FAULT CIRCUIT

INTERRUPTER) Contact a qualied electrician if you cannot verify that the circuit is protected by a GFCI.

Such a GFCI should be tested on a routine basis. (In Canada: TEST THE GROUND FAULT CIRCUIT

INTERRUPTER BEFORE EACH USE OF THE SPA) To test the GFCI, push the test button. The GFCI should

interrupt power. Push the reset button. Power should be restored. If the GFCI fails to operate in this manner, the

GFCI is defective. If the GFCI interrupts power to this equipment without the test button being pushed, a ground

current is owing, indicating the possibility of an electric shock. Do not use this equipment. Disconnect this

equipment and have the problem corrected by a qualied service representative before using.

Do not bury the cords. Locate cords to minimize abuse from lawn mowers, hedge trimmers, and other equipment.

To reduce the risk of electric shock, replace damaged cord immediately and do not use an extension cord to connect

unit to electric supply; provide a properly located outlet.

This equipment is for use with permanently-installed pools only. Do not use with storable pools. A storable pool is

constructed so that it is capable of being readily disassembled for storage and reassembled to its original integrity.

A permanently-installed pool is constructed in or on the ground or in a building such that it cannot be readily

disassembled for storage.

To reduce the risk of injury, do not permit children to use this product unless they are supervised at all times.

ENGLISH

Polaris® PAC™Pool Automation Control |Owner’s Manual Page 5

Section 2. System Overview

2.1 Package Contents

• Four Function Controller

• Water Temperature Sensor Kit

• Air Temperature Sensor

• Mounting Hardware

• Mounting Bracket

• Installation Manual/ Owner’s Manual

2.2 Electrical Specications

Power Supply 120 VAC; 60 Hz; 1.67 A

Contact Rating High voltage - 15 A;

1.5HP @ 120 VAC

1500 Watts Incandescent

Low Voltage - Class 2,

1 A @ 24 VAC

2.3 Materials and Tools

Installation Materials Furnished

• Screw Set (includes Plastic Anchors)

• Metal Mounting Bracket

Tools Needed for Installation

• Power Drill

• 3/16" Drill Bit - Hammer Drill Bit

(only necessary to drill into brick or concrete)

• Pencil or Marking Pen

• Flat Head Screwdriver

• Phillips Head Screwdriver

• Small Flathead or Slotted Screwdriver

• Protective Safety Eyewear

• Protective Work Gloves

Section 3. Install Controller Box

WARNING

FOR YOUR SAFETY: This product must be serviced

by a professional pool/spa service technician as

described on the front cover of this manual. The

procedures in this manual must be followed exactly.

Failure to follow warning notices and instructions may

result in property damage, serious injury, or death.

Improper installation and/or operation may void the

warranty.

Risk of Electric Shock. Connect only to a branch

circuit protected by a ground-fault circuit-interrupter

(GFCI). Contact a qualied electrician if you cannot

verify that the circuit is protected by a GFCI. To

reduce the risk of electric shock, do not use extension

cord to connect unit to electric supply; provide a

properly located outlet.

CAUTION

To reduce the risk of electric shock do not place the power

pack closer than 5 feet (1.5 m) from the pool. In Canada,

at least 3 meters (10 feet) horizontally from the edge of

the pool.

Do not bury the cords. Locate cords to minimize abuse

from lawn mowers, hedge trimmers, and other equipment.

When mounting the controller box in the equipment pad,

instructions must be followed exactly. Read through

the Important Safety Information section completely

before beginning installation and before operating the

equipment.

Before you begin installation, make sure you have the

necessary tools and a suitable location to install the

automation system.

NOTE: The controller should be located at or near the

equipment pad.

Locate the controller at least ve (5) feet or more away

from pool and two (2) feet (0.6m) o󰀨 the ground. In

Canada, at least 3 meters (10 feet) horizontally from the

edge of the pool. All national, state, and local codes are

applicable.

3.1 Mount the Controller Enclosure

1. Using a at screwdriver, rotate door tumblers

counter-clockwise to unlock the front cover of the

controller.

2. Open the front cover door and remove the

mounting hardware kit.

3. Using the holes in the bracket as a guide, mark

four (4) dots on the surface where the controller

will be mounted. The four (4) mounting holes are

3-15/16” (10 cm) apart center to center.

NOTE: Make sure to mark out the four (4) holes as

accurately as possible.

4. Drill four (4) holes in the mounting surface.

5. Press the four (4) plastic anchors rmly into holes.

ENGLISH Polaris® PAC™Pool Automation Control |Owner’s Manual

Page 6

6. Screw the mounting bracket onto the mounting

surface with the four (4) screws provided.

CAUTION

FOR YOUR SAFETY: Make sure to perform the

following step BEFORE mounting the enclosure

onto the mounting bracket, otherwise, damage to

the threaded hole of the mounting bracket may

occur.

7. Open the front cover of the controller and locate

the fastening hole under the ground bar. Drill a

3/16" hole through the plastic enclosure.

8. Line up the slot in the controller enclosure with

the guide in the mounting bracket and hook on to

mount.

9. Secure the controller enclosure to the mounting

bracket with the single ne thread Phillips screw

provided.

10. Plug into the GFCI outlet.

Mounting

Bracket

Anchors (4)

Screw

Screws (4)

Controller

Drill a 3/16” hole before

mounting onto the bracket

3.2 Bonding the Power Center

In addition to being properly grounded per this

installation manual, and in accordance with the

requirements of the National Electrical Code (NEC),

or in Canada the Canadian Electrical Code (CEC),

the power center must be bonded to all metal parts

of the swimming pool or hot tub structure and to all

electrical components and equipment associated with

the pool water circulation system. The bonding must be

accomplished by using a solid copper conductor, No. 8

AWG or larger. In Canada No. 6 AWG or larger must be

used. Bond the power center using the external bonding

lug provided on the outer frame.

National Electrical Code® (NEC®) requires bonding

of the Pool Water. Where none of the bonded pool

equipment, structures, or parts are in direct connection

with the pool water; the pool water shall be in direct

contact with an approved corrosion-resistant conductive

surface that exposes not less than 5800 mm² (9 in²)

of the surface area to the pool water at all times.

The conductive surface shall be located where it is

not exposed to physical damage or dislodgement

during usual pool activities, and it shall be bonded in

accordance with the bonding requirements of NEC

Article 680. Refer to locally enforced codes for any

additional bonding requirements.

Section 4. High Voltage Plug In

4.1 Plug In Assignment

The following call-outs display the plug in assignments

of the pool equipment.

Low Voltage Wiring

A - Filtration Pump: (120 VAC, 60Hz, 10A Max)

B (Aux 2) - Saltwater Chlorinator / Water Sanitizer:

(120 VAC, 60Hz, 3A Max)

C (Aux 2) & D (Aux 3) - Low Voltage Light Transformer:

(120 VAC, 60Hz, 1A Max)

Section 5. Low Voltage Wiring

All low voltage wiring should be run through the

knockouts in the low voltage compartment (right side of

controller enclosure).

IMPORTANT: Never run high voltage and low voltage

in the same conduit.

5.1 Wire the Temperature Sensors

Wire the temperature sensors on the 10-pin green

connector. The air temperature sensor is factory-installed

on the 10-pin green connector (pins 7,8). The water

temperature sensor and necessary installation hardware

is included.

5.2 Install the Water Temperature Sensor

1. Drill a hole (3/8") for mounting the water

temperature sensor line in the pipe between the

pump and the lter (before the heater).

2. Install the O-ring on the sensor and insert the

sensor into the hole. Wrap and tighten metal

clamp around the pipe to secure sensor.

3. Feed the sensor wire through the black low

voltage wiring knockout.

4. Strip 1/4″ of insulation and separate the wires.

5. Connect sensor wires to pins 5 and 6 of the 10-pin

green connector.

ENGLISH

Polaris® PAC™Pool Automation Control |Owner’s Manual Page 7

5.3 Install a Solar Sensor (if applicable)

If there is a solar panel in the equipment conguration,

wire the solar panel temperature sensor to the 10-pin

green connector. The solar sensor should be installed

adjacent to the solar panel so it will sense the same

temperature as the solar panels. Do not install in the

pipe.

1. Feed the sensor wire through the black low

voltage wiring knockout.

2. Strip 1/4″ of insulation and separate the wires.

3. Connect sensor wires to pins 3 and 4.

5.4 Install Additional Low Voltage

Equipment (i.e., Heater Connection)

If there is additional low voltage equipment installed,

such as low voltage heating, wire to pins 1 and 2 on the

10-pin green connector.

5.5 Install iAquaLink™(if applicable)

NOTE: For complete intructions and safety information,

refer to the iAquaLink Quick Start Guide

(included in the iAquaLink packaging), or the

full iAquaLink manual (found online at

www.PolarisPool.com).

5.6 Mount the iAquaLink Device

Mount the iAquaLink at least 6 feet o󰀨 the ground and at

least 8 feet from motors, such as a blower.

5.7 Wire the iAquaLink Device

Wire the iAquaLink device on the red RS-485 connector.

1. Feed wire through the black low voltage wiring

knockout.

2. Connect four (4) separate wires to each terminal.

3 Yellow

1 Red

2 Black

4 Green

Red 4-Pin Terminal Bar

NOTE: Wire only two (2) devices (e.g, the iAquaLink™

and one additional device) to the RS-485

connector. If you have more than one additional

device in your equipment conguration, use a

multiplex board.

5.8 Install Jandy Valve®Actuators (JVAs)

(if applicable)

You may wire up to a JVA on the PAC to control a water

feature or solar panel, for example.

You may wire up to a JVA on the PAC to control a water

feature or solar panel, for example.

NOTE: Read and follow complete installation

instructions and safety information in the Jandy

Valve Actuator owner’s manual (included in the

JVA packaging).

1. Install JVA on equipment lines according to

installation instructions in the owner’s manual.

2. Feed intake JVA wire through the black low

voltage wiring knockout.

3. Plug JVAs to Solar socket.

4. If the solar sensor is installed the solar JVA will

automatically assign to Solar Heat. If solar sensor

is not installed the solar JVA may be assigned to

one of the three (3) assemblies.

Section 6. User Interface

All system programming and installation setup is

performed through the automation system user interface

UI.

Power Button

Back Button

Up/Down (Scroll)

Arrows

Menu Screen

Select Button

6.1 Navigation Buttons

Use the following buttons on the user interface to

access and select all menus and commands:

On/O󰀨

Turn user interface power on/o󰀨.

Up/Down

Scroll up/down within current menu to

highlight a specic menu command.

Back

Go back to previous menu. To return to Main

menu, press Back button repeatedly.

Select

Select current highlighted menu command.

Display the next menu or activate the

selected function.

ENGLISH Polaris® PAC™Pool Automation Control |Owner’s Manual

Page 8

Section 7. Install Settings

Install Settings is a hidden menu, mostly used for setup

and reference purposes.

Settings available through this menu:

• Freeze Protect

Automatically turn specic equipment on to protect

against freezing temperatures.

• Units

Change units of measurement displayed on the

User Interface (temperature and time format).

• Language

Change language displayed on the User Interface.

• Clear Memory

Clear all programmed data in the controller for all

equipment.

• Color Lights

Only available if specic lights are installed in your

conguration.

• Label Aux

Assign custom labels to auxiliary equipment, such

as an air blower, cleaner, solar pump, etc.

• Temp Calibrate

Adjust temperature displayed on the User Interface

up or down by four (4) degrees.

• Solar Priority

Only available if solar heating is installed in your

system.

• Assign JVA

Assign Jandy Valve® Actuators (JVAs) to specic

AUX relays, as intake or return in Pool Only mode.

• Diagnostics

Display software revision information and alerts for

troubleshooting purposes.

To access the Install Settings Menu:

• Press and hold Up/Down arrow keys at the same

time for about 5 seconds.

Zodiac

12:40PM

Pool Mode On

Pool Heater 80°F

Aux1 Oﬀ

Aux2 Oﬀ

Settings >

Devices >

INSTALL SETTINGS

Freeze Protect >

Units >

Language >

Clear Memory >

Pump >

INSTALL SETTINGS

Color Light >

Label Aux >

Temp Calibrate >

Solar Priority >

Assign JVA >

Assign Hotkeys >

INSTALL SETTINGS

Diagnostics >

7.1 Freeze Protect

NOTE By factory default the lter pump circuit is freeze

protected. During freeze protection, the lter

pump cannot be turned o󰀨.

IMPORTANT

Freeze protection is intended to protect equipment

and plumbing for short periods of freezing only.

It does this by activating the filtration pump and

circulating the water to prevent freeze inside

equipment or plumbing. Freeze protection does

not guarantee that equipment will not be damaged

by extended periods of freezing temperatures or

power outages. In these conditions, the pool and

spa should be shut down completely (e.g. drained of

water and closed for the winter) until warmer weather

exists.

CAUTION

Activating the spa during freezing conditions will

override freeze protection. This means that if you are

using your spa when freezing conditions exist, freeze

protection will not circulate water to non-spa related

equipment that you may have freeze protected

(e.g. pool cleaner, booster pump.) Under these

circumstances, the potential for equipment damage

may exist.

ENGLISH

Polaris® PAC™Pool Automation Control |Owner’s Manual Page 9

Set Temperature:

INSTALL SETTINGS > FREEZE PROTECT >

SET TEMP

Set outside temperature at which freeze protect function

is activated. Activation temperature can be adjusted

between 34°F and 42°F. Default freeze protection

activation temperature is 38ºF. The freeze protected

equipment will turn o󰀨 when the temperature increases

2° F above the activation temperature.

INSTALL SETTINGS

Freeze Protect >

Units >

Language >

Clear Memory >

FREEZE PROTECT

Set Temp >

Equipment >

FREEZE PROTECT

TEMPERATURE

Temp: 38˚F

Select Equipment:

INSTALL SETTINGS > FREEZE PROTECT >

EQUIPMENT

Assign freeze protection to a selected piece of

equipment.

FREEZE PROTECT

Set Temp >

Equipment >



FREEZE PROTECT

EQUIPMENT

Filter Pump

Aux1

Aux2

Aux3



7.2 Units

INSTALL SETTINGS>UNITS

Change the temperature units (Fahrenheit - Celcius) and

time format (12-hour AM/PM to 24-hour clock).

INSTALL SETTINGS

Freeze Protect >

Units >

Language >

Clear Memory >

SET UNITS

˚F/˚C

AM/PM 24H

7.3 Languages

MAIN/STATUS>MENU>SYSTEM SETUP>LANGUAGE

Change the language displayed on the user interface.

Languages available are:

• English • Francais

• Espanol • Italiano

• Deutsch • Portuguese

• Nederlands • Afrikaans

English

Francias

Espanol

Italiano

Deutsch



INSTALL SETTINGS

Freeze Protect >

Units >

Language >

Clear Memory >

7.4 Clear Memory

INSTALL SETTINGS>CLEAR MEMORY

Clear all stored values (e.g., auxiliary labels, programs,

remote settings, and thermostat settings) from the

Polaris PAC memory. All settings will be reset to default

factory settings. Time and date is not cleared.

INSTALL SETTINGS

Freeze Protect >

Units >

Language >

Clear Memory >

Clear?

Yes

CLEAR MEMORY

Clear?

Are you sure you

want to clear?

Cancel

Yes

• The system asks you to verify you are sure you

want to clear memory.

• There is a 15-second delay and *MEMORY

CLEARED* message is displayed.

7.5 Color Lights

INSTALL SETTINGS > COLOR LIGHTS

NOTE You will only see this option if colored lights are

installed in your system.

ENGLISH Polaris® PAC™Pool Automation Control |Owner’s Manual

Page 10

Select type of light installed (e.g., Jandy ColorsTM or

Jandy® LED Light ) and assign the light to an available

auxiliary relay.

Select Light Type:

SELECT LIGHT

Jandy Color

Jandy LED

Intellibrit

Color Logic

INSTALL SETTINGS

Color Lights >

Label Aux >

Temp Calibrate >

Solar Priority >

Assign JVA >

Assign Selected Light to an Auxiliary:

SELECT LIGHT

Jandy Color

Jandy LED

ASSIGN TO AUX

Jandy Color

Aux1 JC

Aux2

Aux3

• JC is displayed next to AUX if a Jandy Colors light

has been assigned.

• JL is displayed next to AUX if a Jandy LED Light

has been assigned.

• Press Select button with JC or JL highlighted to

toggle control by the auxiliary on or o󰀨.

7.6 Label Auxiliary Functions

INSTALL SETTINGS>LABEL AUX

Assign labels to auxiliary equipment to display text in the

user interface instead of AUX 1, 2, or 3.

INSTALL SETTINGS

Color Lights >

Label Aux >

Temp Calibrate >

Solar Priority >

Assign JVA >

LABEL AUX

Aux1 >

Aux2 >

Aux3 >

Label = Aux2

Swim Jet

Valve(s)

Wtr Feature

Waterfalls

Whirlpool

Label = Aux2

Aerator

Air Blower

Backwash

Chlorinator

A-Z

• Choose from labels listed A-Z on each screen.

7.7 Temp Calibrate

INSTALL SETTINGS>TEMP CALIBRATE

Adjust temperature displayed on the Polaris PAC up or

down by 4 degrees.

NOTE If the temperature is o󰀨 by more than four

(4) degrees, contact your local service

representative.

SYSTEM SETUP

Label Aux >

Temp Calibrate >

Solar Priority >

Assign JVA >

Color Light >

TEMPERATURE

CALIBRATE

Water: 74°F

• Use Up/Down arrows to set new temperature

value.

7.8 Solar Priority (if applicable)

INSTALL SETTINGS>SOLAR PRIORITY

NOTE: You will only see this option if solar heating

is installed in your system.

Enable the system to use solar heat rst, when

available. If solar heat is no longer available, the system

will automatically switch to the alternate heat source.

SOLAR PRIORITY

Enable

Disable



INSTALL SETTINGS

Color Lights >

Label Aux >

Temp Calibrate >

Solar Priority >

Assign JVA >

• When solar and heater are enabled the solar will

heat the water until either the thermostat setting

has been reached or solar heat is no longer

available.

• If the solar panel is not hot enough, solar heat will

shut o󰀨 and the other heat source (usually gas

heater) will take over to bring the water up to the

thermostat setting.

7.9 Assign JVA

INSTALL SETTINGS>ASSIGN JVA

NOTE: If the system is a pool/spa combination, without

solar, only the solar JVA is assignable. If the

system is a pool or spa only system, without

solar, all three JVAs are assignable. The

example shown is for a pool or spa only system

without solar.

Indice

Lingue:

Altri manuali Polaris Unità di controllo

Polaris

Polaris Sync 3 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente