pro user APB100 Manuale utente
1
WIRELESS REAR VIEW CAMERA SYSTEM
WITH MIRROR DISPLAY
KABELLOSES INNENSPIEGEL RÜCKFAHR-
KAMERA-SYSTEM
SYSTÈME DE CAMERA DE RECUL SANS FIL
DRAADLOOS CAMERASYSTEEM
With bui t-in 3,5 inch monitor
mit integriertem 3,5” Monitor
avec écran 3,5 pouces
met 3,5 inch monitor
APB100
2
INTRODUCTION
The Pro-User APB100 is member of the family of advanced car Rear view back-up
systems manufactured by Pro User nternational Ltd.
The Pro-User Wireless Rear view Camera System, when used as described, will improve
your ability to see behind your car, camper, trailer, or mini-van. We have taken
numerous measures in quality control to ensure that your product arrives in top condition,
and will perform to your satisfaction.
P ease carefu y read and fo ow the fo owing safety and operating instructions.
IMPORTANT SAFETY INSTRUCTIONS
Before You Insta
f you are not confident working with 12 volt DC vehicle wiring, removing and reinstalling
interior panels, carpeting, dashboards or other components of your vehicle, contact the
vehicle’s manufacturer, or consider having the camera system professionally installed.
Interference
This device, as well as all other wireless devices, may be subject to interference.
nterference may be caused by cell phones, Bluetooth headsets, Wi-F routers, power
lines and other various electrical equipment, etc.
Repair
The camera system should not be opened. Any attempt at modification or repair by the
user will entail the loss of your guarantee.
PARTS
1. Rear View Mirror 2. Camera with mounting plate
3. Transmitter Box 4. Mounting Accessories 5. Mirror Power Cable with
cigarette plug
6. Transmitter Box Power Cable 7.Mirror mounting magic tape 8. Mirror power cable
3
INSTALLATION
These instructions do not app y to a vehic es. They are on y meant as a genera
guide due to the number of different makes & mode s. For vehic e specific
questions contact your vehic e’s manufacturer.
Camera insta ation
There are several ways to mount the camera on the back of your car. But the most
convenient is to mount it near the license plate of the car. Supplied is one mounting plate
that can be fixed behind the license plate, and the mounting plate have been installed in
the camera.
The camera is tiltable, camera angle can be adjusted manually on vertical direction.
Make
sure that its field of view and detection are not obstructed.
At some type of cars it is not possible to mount the camera near the license plate. You
may have to find another spot at the back of your car to mount the camera.
1. Remove the rear license plate, and then loosen the license plate bolts/screws.
2. Position the supplied mounting plates (with camera together) behind the license plate
bracket. Secure both license plate bracket and mounting plates with the license plate
bracket bolts/screws.
4
3. Mount the license plate on the license plate bracket.
4. Choose a routing path for the camera’s power cable through the vehicle’s body to the
reverse light circuit. f in doubt, seek professional installation assistance.
5. Some vehicles may have a hole available to pass the wire through, such as where the
license plate light is mounted, or you can drill a hole close to where the power cable
is attached to the camera. Once you have chosen where the cable will enter the
vehicle’s body, remove the camera. If you are able to use an existing opening, skip
the next two steps.
6. Before you drill a hole you MUST CHECK and see WHAT S BEH ND WHERE YOU ARE
DR LL NG. f there are any vehicle components, such as electrical parts or fuel
system components behind where you are drilling, you must take whatever
precaution is necessary not to damage them. Remove the license plate and camera
before drilling.
7. After you have drilled the hole, insert the supplied grommet, then pass the camera
cables through the grommet into the vehicle. You must use the grommet to prevent
the metal edge of the hole from cutting the camera cable.
8. Mount the transmitter box inside the trunk. Connect the camera’s power cable and
the transmitter box power cable to the transmitter box.
9. Next you’ll need to find the vehicle’s reverse lights. Turn the vehicle’s ignition key to
the accessory position, engage the parking brake and put the car in reverse. Look at
the vehicle’s tail lights to see where the reverse lights are located, they are the white
lights. To locate the reverse light’s 12V+ wire it will be necessary to gain access to
the rear of the vehicle’s tail light. For help locating the vehicle’s reverse light circuit
contact your vehicle’s manufacturer for vehicle specific wiring diagrams.
10. Once you have located the reverse light circuit you will have to route the transmitter
box power cable to that location. You must securely fasten the power cable to prevent
it from being caught on any vehicle component such as the trunk hinge. Never route
the cable on the outside of the vehicle!
5
11. The reverse light sockets on
most vehicles have two wires
connected to them. Usually the
negative wire is black and the
positive wire is a colored wire. f
you are uncertain about the
wiring, you can use a 12 volt
multimeter available at most
auto parts stores to determine
which is the positive wire. Follow
the manufacturer’s instructions
for the safe use of the
multimeter.
12. After determining which wire is
the positive and which is the negative, turn off the ignition key, then remove the
battery’s negative cable.
13. Splice the red wire using the supplied in-line wire connectors to the reverse light’s
positive (+) wire. Use a set of slip joint pliers to squeeze the TAP and insure good
connection.
14. Next splice the black wire of the transmitter box power cable to the reverse light’s
negative (-) wire or ground.
15. Replace the reverse light bulb, and then re-install the light socket. Secure all the
wires with cable ties or electrical tape.
16. Re-attach the negative battery cable to the battery.
Rear View Mirror Insta ation
When mounting the mirror, please double check the width of your car’s rear view mirror≤
80mm to avoid cannot be installed.
1. Place the spring loaded top clips underneath the car’s existing rear view mirror.
2. Press down the mirror extend the bottom clips, then tilt the mirror towards the
existing rear view mirror.
6
3. Left the spring loaded clips close around the mirror. Adjust the Rear View Mirror for
the best rear view.
4. Tighten the magic tape to fix the position.
Remark: Please make sure the male and female of the magic tape are matched perfectly
before you connect the metal buckle of the magic tape to the main unit, once you
connect them, you can not pull the metal buckle out.
5. Choose a Location and nstall Power Cable as below alternative methods showed in
the pics:
a. Choose a location on windshield or dashboard of your car, where does not obstruct
your vision.
b. nsert the small 12 Volt DC plug of the power cable into the top of the mirror.
c. Connect the Cigarette DC plug cable (provided) with the cigarette lighter socket/12V
power outlet of vehicle.
7
Remark: The cable must not interfere the safe operation of the vehicle.
For professional installation, refer to the illustration above, if doubt please seek
professional assistant.
8
NOTE: UNDER EXTREME BR GHT L GHT COND T ONS, THE SCREEN MAGE MAY TAKE A
FEW SECONDS TO STABL ZE. PLEASE WA T UNT L THE MAGE HAS STABL ZED BEFORE
BACK NG UP.
System testing
1. Reattach the vehicle’s negative battery cable.
2. Turn the ignition key to the accessory position, do not start the vehicle.
3. Engage the parking brake, and then put the shifter in the reverse position.
After testing the unit and you are satisfied with the route you have chosen for the cabling,
you must permanently install it.
Route all wires behind interior panels or under carpeting so they are hidden. Use supplied
cable ties to neatly gather any excess wire.
9
OPERATION
The mirror will automatically turn on when the vehicle is in reverse gear.
There are 5 control buttons available for users to have their controls:
Power button
Press the POWER button to supply power to the mirror. When the mirror image is on, the
blue LED(beneath the power button) will be off. f there is power to the mirror, but the
mirror image is OFF, the blue LED will on. When the monitor power is off, no picture can
appear on the screen and the blue LED will be off.
Menu button
Press the Menu button to enter the menu screen as shown below:
Repeat pressing the Menu button to select Brightness,
contrast or co our of the picture.
Press the + button or – button to adjust settings within
the control selected. Press the + button to increase the
value and press the – button to decrease the value.
To exit the menu screen, select exit on the screen using the MENU button and press
either + or – to exit the menu screen.
Guide ine button
The unit has the option to show distance-guidelines on
the display. This helps you to visually see the distance
between the objects behind your car. By pressing the
guideline button, you can switch this option on and off.
10
TECHNICAL SPECIFICATIONS
Camera
Operating Voltage 12V DC
Current consumption(include transmitter box） <180mA
mage sensor CMOS
No. of pixel 640x480
Resolution （Horizontal） >330 TVL
Optical lens 2,4mm / F2,1
Wire ess transmitter
Transmission frequency 2468MHz
RF transmission distance (open space) >80M
LCD monitor
Operation Voltage 12V DC
Standby Current <65mA
Operation Current <350mA
LCD display screen size 3,5inch
No. of pixel 320x240
Operation temperature -10 to +45 degree Celsius
ENVIRONMENTAL PROTECTION
Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or
retailer for recycling advice.
WARRANTY
Pro-User warrants this product for a period of 2 years from the date of purchase to the
original purchaser. Warranty is not transferable. Warranty covers defect against
workmanship and materials only. To obtain warranty service, please return the unit to
the place of purchase or authorized Pro-User dealer together with your proof of purchase.
The warranty is void if the product has been damaged or not used as described in this
manual. Warranty is void if a non-authorized repair has been performed. Pro-User makes
no other warranty expressed or implied. Pro-User is only responsible for repair or
replacement (at Pro-Users’ Discretion) of the defective product and is not responsible for
any consequential damage or inconvenience caused by the defect.
Indice
Lingue:
Altri manuali pro user Telecamera da cruscotto
