PROAIM Cinema Series Comet Manuale utente
1
What’s In The Box
Please inspect the contents of your shipped package to ensure you have received everything that
is listed below.
Comet 12 Euro Cinema Jib (JB-COMT)
Assembly Manua l
Proaim 7 Comet Jib
1 x 3 Extension Arm
2 x Counterweight Rods
1 x 3 Extension Rod
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
NOTE: If you have purchased (JB-COMT-01) kit, you will receive the following:
2
Insert Levelling Support Feet on all 4 corners
of Ridgeline Dolly. Secure them with a ring.
Insert Lever onto Levelling Support to adjust
the length of feet from ground. Then lock
the Support with knob.
Apply the Front Wheel Brakes while
assembling to ensure double security. Insert
Steering Push/Pull Bar into Dolly’s Rear-axle.
Ridgeline Dolly Setup
Fix screw into the Steering and lock from
both sides to secure Steering accurately.
NOTE: To avoid unwanted accident while assembling the crane, please assemble the dolly with
supporng feet. It also increases the stability.
Ridgeline Dolly With
4 x Levelling Support Feet
Centre Column
NOTE: If you have purchased (JB-COMT-02) kit, you will also receive the following:
3
Place lower secon of Centre Column onto
the Dolly. Twist the Column to align all its
corners with screws. Tighten them back to
secure it.
Aaching the Centre Column
Place Centre Column onto the centre of
dolly. Insert & ghten screws on all corners
to secure the Column.
Place Comet Jib onto the Euro-adapter of
Centre Column.
Fix the Jib fork with Centre Column by
locking the knob via locking lever.
Lock both the pan knob to assemble the jib
crane.
Jib Crane Setup
4
Loosen knob on top located on the back
(operator) side of jib. Then take out the side
knob.
Insert Counterweight Rod through the holes
and lock the knob on top. Then add weights
(Not Included) to both the Rods as per the
requirement and secure them with Locking
Pin.
Loosen the knob on Adjustment
Counterweight and slide it to ensure right
balance of jib, as shown in image.
Loosen side knob on the front (camera) side
of jib and the red buon knob on Rod, to
remove the camera mounng secon.
Now loosen boom knob on the front
(camera) side of jib and press the small red
buon on side to release (pull-out) the
Telescopic Secon.
Pull out the Telescopic Secon from back
(operator) side of jib. Insert the side knob
again to lock it.
5
Then press the laer small red buon on
steel Rod to release (pull-out) the Telescopic
Secon of Rod.
Then aach Extension Rod of 3 with
Telescopic Secon of Rod and lock with the
red buon knob appropriately to secure it.
Now insert camera mounng secon into
the Extension Arm and Rod.
Tighten side knob of jib and red buon knob
on Rod to lock the mounng secon
accurately.
Aach 3 Extension Arm with Telescopic
Secon and lock the knob appropriately to
secure it.
NOTE: You can precisely balance the
plaorm with its unique Levelling
Mechanism on Rod.
Finally, mount your camera setup as desired,
on Double Euro Adapter provided with the
mounng secon of jib.
6
7.3 Jib Length– When jib length is 7.3 Jib will be balance with 12.5kg weight, with every 2kg
of camera setup you need to add 4.5kg weight to balance it. Now total weight 12.5 + 4.5kg= 17kg.
9.1 Jib Length– When jib length is 9.1 Jib will be balance with 21.5kg weight, with every 2kg
of camera setup you need to add 4.5kg weight to balance it. Now total weight 21.5 + 4.5kg= 26kg.
12.5 Jib Length– When jib length is 12.5 Jib will be balance with 38.5kg weight, with every
2kg of camera setup you need to add 6.5kg weight to balance it. Now total weight
38.5 + 6.5kg= 45kg.
NOTE: Use Micro balance for Precission balancing.
Balancing Tips
7
YOUR PROAIM COMET CAMERA JIB CRANE
ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)
Warranty: We oer one year warranty for our products from date of purchase. Within this period of me,
we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor does it
cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspecon
and evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our
utmost support and care unl you use our product.
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali PROAIM Accessori per fotocamere
PROAIM
PROAIM CINEMA Series Manuale utente
PROAIM
PROAIM CINEMA P-SWCC-10 Manuale utente
PROAIM
PROAIM Dove Tail Manuale utente
PROAIM
PROAIM P-FT-J Manuale utente
PROAIM
PROAIM Follow Focus X1 Manuale utente
PROAIM
PROAIM P-WH-DMC Manuale utente
PROAIM
PROAIM FF-WRLS-DR Manuale utente
PROAIM
PROAIM CINEMA Series Manuale utente
PROAIM
PROAIM Wave-2 Plus Manuale utente
PROAIM
PROAIM Gravita Manuale utente
PROAIM
PROAIM P-MLMT-01 Manuale utente
PROAIM
PROAIM P-MWP-D Manuale utente
PROAIM
PROAIM CINEMA Series Manuale utente
PROAIM
PROAIM P-SMMT-01 Manuale utente
PROAIM
PROAIM FF-FCBE-01 Manuale utente
PROAIM
PROAIM Discovery SR-10 Manuale utente
PROAIM
PROAIM P-18-JS Manuale utente
PROAIM
PROAIM Falcon P-FLCN Manuale utente
PROAIM
PROAIM VI-252-00 Manuale utente
PROAIM
PROAIM P-PTBH-01 Manuale utente
