Primera FX400 Manuale utente
PrinterandStand
InstallSoftwareandSetuptheStand
InstallMedia
DesignandPrint
AdjustingOffsets
Introduction
511211-030409
2
Table of Contents
1. SoftwareInstallandStandSetup 3
2. Install Foil or Laminate 7
3. Design, Print and Imprint
a. DesigntheLXLabel 11
b. DesigntheFoilLabel 11
c. Design a Laminate Label 12
d. PrintwithPTFoilSoftware 12
4. Adjustingoffsets 15
5. Foil/LaminateOnly 17
6. Specifications 19
3
Introduction:
Thank you for purchasing the FX400 metallic foil and laminate thermal printer. You
can use your FX400 with a Primera LX400, LX800 or LX810 printer. Using your LX
printer and the FX400 you can first print a full color label and print gold or silver
borders, accents, and text or laminate the label to protect against water and fading.
For the purposes of this manual the LX400, LX800 or LX810 will collectively be
referred to as the “LX Printer”. Metallic Foil or laminate will be collectively referred
to as “media”.
Section 1: Install Software and Setup the Stand
A. Install Software:
You must first install the Primera PTFoil software and the
FX400 driver.
1. Place the Installation Disc in the computer CD-ROM drive.
The Installer application will automatically launch in a few
moments.
2. Follow the prompts to install the print software.
Note: If the Installer does not start, open My Computer on your desktop. Double-
click the icon of the appropriate CD/DVD drive containing the Software Installer
disc. Double-click Installer.exe.
3. Connect power to your FX400.
4. Connect the FX400 to your PC with your beige USB 2.0 Cable.
After a few moments, Windows will tell you it has found new
hardware and is looking for software to install it.
4
Choose “No, not this time” and then click next. Next, select "Install the software
automatically" and follow the wizard to complete the installation.
You will be prompted that the software has not passed Windows Logo Testing.
You must click Continue Anyway to finish the installation.
B. Setup the Stand:
The stand is designed to easily support the LX Printer and the FX400. The stand is
separated into two parts for shipping purposes. Remove these two parts and the
FX 400 from the box. Follow the instructions below to setup the stand.
1. Place the stand pieces on a flat, level surface such as a desk or table as shown
in the diagram below. You will need at least 40 inches of horizontal space, 16
inches of depth and 30 inches of vertical space.
5
2. Attach the stand pieces together using the included screws. Do not tighten the
screws. The stand may need adjustment once the printers are in place. The LX
printer stand (larger stand) should be on the left side.
3. Place the LX printer on the larger stand. There are two sets of indents in the top
of the stand which correspond to the rubber feet of the LX printer. Place the LX400
on the smaller set of indents. Place the LX800/810 on the larger set of indents.
LX400 Indents LX800/810 Indents
4. Connect power, install ink cartridges and label stock into your LX printer
according to the printer’s manual.
Front of Printer
Front of Printer
6
5. Place the FX400 onto the smaller stand. There are also four indents on the
FX400 stand that correspond to the rubber feet on the FX400.
6. Connect power and USB to the FX400 using the included power cord and
converter.
7. Your printers are now ready for printing.
7
Section 2: Install Foil or Laminate
Install only Primera approved media. Other media may have thermal properties
that may not be compatible with the FX400. Follow these instructions to install the
media.
1. Push down on the ribbon access window to release the lock. Lift the window to
access the ribbon area.
2. The FX400 comes with two rewind/supply spindles and these can be used
interchangeably.
8
3. The media will come with two cores. One will have the media supply (foil or
laminate) and the other will be an empty core. Insert one of the spindles into the
empty core. This will be the rewind core.
4. Insert the remaining spindle into the media supply core. Note the position of the
loose end of the media in the diagram below. It should be coming off the supply
toward the back of the printer.
5. Place the media rewind core on the front set of hubs. The flange on the spindle
should be on the right side of the printer. First, insert the left side of the core onto
the spring-loaded hub. Then, place the right side of the core on the hub.
9
6. Place the media supply core on the back set of hubs. The flange on the spindle
should be on the right side of the printer. First, insert the left side of the core onto
the spring-loaded hub. Then, place the right side of the core on the hub.
7. Open the top cover of the printer. Release the cover lock by pulling forward on
the cover release levers and lift up on the cover to open.
10
8. Pull the loose end of the media from the supply core over the print head. Feed it
back toward the rewind core. Attach the loose end on the media to the rewind core
using tape or the adhesive strip on the rewind core.
Note: Make sure the media is flat against the print head with no folds or wrinkles.
Indice
Altri manuali Primera Stampante
Primera
Primera Eddie PT-E763-001 Manuale utente
Primera
Primera RX900e Manuale utente
Primera
Primera Inscripta Manuale utente
Primera
Primera Bravo Pro Manuale utente
Primera
Primera CD Color Printer II Manuale utente
Primera
Primera Signature Manuale utente
Primera
Primera Bravo SE Manuale utente
Primera
Primera trio Manuale utente
Primera
Primera BravoTM Manuale utente
Primera
Primera SignatureEVO Manuale utente
Primera
Primera DP-4100 Manuale utente
Primera
Primera Automated Optical Disc Duplication & Printing System... Manuale utente
Primera
Primera FX500E Manuale utente
Primera
Primera BravoPro Automated Optical Disc Printing... Manuale utente
Primera
Primera BravoPro Optical Disc Printing System Manuale utente
Primera
Primera Pictura 310cs Manuale utente
Primera
Primera CD/DVD Printer 6 Manuale utente
Primera
Primera Primera Signature Z1 Manuale utente
Primera
Primera Digital Color Label Press CX1200e Manuale utente
Primera
Primera EP-100 Manuale utente
