PowerWalker VFI 1000T/E LCD Manuale utente

USER MANUAL

ONLINE UPS

PowerWalker VFI 1000T/E LCD

PowerWalker VFI 2000T/E LCD

PowerWalker VFI 3000T/E LCD

Contents

1. Product introduction......................................................................... 2

1.1 Function description......................................................................1

1.2 Front panel....................................................................................2

1.3 Rear panel.....................................................................................5

1.4 Mode description...........................................................................7

1.5 Product specification...................................................................10

1.6 Communication port....................................................................12

2. Installation........................................................................................14

2.1 Safety Instructions for Installation...............................................14

2.2 Unpacking and Inspection...........................................................15

2.3 Installation steps for standard model..........................................16

2.4 Installation for communication software (optional) ..................... 16

3. Operation .........................................................................................18

3.1 Operation Safety Instructions......................................................18

3.2 Start the UPS with mains (AC source)........................................19

3.3 Start the UPS with battery (DC source) only ..............................20

3.4 Connect loads to UPS.................................................................21

3.5 Charge the batteries ...................................................................21

3.6 Discharge the batteries...............................................................22

3.7 Test the batteries.........................................................................22

3.8 Turn off the UPS with mains (AC source)...................................23

3.9 Turn off the UPS with battery (DC) only......................................23

4. Maintenance..................................................................................... 24

4.1 Maintenance Safety Instructions................................................. 24

4.2 Typical Troubleshooting ..............................................................26

4.3 Battery Maintenance...................................................................28

4.4 Contact the service centre..........................................................28

5. Transport and Storage....................................................................29

6. Standards.........................................................................................30

1. Product introduction

1.1 Function description

This product is a true online double-conversion UPS

(Uninterruptible Power Supply). It provides perfect protection for

critical load such as computer system. It can eliminate almost all

mains power disturbances. The input AC current can be

corrected to a wave following the mains voltage, so it is a high

power factor system. Through the PWM control technology, the

output voltage can be a pure & stable sine waveAC voltage.

When the mains input become abnormal, the controller will stop

the AC/DC and start the DC/DC section immediately to make

sure the DC/AC (inverter) section can continue to work. After the

mains input come back to normal range, the DC/DC will be

stopped and the AC/DC works again. So the load is always

power-supplied through inverter without any interrupt if the UPS

is turned on.

The UPS also provides an internal bypass path so that the load

can be powered by mains input directly when the UPS is off or

failed.

The UPS is equipped with an internal charger for batteries which

charges the batteries when the mains are within a reasonable

range under “bypass mode” or “line mode”.

1.2 Front panel

1.2.1 Front view

1K 2K/3K

1.2.2 LCD and LED display

LED definition

There are total 4 LEDs to indicate the status of UPS.

Name

Colour

Function

Bypass LED

Orange

To indicate that the UPS is in bypass

mode, and the load current is directly from

the mains power.

Line LED

Green

To indicate that the mains input is normal.

Inverter LED

Green

To indicate that the load current is

supplied from the mains power or battery

via the inverter.

Battery LED

Orange

To indicate that the UPS is in battery

mode, and the load current is from battery

via the inverter.

1.2.3 Button

(1) ON/OFF button

Turn on UPS

Press ON/OFF button for 1 second to turn on UPS.

UPS would send a beep to indicate the power-on

status

Turn off UPS

Press ON/OFF button for 1 second to turn off UPS

when UPS is in line mode or battery mode.

Clear fault status

Press ON/OFF button for 3 seconds to clear the fault

status of UPS.

(2) Test button

Battery test

In line mode, press test button for 2 seconds to test

the battery.

Mute in battery mode

Press test button for 2 seconds in battery mode,

UPS would be muted. To resume the alarm, press

test button again for 2 seconds.

Mute in all mode

Press test button for 10 seconds, UPS would be

muted. To resume the alarm, press test button again

for 10 seconds. The key tone and battery voltage

under alarm (every second buzzer beep twice)

cannot be muted.

Page up/down

Press test button for 0.5 seconds, UPS would turn

from main menu to sub-menu in sequence

1.3 Rear panel

1K-IEC

1K-SCHUKO

1K-UK

2K-IEC

Communication port (RS232)

Mains input protection

Intelligent card slot

Mains input power cord

Fan

Output terminal block

2K/3K-SCHUKO

2K/3K-UK

3K-IEC

Output socket

1.4 Mode description

Line mode

Line mode means that the mains input is rectified/converted by the

AC/DC section and then inverted to stable output by DC/AC section.

In line mode, the output is well-regulated and good to the loads. If

the mains get abnormal, the UPS will transfer to battery mode

without interruption.

In line mode, Line LED and Inverter LED are turned on constantly.

1. If Line LED flashes, it means that the input may have something

wrong, such as input L and N line reversed or the grounding wire

is not connected properly.

2. If the load level is higher than 100%, the buzzer will beep one

every 0.5 second as a warning for the over-loading condition.

The user should remove unnecessary loads one by one, until the

load level become lower than 100%.

Line mode

3. If the Battery LED flashes, it means that the battery is not

connected or the battery level is too low. In this case please

check the connection of battery and press test button for 2

seconds to test the battery. If the connection is normal, it’s

possible the battery is failed or aged. Please refer to the

common troubleshooting table in chapter 4.

Connecting AC Generator as Input

Remove the loads connected to UPS first. Activate the generator

and connect the output of generator with the input of UPS until the

generator operates stably, then turn on the UPS and add the loads

one by one.

Please choose the generator with output capacity which is twice

larger than the UPS capacity.

Battery mode

Battery mode means that the battery power goes through the DC/DC

section to the inverter (DC/AC) and output a stable backup power

when the mains are failed. If the mains recovered, the UPS will

transfer to line mode without interruption.

In battery mode, Battery LED and Inverter LED are turned on

constantly. If Line LED flashes at the same time, it means that the

input mains are abnormal.

Questo manuale è adatto per i seguenti modelli

Indice

Altri manuali PowerWalker UPS

PowerWalker

PowerWalker VFI 1000RM Manuale utente

PowerWalker

PowerWalker VFI 10000 CPE 3/3 Manuale utente

PowerWalker

PowerWalker VFI 2000RT Manuale utente

PowerWalker

PowerWalker VFI RT HID Series Manuale utente

PowerWalker

PowerWalker DC UPS Manuale utente

PowerWalker

PowerWalker VFI 6000 CT LCD Manuale utente

PowerWalker

PowerWalker VFI 10K CPH Manuale utente

PowerWalker

PowerWalker VFD 400 Manuale utente

PowerWalker

PowerWalker VFI 10000TCP 3/1 Manuale utente

PowerWalker

PowerWalker VI 750 PSW Manuale utente

PowerWalker

PowerWalker VFI 1000 AT Manuale utente

PowerWalker

PowerWalker VFI 1000R/1U Manuale utente

PowerWalker

PowerWalker VFI 3000 LCD Guida all'installazione

PowerWalker

PowerWalker VI 400 Manuale utente

PowerWalker

PowerWalker VFI 6000 CG PF1 Manuale di installazione e funzionamento

PowerWalker

PowerWalker VFI CPG PF1 3/3 Series Manuale utente

PowerWalker

PowerWalker 1000 LCD/UK Manuale utente

PowerWalker

PowerWalker VFI 6000 AT Manuale utente

PowerWalker

PowerWalker VFI 6000 TGB Manuale utente

PowerWalker

PowerWalker VFI 1000 CRM Manuale utente

PowerWalker

PowerWalker MBP 1-1 Manuale utente

PowerWalker

PowerWalker VFI 1000 RMG PF1 Manuale utente

PowerWalker

PowerWalker VFI 2000 RMG/S PF1 Manuale utente

PowerWalker

PowerWalker VFI 160K CPG 3/3 BX Manuale utente

Manuali UPS popolari di altre marche

Pylontech

Pylontech Victron & Pylontech US5000 Manuale utente

Tecnoware

Tecnoware EVO DSP PLUS MM 6.8 Manuale utente

Mecer

Mecer ME-1000-WTU Manuale utente

Mustek

Mustek PowerMust 530(B) Plus Manuale di installazione e funzionamento

Emerson

Emerson Liebert NXL series Manuale utente

MAKELSAN

MAKELSAN BOXER SERIES Manuale utente

Block

Block PC-0524-400-0 Manuale utente

CyberPower

CyberPower CP585LCD Manuale utente

Eaton

Eaton 3S Istruzioni per il montaggio

CyberPower

CyberPower Office Tower Series UPS 1000 Manuale utente

CyberPower

CyberPower BM100 Manuale utente

Best Power

Best Power 610 Manuale utente

Best Power

Best Power Unity/I UT3K Manuale utente

Mustek

Mustek PowerMust 400 Offline Manuale utente

Xantrex

Xantrex Trace 512 UR-UPS Manuale utente

Forza

Forza SL-1501UL Manuale utente

LEGRAND

LEGRAND keor 310081 Manuale utente

ABB

ABB Conceptpower DPA 500 Manuale utente