Polycom RealPresence Group Series Istruzioni utente
www.polycom.com
© 2014, Polycom, Inc. All rights reserved. POLYCOM® and the names and marks associated with Polycom’s products are trademarks and/or service marks of
Polycom, Inc. and are registered and/or common law marks in the United States and various other countries. No portion hereof may be reproduced
or transmitted in any form or by any means, for any purpose other than the recipient’s personal use, without the express written permission of Polycom.
1725-68117-001/A
Setting Up the Polycom®RealPresence®
Group Series Media Center with 65” Dual Displays
The Media Center components are heavy. Polycom recommends that two people perform the installation.
For more information about the components of the RealPresence Group Series Media Center,
refer to the documentation at
http://support.polycom.com/PolycomService/support/us/support/video/group_series/group_packaged_solutions.html.
1
Single 55/65” Lower Display Rail, 1354-67626-001
(2) Dual 65” Lower Display Rail Extension, 1354-68667-001
Dual 65” Center Top Display Rail, 1354-68669-001
(2) Dual 65” Upper Display Rail Extension, 1354-68671-001
This supplement describes how to attach 65” dual displays on the Polycom®RealPresence®Group Series
Media Center. Follow the instructions in Setting Up the Polycom RealPresence Group Series Media Center,
1725-08510-00X, and use this supplement to replace the steps to install the displays.
(4) Display Mounting Bracket
Assembly
2342-67629-001
(4) M8 x 20 Button Head Cap Screw
1601-52713-001
(4) M8 Hex Flange Nut
1600-52845-001
(4) M10 x 25 Flanged Socket Head
Cap Screw
1601-67617-001
M8 Wrench
1102-68064-001
6a
5b
Setting up the Polycom® RealPresence® Group Series Media Center 2
5a
Attach an upper display rail extension to each end of the center top display rail using two M10 x 25 flanged
socket head cap screws per extension.
Install the lower display rail by aligning the holes in
the display rail with the holes in the vertical
supports. Attach with four M10 x 25 flanged socket
head cap screws. Do not fully tighten.
Install a lower display rail extension to each side of
the lower display rail using two M8 x 20 button
head cap screws and two M8 hex nuts per side.
Ensure the edge of the rail extension is flush with
the edge of the lower display rail.Tighten using the
supplied M8 wrench.
6b Install the upper display rail assembly by aligning the holes in the display rail with the holes in the vertical
supports. Attach with two M10 x 25 flanged socket head cap screws per vertical support. Do not fully tighten.
Setting up the Polycom® RealPresence® Group Series Media Center 3
8Attach the rear panel by inserting the two tabs at the
bottom of the door into the slots in the base. This
serves as an alignment tool to ensure the frame is
properly aligned before tightening all bolts. Using
the L-key, tighten the socket head cap screws at
the bottom of the base, the lower display rail, and
the upper display rail. Remove the rear door.
13 On the back side, install a handle on both ends
of the bottom display rail.
15
14 Install the display mount brackets on the display. Position the third hole down from the top of the display
bracket with the third hole down from the top of the display. The bottom hole on the display will line up with the
fifth hole up from the bottom of the display bracket.
Install the supplied 1/4-20 x 3.5” socket head cap screws at the top of each display bracket. Leave the screws
adjusted up before mounting the display to the top rail.
Repeat with the second display.
With the assistance of another person, lift the display and position the display bracket hooks above the edge
of the upper horizontal display rail on the Media Center. Carefully lower the display onto the rail, ensuring the
hooks are fully engaged with the rail and that the outer most bracket is positioned within the safety tab on the
outer rail end (1). Repeat with the second display.
Adjust the leveler screws as needed to help eliminate any gap between the two displays when they are tightly
abutted (2).
TOP
BOTTOM
Setting up the Polycom® RealPresence® Group Series Media Center 4
1
2
16 Center the displays on the Media Center. Insert one M6 x 16 flanged button head screw into each
display bracket to lock the displays.
Setting up the Polycom® RealPresence® Group Series Media Center 5
Regulatory Notices:
This equipment is intended for indoor use only.
Only use this equipment with the displays supplied by
Polycom.
Do not use a power cord that is damaged. This could cause
fire or electric shock. Contact the manufacturer for a
replacement cord, if necessary.
Only use a power cord which is appropriately rated and
approved relevant to the country of use.
This equipment should be used only on even surfaces.
When moving or positioning the system, only use the
handles located at the bottom of the display rail at the rear
of the unit.
This equipment has lockable wheels which should be
applied while the cart is stationary.
When connecting to the mains supply, connect only to an
earthed supply outlet which is installed near the equipment
and is easily accessible.
Keep ventilation openings free from any obstructions.
The ambient operating temperature rating of this equipment
is 0 - 40ºC and should not be exceeded.
Do not immerse the system in any liquid or place any liquids
on it.
Do not spray liquids directly onto the system when cleaning.
Always apply the liquid first to a static-free cloth.
For further information concerning the individual components
of this equipment, please refer to the respective product
literature.
For support or service, please contact your Polycom®
distributor or go to Polycom Support at
www.polycom.com/support.
Power Rating:
Voltage rating: 100-240 VAC, 50/60Hz
Maximum power consumption (configured with Group
Series 500 codec and EagleEye IV camera under full
load operating conditions): 231.4W
Approximate system weight (including display(s),
codec, camera, and sound system): 715 lbs.
Altri manuali per RealPresence Group Series
24
Indice
Altri manuali Polycom Sistema di conferenza
Polycom
Polycom RealPresence Trio 8500 Manuale utente
Polycom
Polycom SoundPoint IP 501 SIP 2.2 Manuale utente
Polycom
Polycom ViewStation FX Manuale utente
Polycom
Polycom SoundStation 2W Manuale di servizio
Polycom
Polycom CX5500 Manuale utente
Polycom
Polycom HDX 4500 Documento tecnico
Polycom
Polycom RMX 1000 Manuale utente
Polycom
Polycom IPOWER 9000 Manuale utente
Polycom
Polycom DMA 7000 Manuale utente
Polycom
Polycom VIEWSTATION EX Manuale di istruzioni
Polycom
Polycom RealPresence Group Series Come usare
Polycom
Polycom NOT FOUND VTX 1000 Come usare
Polycom
Polycom V700 Manuale utente
Polycom
Polycom realpresence trio 8800 Manuale utente
Polycom
Polycom IPOWER 9000 Manuale utente
Polycom
Polycom RMX 2000 Manuale utente
Polycom
Polycom 3000 Manuale utente
Polycom
Polycom RealPresence Group Series Istruzioni per il montaggio
Polycom
Polycom MOBILE RESPONDER 3725-23487-003/A Manuale utente
Polycom
Polycom RealPresence RMX 4000 Scheda tecnica
Manuali Sistema di conferenza popolari di altre marche
Kramer
Kramer VIA GO Manuale utente
AVT
AVT MAGIC AC1 Go Manuale utente
ProSoft Technology
ProSoft Technology AN-X4-AB-DHRIO Manuale utente
Sony
Sony PCS-I150 Manuale utente
Middle Atlantic Products
Middle Atlantic Products VTC Series Manuale utente
Prentke Romich Company
Prentke Romich Company Vanguard Plus Guida
