Pro-Form PFEVEL75108.0 Manuale utente

USERʼS MANUAL

CAUTION

Read all precautions and instruc-

tions in this manual before using

this equipment. eep this manual

for future reference.

QUESTIONS?

As a manufacturer, we are commit-

ted to providing complete customer

satisfaction. If you have questions,

or if there are missing parts, please

addresses listed below:

Call: 08457 089 009

Outside U : 0 (44) 113 3877133

Fax: 0 (44) 113 3877125

E-mail: [email protected]

Write:

ICON Health & Fitness, Ltd.

Unit 4

Revie Road Industrial Estate

Revie Road, Beeston

Leeds, LS11 8JG,

Model No. PFEVEL75108.0

Serial No.

Write the serial number in the

space above for reference.

Serial

Number

Decal

TABLE OF CONTENTS

WARNINGDECA P ACEMENT ..............................................................2

IMPORTANTPRECAUTIONS ................................................................3

BEFOREYOUBEGIN ......................................................................4

ASSEMB Y ...............................................................................5

HOWTOUSETHEE IPTICA EXERCISER ..................................................12

MAINTENANCEANDTROUB ESHOOTING ...................................................18

EXERCISEGUIDE INES ...................................................................19

PART IST ..............................................................................20

EXP ODEDDRAWING ....................................................................22

ORDERINGREP ACEMENTPARTS ..................................................BackCover

PROFORM is a registered trademark of ICON IP, Inc.

WARNING DECAL PLACEMENT

This drawing shows the location(s) of

the warning decal(s). If a decal is miss-

ing or illegible, call the telephone

number on the front cover of this

manual and request a free replace-

ment decal. Apply the decal in the

location shown. Note: The decal(s)

may not be shown at actual size.

WARNING: To reduce the risk of serious injury, read all important precautions and

instructions in this manual and all warnings on your elliptical exerciser before using your elliptical

exerciser. ICON assumes no responsibility for personal injury or property damage sustained by or

through the use of this product.

IMPORTANT PRECAUTIONS

1. Before beginning any exercise program,

consult your physician. This is especially

important for persons over the age of 35 or

persons with pre-existing health problems.

2. It is the responsibility of the owner to ensure

that all users of the elliptical exerciser are

adequately informed of all precautions.

3. Your elliptical exerciser is intended for home

use only. Do not use your elliptical exerciser

in a commercial, rental, or institutional set-

ting.

4. eep your elliptical exerciser indoors, away

from moisture and dust. Place your elliptical

exerciser on a level surface, with a mat

beneath it to protect the floor or carpet.

Make sure that there is enough clearance

around your elliptical exerciser to mount,

dismount, and use it.

5. Inspect and properly tighten all parts regu-

larly. Replace any worn parts immediately.

6. eep children under age 12 and pets away

from your elliptical exerciser at all times.

7. Your elliptical exerciser should not be used

by persons weighing more than 250 lbs.

(113 kg).

8. Wear appropriate exercise clothes when

exercising; do not wear loose clothes that

could become caught on your elliptical exer-

ciser. Always wear athletic shoes for foot

protection.

9. Hold the handgrip pulse sensor or the handle-

bars when mounting, dismounting, or using

your elliptical exerciser.

10. eep your back straight while using your

elliptical exerciser; do not arch your back.

11. The pulse sensor is not a medical device.

Various factors, including the userʼs move-

ment, may affect the accuracy of heart rate

readings. The pulse sensor is intended only

as an exercise aid in determining heart rate

trends in general.

12. When you stop exercising, allow the pedals

to slowly come to a stop.

13. If you feel pain or dizziness while exercising,

stop immediately and cool down.

14. Use your elliptical exerciser only as

described in this manual.

BEFORE YOU BEGIN

Thank you for selecting the revolutionary PROFORM®

COMPACT TRAINER elliptical exerciser. The COM-

PACT TRAINER elliptical exerciser provides a wide

array of features designed to make your workouts at

home more effective and enjoyable—and when youʼre

not exercising, the unique COMPACT TRAINER ellipti-

cal exerciser can be folded out of the way.

For your benefit, read this manual carefully before

you use the elliptical exerciser. If you have ques-

tions after reading this manual, please see the front

cover of this manual. To help us assist you, note the

product model number and serial number before con-

tacting us. The model number and the location of the

serial number decal are shown on the front cover of

this manual.

Before reading further, please familiarize yourself with

the parts that are labeled in the drawing below.

Handgrip Pulse Sensor

Handlebar

Pedal Disc

Wheel

Pedal

Console

Water Bottle Holder*

eveling Foot

Handle

Storage atch

Storage Magnet

Pedal Arm atch

*Water bottle is not included

ASSEMBLY

Assembly requires two persons. Place all parts of the elliptical exerciser in a cleared area and remove the

packing materials. Do not dispose of the packing materials until assembly is completed. In addition to the

included tools, assembly requires a Phillips screwdriver , an adjustable

wrench , and a rubber mallet .

As you assemble the elliptical exerciser, use the drawings below to identify small parts. The number in parenthe-

ses below each drawing is the key number of the part, from the PART IST near the end of this manual. The

number following the parentheses is the quantity needed for assembly. Note: Some small parts may have

been preassembled. If a part is not in the hardware kit, check to see if it has been preassembled.

M10 x 128mm Patch Screw (83)–2

M4 x 14mm

Screw (104)–8

M8 Jamnut

(79)–5

M8 Washer

(88)–6

Wave Washer

(111)–2

M8 x 23mm Patch

Screw (84)–4

M8 Split Washer

(90)–3

M8 x 41mm Button

Bolt (78)–4

M4 x 16mm

Round Head

Screw

(101)–14

M4 x 32mm Round

Head Screw

(105)–6

M4 x 45mm Screw

(108)–2

M8 x 23mm Shoulder

Patch Screw (115)–4

M8 x 70mm Button

Bolt (80)–1

M10 x 82mm Patch Screw

(82)–2

Hub Patch Screw

(87)–8

Star Washer

(112)–8

Transport Handle

Screw (97)–4

Bearing Spacer

(113)–4

While another person lifts the Base (1), attach the

Front Stabilizer (6) to the Base with two M10 x

82mm Patch Screws (82).

2. Remove the indicated screw and the shipping

bracket from the Base (1). Discard the screw and

the shipping bracket.

Next, tighten the Base Foot (26) into the Base (1)

as far as possible.

3. Attach the Rear Stabilizer (7) to the Frame (2) with

two M10 x 128mm Patch Screws (83).

Next, hold the handle on the Frame (2) and press

the atch Button (68). Then, lower the Frame until

the Rear Stabilizer (7) rests on the floor.

Shipping

Bracket

Screw

383

Handle

To make assembly easier, read the information

on page 5 before you begin assembling the

elliptical exerciser.

4. Hold a Hub Cover (75) and a Crank Arm (36)

against the left Crank Hub (38). Align the holes in

the Hub Cover and the Crank Arm with the unused

holes in the left Crank Hub. Next, insert four Hub

Patch Screws (87) into the Hub Cover and the

Crank Arm, and finger tighten the Hub Patch

Screws into the left Crank Hub. Tighten one Hub

Patch Screw, and then tighten the Hub Patch Screw

across from the first Hub Patch Screw. Then, tight-

en the remaining two Hub Patch Screws.

Repeat this step on the right side of the elliptical

exerciser; make sure that the Crank Arms (36)

are oriented so the Crank Bushing Sleeves (43)

are in the positions shown. Note: There are no

Pulley Screws (98) on the right side.

5. Identify the eft and Right Stabilizer Covers (71,

64), which are marked with “ eft” and “Right” stick-

ers.

Attach the eft and Right Stabilizer Covers (71, 64)

around the Base (1) with six M4 x 16mm Round

Head Screws (101).

101

7. The Console (5) can use four 1.5V “D” batteries;

alkaline batteries are recommended. IMPORTANT:

If the Console has been exposed to cold temper-

atures, allow it to warm to room temperature

before inserting batteries. Otherwise, you may

damage the console displays or other electronic

components. Remove the battery cover, insert the

batteries into the battery compartment, and reattach

the battery cover. Make sure to orient the batter-

ies as shown by the diagram inside the battery

compartment.

Battery

Cover

Batteries

Tab

8. While another person holds the Console (5) near

the Upright (3), connect the wire harness on the

Console to the Upper Wire Harness (48). Insert the

excess wire harness into the Upright. Next, attach

the Console to the Upright with four M4 x 16mm

Round Head Screws (101). Be careful to avoid

pinching the wire harness.

101

Wire

Harness

6. While another person holds the Upright (3), connect

the Upper Wire Harness (48) to the ower Wire

Harness (49). Gently pull the upper end of the

Upper Wire Harness to remove any slack, and

insert the Upright into the Base (1). Attach the

Upright with an M8 x 70mm Button Bolt (80), an M8

Split Washer (90), and an M8 Jamnut (79). Do not

tighten the Button Bolt yet; make sure that the

Jamnut is in the hexagonal hole in the Base.

Next, finger tighten two M8 x 23mm Patch Screws

(84) with two M8 Split Washers (90) into the Base

(1). Do not tighten the Button Screws yet.

Attach the Water Bottle Holder (22) to the Base (1)

with two M4 x 14mm Screws (104).

104

10. Identify the eft Handlebar (8) and the eft Upper

Body Arm (11), which are marked with “ eft” stickers.

Orient the eft Handlebar (8) and the eft Upper

Body Arm (11) as shown. Insert the eft Handlebar

into the eft Upper Body Arm. Attach the eft

Handlebar with two M8 x 41mm Button Bolts (78)

and two M8 Jamnuts (79). Make sure that the

Jamnuts are in the hexagonal holes.

Attach the Right Handlebar (9) to the Right Upper

Body Arm (12) in the same way.

Hexagonal

Holes

17 110

101

116

9. Orient the Transport Handle (116) as shown, and

attach it to the Upright (3) with four Transport

Handle Screws (97).

Identify the eft and Right Upright Covers (17, 110),

which are marked with “ eft” and “Right” stickers.

Attach each Upright Cover (17, 110) to the Upright

(3) with two M4 x 16mm Round Head Screws (101).

13. Identify the eft Pedal (13) and the eft Pedal

eg (14), which are marked with “ eft” stickers.

Attach the eft Pedal (13) to the eft Pedal eg (14)

with an M4 x 45mm Screw (108), three M4 x 14mm

Screws (104), and four Star Washers (112).

Attach the Right Pedal (not shown) to the Right

Pedal Leg (not shown) in the same way.

104

112 112

108

12. Hold the eft Front Handlebar Cover (18) and the

eft Rear Handlebar Cover (19) around the eft

Upper Body Arm (11). Attach the Handlebar Covers

with three M4 x 32mm Round Head Screws (105).

Attach the Right Front Handlebar Cover (20) and

the Right Rear Handlebar Cover (21) around the

Right Upper Body Arm (12) in the same way.

105

11. Insert the Pivot Axle (74) into the Upright (3) and then

center it. Apply a generous amount of the included

grease to the Pivot Axle.

Orient the eft Upper Body Arm (11) as shown, and

slide it onto the left end of the Pivot Axle (74). Slide

the Right Upper Body Arm (12) onto the right end of

the Pivot Axle.

Tighten an M8 x 23mm Patch Screw (84) with an M8

Washer (88) and a Wave Washer (111) into each end

of the Pivot Axle (74). Make sure that the Wave

Washers are on the ends of the Pivot Axle.

111

84 111

Grease

Indice

Altri manuali Pro-Form Ellittica

Pro-Form

Pro-Form SMART STRIDER Manuale utente

Pro-Form

Pro-Form PFEL8947.0 Manuale utente

Pro-Form

Pro-Form 310 E Elliptical Manuale utente

Pro-Form

Pro-Form Hybrid Trainer PFEL03812.2 Manuale utente

Pro-Form

Pro-Form 545e Manuale utente

Pro-Form

Pro-Form 470 Hr Elliptical Guida utente

Pro-Form

Pro-Form 510 E Elliptical Manuale utente

Pro-Form

Pro-Form XP THINLINE 480 Manuale utente

Pro-Form

Pro-Form PFEL6905.1 Manuale utente

Pro-Form

Pro-Form 470 Hr Elliptical Manuale utente

Pro-Form

Pro-Form Comfort Stride Manuale utente

Pro-Form

Pro-Form 800 Hr Heart Rate Control Elliptical Manuale operativo e di manutenzione

Pro-Form

Pro-Form PFEL29220 Manuale utente

Pro-Form

Pro-Form 300 Zle Elliptical Manuale utente

Pro-Form

Pro-Form 590e Elliptical Manuale utente

Pro-Form

Pro-Form 1150 RXW Manuale utente

Pro-Form

Pro-Form PCTL50070 Manuale utente

Pro-Form

Pro-Form 6.0 Ce Elliptical Manuale utente

Pro-Form

Pro-Form PFEL15910.1 Manuale utente

Pro-Form

Pro-Form 18.0 Re Elliptical Manuale utente

Pro-Form

Pro-Form 696 Elliptical Guida rapida

Pro-Form

Pro-Form 910 E Elliptical Manuale utente

Pro-Form

Pro-Form 450 Hr Elliptical Manuale utente

Pro-Form

Pro-Form PFEL04900 Manuale utente

Manuali Ellittica popolari di altre marche

Weslo

Weslo Momentum 4.0 Elliptical Manuale operativo e di manutenzione

Progear Fitness

Progear Fitness Air elliptical pro 1307 Manuale utente

Torque Fitness

Torque Fitness XPLLP Manuale utente

Octane Fitness

Octane Fitness PRO3700C Manuale utente

Xterra

Xterra FS5.8e Manuale utente

Bodyguard

Bodyguard E-40 Manuale utente

Bonn Germany

Bonn Germany Concept 2.2 Manuale utente

Precor

Precor Resolute RSL 620 Manuale utente

NordicTrack

NordicTrack E 9.2 Elliptical Manuale utente

Vision Fitness

Vision Fitness X6600iNetTV Manuale utente

Matrix

Matrix MX-A5x Manuale utente

SportsArt Fitness

SportsArt Fitness ECO-NATURAL Elite E874 Manuale utente

Sears

Sears FREE SPIRIT C249 30737 0 Manuale utente

True

True FS-64 Manuale utente

Sport-thieme

Sport-thieme ST 310 Manuale utente

VIRTUFIT

VIRTUFIT CTR 1.1 Manuale utente

Kettler

Kettler GIRO C 1 Manuale utente

CIRCLE FITNESS

CIRCLE FITNESS E7 Manuale utente