PowerWalker VFI 6000RT LCD Manuale utente

USER MANUAL

On-Line UPS

PowerWalker VFI 6000RT LCD

PowerWalker VFI 6000P/RT LCD

PowerWalker VFI 10000RT LCD

PowerWalker VFI 10000P/RT LCD

Uninterruptible Power Supply System

Contents

1. Introduction......................................................................................... 1

2. Safety Warnings.................................................................................. 4

2.1 Installation ...................................................................................... 4

2.2 Operation........................................................................................ 5

2.3 Maintenance, servicing and faults ................................................... 6

2.4 Transport ........................................................................................ 7

2.5 Storage........................................................................................... 7

2.6 Standards ....................................................................................... 7

3. Installation........................................................................................... 9

3.1 Inspecting the Equipment................................................................ 9

3.2 Unpacking the carton ...................................................................... 9

3.3 UPS Rear Panel ........................................................................... 12

3.4 UPS Front Panel........................................................................... 13

3.5 Rack mount Setup ........................................................................ 14

3.6 Tower Setup.................................................................................. 18

3.7 Installation of UPS with AC inputs ................................................. 19

4. Power cables connection & Startup................................................. 21

4.1 Access to terminal block................................................................ 22

4.2 Common input sources connection ............................................... 22

4.3 Separate input sources connection ............................................... 23

4.4 Frequency converter connection ................................................... 24

4.5 UPS Initial Startup......................................................................... 24

4.6 Parallel Installation and Operation................................................. 25

5. Operation........................................................................................... 31

5.1 Display Panel................................................................................ 31

5.2 Operating mode............................................................................ 33

5.3 Turning on and Turning off UPS .................................................... 36

5.4 LCD operation .............................................................................. 38

6. UPS Maintenance.............................................................................. 47

6.1 UPS and Battery Care .................................................................. 47

6.2 Transporting the UPS.................................................................... 47

6.3 Storing the UPS and Batteries....................................................... 48

6.4 Testing Batteries ........................................................................... 48

6.5 Recycling the Used Battery or UPS............................................... 49

7. Specifications ................................................................................... 50

7.1 Electrical specification................................................................... 50

7.2 Dimension and Weight.................................................................. 51

7.3 Operating Environment ................................................................. 51

8. Troubleshooting................................................................................ 52

8.1 Typical Alarms and Conditions ...................................................... 52

9. Communication................................................................................. 57

9.1 RS-232 and USB Communication Ports ........................................ 57

9.2 Network Management Card (Optional) .......................................... 59

9.3 UPS Management Software.......................................................... 59

9.4 REPO Function............................................................................. 60

1. Introduction

This Online R/T Series is an uninterruptible power supply

incorporating double-conversion technology. It provides perfect

protection specifically for computer equipment, communication

systems to computerized instruments. It protects your sensitive

electronic equipment from basic power problems such as power

failures, power sags, power surges, brownout, and line noise.

Power outages can occur when you least expect them and power

quality can be erratic. These power problems have the potential to

corrupt critical data, destroy unsaved work sessions, and damage

hardware

－

causing hours of lost productivity and expensive

repairs.

With the Online R/T UPS, you can safely eliminate the effects of

power disturbances and guard the integrity of your equipment. The

UPS can handle array--network devices flexibility that makes it the

best choice for protect your LANs, servers, workstations, and other

electrical equipment.

Online R/T UPS as Rack installation:

Figure 1-1: Online R/T 6K UPS

Figure 1-2: Online R/T 10K UPS

Online R/T UPS as Tower installation.

Figure 1-3: Online R/T 6K UPS Figure 1-4: Online R/T 10K UPS

Providing outstanding performance and reliability, the UPS’s unique

benefits include:

Online UPS design with pure sine wave output.

True online double-conversion technology with high power

density, utility frequency independence, and generator

compatibility.

Intelligent Battery Management technology that uses advanced

battery management to increase battery service life, optimize

recharge time.

Selectable High Efficiency mode of operation.

Start-on-battery capability for powering up the UPS even if

utility power is not available.

Standard communication options: one RS-232 communication

port, one USB communication port.

Optional connectivity cards with enhanced communication

capabilities.

Extended runtime with up to four Extended Battery Modules

(EBMs) per UPS.

Optional installation method

－

Rack & Tower.

Remote shutdown control through the Remote Emergent

Power-off (REPO) port.

Maintenances are simplified by allowing the safe replacement

of batteries without powering down the UPS.

Parallel with another Online R/T UPS, max amount is 2.

Optional Rack Slider.

PDU is standard configuration with maintenance bypass

switch.

2. Safety Warnings

IMPORTANT SAFETY INSTRUCTIONS FOR EACH STEP SAVE

THESE INSTRRUCTIONS.

2.1 Installation

Condensation may occur if the UPS is moved directly from a

cold to a warm environment. The UPS must be absolutely dry

before being installed. Please allow an acclimatization time of

at least two hours.

Do not install the UPS near water or in damp environment.

Do not install the UPS where it would be exposed to direct

sunlight or near heat.

Do not block ventilation openings in the UPS’s housing.

Place cables in such a way that no one can step on or trip over

them.

UPS has provided earthed terminal, in the final installed system

configuration, equipotent earth bonding to the external UPS

battery cabinets.

An integral single emergency switching device which prevents

further supply to the load by the UPS in any operation mode

should be provided in the building wiring installation.

An appropriate disconnect device as short-circuit backup

protection should be provided in the building wiring installation.

For three-phase equipment connection to an IT power system,

a four-pole device which disconnect all phase conductors and

CAUTION:

Before performing the procedures in this document, read and follow

the safety instructions and important regulatory information in your

Safety, Environmental, and Regulatory Information document.

the neutral conductor should be provided in the building wiring

installation.

This is permanently connected equipment , it must be installed

by qualified maintenance personnel.

For permanently connected equipment: make sure that a

readily accessible disconnect device is incorporated in the

building installation wiring.

To reduce the risk of fire, connect only to a circuit provided with

branch circuit overcurrent protection with an ampere rating in

accordance with the IEC/EN 60934 standard or your local

electrical code and have a contact air gap of at least 3 mm.

Uninterruptible power supply

output power 240V

6K 40 amp

2-pole circuit breaker

10K 63 amp

2-pole circuit breaker

You can connect four extended battery modules to the

uninterruptible power supply.

Earthing connection is essential before connecting to the

building wiring terminal.

2.2 Operation

Do not disconnect the earth conductor cable from the UPS or

the building wiring terminals in any time since this would cancel

the protective earthing of the UPS system and all connected

loads.

The UPS output terminal block may be electrically active even if

the UPS system is not connected to the building wiring

terminal.

In order to completely disconnect the UPS, firstly press the

OFF button, and then disconnect the mains lead.

Ensure that no liquid or other foreign objects can enter the

UPS.

The UPS can be operated by any individual without previous

experience.

2.3 Maintenance, servicing and faults

The UPS operates with hazardous voltages. Maintenance

should be carried out only by qualified maintenance personnel.

Caution - risk of electric shock. Even after the unit is

disconnected from the mains power supply (building wiring

terminal), components inside the UPS are still connected to the

battery which have potentially dangerous.

Before carrying out any kind of service and/or maintenance,

please disconnect the batteries. Verify that no current is

present and no hazardous voltage exist in the capacitor or BUS

capacitor terminals.

Batteries must be replaced only by qualified personnel.

Caution – the risk of electric shock. The battery circuit is not

isolated from the input voltage. Hazardous voltage may occur

between the battery terminals and the ground. Verify that no

voltage is present before servicing!

Batteries have a high short-circuit current and pose a risk of

shock. Take all precautionary measures specified as below and

any other measures necessary when working with batteries:

1) Remove all jewellery, wristwatches, rings and other metal

objects

2) Use only tools with insulated grips and handles.

3) When changing batteries, replace with the same quantity

and the same type of batteries.

4) Do not attempt to dispose of batteries by burning them. It

could cause explosion.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali PowerWalker UPS

PowerWalker

PowerWalker VFI ICT IoT Series Manuale utente

PowerWalker

PowerWalker VI 1200 RLE Manuale utente

PowerWalker

PowerWalker VFI 1000 Manuale utente

PowerWalker

PowerWalker VFI 6000T LCD L Manuale utente

PowerWalker

PowerWalker Basic VI 3000 STL Manuale utente

PowerWalker

PowerWalker VFD 400 IEC Manuale utente

PowerWalker

PowerWalker VI 3000RT LCD Manuale utente

PowerWalker

PowerWalker VFI 2000 RMG/S PF1 Manuale utente

PowerWalker

PowerWalker VI 450 LCD Manuale utente

PowerWalker

PowerWalker VI 750 PSW Manuale utente

PowerWalker

PowerWalker VFI 1000-3000 CG PF1 Manuale utente

PowerWalker

PowerWalker VFI 10000 CPE 3/3 Manuale utente

PowerWalker

PowerWalker VFI 10K-80K CPG 3 Manuale utente

PowerWalker

PowerWalker VI 650 GX Manuale utente

PowerWalker

PowerWalker MBP 1-1 Manuale utente

PowerWalker

PowerWalker VFD 400 Manuale utente

PowerWalker

PowerWalker VFI CPG PF1 3/3 Series Manuale utente

PowerWalker

PowerWalker VFD 400 Manuale utente

PowerWalker

PowerWalker VI SCL Series Manuale utente

PowerWalker

PowerWalker VFI 1000 RMG PF1 Manuale utente

PowerWalker

PowerWalker VFI 1000RT LCD Manuale utente

PowerWalker

PowerWalker VI 1000RT LCD Manuale utente

PowerWalker

PowerWalker VFI 1000CRM LCD Manuale utente

PowerWalker

PowerWalker VFI 6000 LCD Manuale utente

Manuali UPS popolari di altre marche

Pylontech

Pylontech Victron & Pylontech US5000 Manuale utente

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuale utente

Mecer

Mecer ME-1000-WTU Manuale utente

Mustek

Mustek PowerMust 530(B) Plus Manuale di installazione e funzionamento

Emerson

Emerson Liebert NXL series Manuale utente

MAKELSAN

MAKELSAN BOXER SERIES Manuale utente

Block

Block PC-0524-400-0 Manuale utente

CyberPower

CyberPower CP585LCD Manuale utente

Eaton

Eaton 3S Istruzioni per il montaggio

CyberPower

CyberPower Office Tower Series UPS 1000 Manuale utente

CyberPower

CyberPower BM100 Manuale utente

Best Power

Best Power 610 Manuale utente

Best Power

Best Power Unity/I UT3K Manuale utente

Mustek

Mustek PowerMust 400 Offline Manuale utente

Xantrex

Xantrex Trace 512 UR-UPS Manuale utente

Forza

Forza SL-1501UL Manuale utente

LEGRAND

LEGRAND keor 310081 Manuale utente

ABB

ABB Conceptpower DPA 500 Manuale utente