Premier Mounts AM100 Manuale utente

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

1321 S. State College Blvd., Fullerton, CA 92831 USA

Installation Guide

AM100

Low-Prole Ultra-Slim Swingout Mount for Flat-Panels

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

Included Components

Required for installation

AM100

Installation Guide

Maximum Flat Panel Weight:

100 lb. / 45.5 kg.

5/16” x 3” Lag Bolts

(Qty 4)

Green Level

(Qty 1)

Universal Spacers

(Qty 8)

5/16” Flat Washers

(Qty 4)

Universal Washers

(Qty 4)

Depth Measuring Straw

(Qty 1)

10mm Socket

(Qty 1)

M4 Allen Key

(Qty 1)

M2.5 Allen Key

(Qty 1)

Finned Anchor

(Qty 4)

Pencil Protective Eyewear

Electronic Stud Finder M6 or 1/4” Wood Drill Bit 3/8” Concrete Drill Bit

Portable Drill Hammer

Phillips Head ScrewdriverLeveler Socket Wrench

13mm or 1/2” Socket

M6 x 16mm (Qty 4)

M6 x 25mm (Qty 4)

M8 x 16mm (Qty 4)

M8 x 25mm (Qty 4)

Wall Mount

(Qty 1)

Template

(Qty 1)

Page 2

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

Installation Guide

AM100

Prior to initial step 1 of the installation, your AM100 can easily

have the main “swing left” pivot point of the main swing out

arm moved to either the center, left or right of the mount by

simply placing the mount on a flat surface and removing the

eight flat head screws, then separating the upper and lower

wall plates.

Pivot

Set Screw

Locations

Set Screw

Locations

Remove the plastic hole covers from the upper and lower

plates. Loosen the (2) set screws on the plate using the

2.5mm allen key supplied. Reposition the upper and lower

pivot rods to mate to either the center or right side pivot

receiver holes, push the upper and lower plate fully on to the

rods, and re-tighten the set screws. Reinstall the side plate

with the eight flat head screws and confirm they are secure.

Reinstall the round plastic hole covers.

M2.5 Allen Key

Page 3

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

Installation Guide

AM100

Using a suitable stud-finder device for frame walls, mark the

position of the stud centers.

Measure the desired height of the center of the screen and

mark it.

Take the thick cardboard mounting template supplied and

place the it over the mounting studs with the screen center

facing up. Confirm that the template is level horizontally and

that the wall place outline is to the center of your desired

height.

Page 4

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

Installation Guide

AM100

Using a 1/4” drill bit, drill pilot holes minimum 2” (50mm)

deep into the four marked mounting points on the wall

surface. For solid concrete wall construction, the supplied

plastic wedge anchors are recommend to be used with the

5/16 x 3” lag bolt and washers supplied.

To ease the installation process you have the option to

remove the wide front plate and mounting brackets by simply

removing the three M5 x 10mm flat head screws, holding

the plate assembly to the swing out arm assembly and set-

ting them aside.

1/4” / M6

Wood Only

Page 5

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

Installation Guide

AM100

Raise the AM100 assembly so the mounting slots are

over the four drilled mounting holes. Confirm mount

level with spirit level and secure the mount to the wall

surface with the four each 5/16 x 3” lag bolt and 5/16”

flat washer supplied.

Level the wall mount in the following order on figure 5

and below

Re-confirm secured assembly is level horizontally and

vertically or level again if necessary before proceeding.

NOTE: Do not over tighten lag bolts

1. Level the wall mount in following order on figure 6

and below.

2. Mark the pointing points.

3. Drill the concrete wall using a 3/8” concrete drill bit.

4. Lighty hammer the four (4) Finned Anchors into the wall.

5. Tighten the (4) 5/16” washers and (4) 5/16” x 3” lag bolts into

the wall.

Wood Stud

Concrete Wall

Leveler

1/2”

x4x4

Page 6

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

Installation Guide

AM100

7Re-install the front wall arm plate to the arm with the three

M5 flat head screws you set aside earlier. Confirm screws

are fully seated and tight.

Take the plastic depth straw supplied and confirm the overall

“safe” screw depth that can be used.

Page 7

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

Installation Guide

AM100

10A

Once the correct pitch and depth screws are pulled from

the hardware pack supplied, secure the two brackets to the

rear of the display with the proper screws and plate washer

holes. Plastic spacers are also supplied in case you need

additional clearance between the bracket and the rear of the

display. NOTE: Do not over tighten the screws.

9Place the display face down on a smooth flat surface. Place

the left and right mounting brackets over the four mounting

points on the rear of the display arrow pointing up to the top

of the display, making sure the brackets are lined up with the

center top to bottom on the display.

Page 8

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

Installation Guide

AM100

10B With the upper and lower security screws loosened on each

bracket (two people recommended) raise the display and

place the top hook of the bracket over the receiver plate on

the wall mount. Allow the lower end of the bracket to lay flat

against the mating plate on the mount.

Center the display horizontally on the plate and check the

display is level on the mount. To adjust level, adjust the left

or right top screw to achieve desired level of the display.

Once level, secure the lower left and right security screws

on the bracket to “fix” the mount to the wall mount.

Page 9

www.mounts.com | North America 800.368.9700 | International +1-714-632-7100

Installation Guide

AM100

13 We recommend where possible that the power and signal

cables be run separately through the mount until mating at

the display plug in points to minimize possible “cross talk”

interference. With the covers removed, cable can be run

inside the upper and lower main arm and through the slots

behind the plastic beauty covers.

12 Tilting of the display on the mount is easily accomplished by

placing one hand on top of the display edge center and one

hand on the bottom of the display edge center and gently

pulling out on the top edge to the desired tilt angle. No lock-

ing of the set tilt angle is required as the mount has built-in

friction control. If additional tension is required, use the

socket and M4 allen key to adjust the desired tension.

Extra tension can be applied to the pivot of the arms by

tightening the nuts on the arm with supplied 10mm deep

socket, and the set screws on the base with the supplied

2.5mm allen key. NOTE: Do not over tighten.

10mm Deep Socket

M2.5 Allen key

Page 10

Altri manuali per AM100

Indice

Altri manuali Premier Mounts Rack e supporto

Premier Mounts

Premier Mounts Press and Release LMVP Manuale utente

Premier Mounts

Premier Mounts Universal Flat-Only Mount UFM Manuale utente

Premier Mounts

Premier Mounts INW-AM200 Manuale utente

Premier Mounts

Premier Mounts RTM-L Manuale utente

Premier Mounts

Premier Mounts Convergent Series Manuale utente

Premier Mounts

Premier Mounts LMVLF Manuale utente

Premier Mounts

Premier Mounts CONVERGENT SAM-IFJ Series Manuale utente

Premier Mounts

Premier Mounts AM225 Manuale utente

Premier Mounts

Premier Mounts LPSA3747 Manuale utente

Premier Mounts

Premier Mounts EST200 Manuale utente

Premier Mounts

Premier Mounts PRC Manuale utente

Premier Mounts

Premier Mounts AM500 Manuale utente

Premier Mounts

Premier Mounts PRF Manuale utente

Premier Mounts

Premier Mounts CONVERGENT TVF Series Manuale utente

Premier Mounts

Premier Mounts PSM-442T Manuale utente

Premier Mounts

Premier Mounts MVWS-3X3 Series Manuale utente

Premier Mounts

Premier Mounts UNI Manuale utente

Premier Mounts

Premier Mounts BW-BASE Manuale utente

Premier Mounts

Premier Mounts Universal Tabletop Stand PSD-TTS Guida

Premier Mounts

Premier Mounts ECM-3763D Manuale utente

Premier Mounts

Premier Mounts RFM Manuale utente

Premier Mounts

Premier Mounts MVWC-3X3 Manuale utente

Premier Mounts

Premier Mounts PSPK Manuale utente

Premier Mounts

Premier Mounts PBC-UM Series Manuale utente

Manuali Rack e supporto popolari di altre marche

Salamander

Salamander Acadia AC/W/L400/WH Manuale utente

Fohhn

Fohhn VAT-09 Guida utente

ricoo

ricoo FS0522 Manuale utente

AMSOIL

AMSOIL BMK-22 Guida rapida

Kargo Master

Kargo Master 48220 Manuale utente

Milestone AV Technologies

Milestone AV Technologies SIMPLICITY SLF2 Manuale utente

ricoo

ricoo S1222 Manuale utente

Ready-Set-Mount

Ready-Set-Mount RSMCM602 Manuale utente

VidaBox

VidaBox VB MNT FFS2 Manuale utente

Welch Allyn

Welch Allyn 48960 Manuale utente

Arkon

Arkon CM035-ST-2 Manuale utente

PROEL

PROEL PLWIN60C Manuale utente

Agilent Technologies

Agilent Technologies E2609B Manuale utente

Mustang

Mustang MV-ARM4 Manuale utente

Mounting Solutions

Mounting Solutions WRM-320 Manuale utente

Pyle

Pyle PMKSPAD1 Manuale utente

ShelterIt

ShelterIt 21208 Manuale utente

SPL

SPL RackPack?4 1040 Manuale utente