Prorack K762 Manuale utente
K762
Fitting Kit
EN Fitting Instructions for Basic Carrier
x 1 x 1 x 1 x 1
x 2 x 1 x 1 x 2
x 2
Revision No: 2A 1
Fitting Kit K762
MAX kgs (lbs)
W/P WHD
Toyota
Yaris , 5dr Hatch 10-14 ZA 50 kgs (110 lbs) 50 kgs (110 lbs)
Yaris , 5dr Hatch 10-15 US 50 kgs (110 lbs) 50 kgs (110 lbs)
Yaris , 5dr Hatch 11-14 NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
Yaris , 5dr Hatch 11-14 AU 50 kgs (110 lbs) 50 kgs (110 lbs)
Yaris , 5dr Hatch 11-14 EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Yaris , 5dr Hatch 14-+ NZ 50 kgs (110 lbs) 50 kgs (110 lbs)
Yaris , 5dr Hatch 14-+ AU 50 kgs (110 lbs) 50 kgs (110 lbs)
Yaris , 5dr Hatch 14-+ EU 50 kgs (110 lbs) 50 kgs (110 lbs)
Yaris , 5dr Hatch 14-+ ZA 50 kgs (110 lbs) 50 kgs (110 lbs)
Yaris , 5dr Hatch 15-+ US 50 kgs (110 lbs) 50 kgs (110 lbs)
2
Fitting Kit EN
K762
First Time Installation
●Remove parts from inside the package and
check. Contact your dealer if any parts are
missing or damaged.
●This kit fits type A, B, C and D.
●These instructions show type A crossbar
fitted. They also apply to type B, C and D.
NOTE: Clamp images in these instructions may
not be representative of the clamps in this kit
3
Fitting Kit EN
K762
●Use keys to remove covers.
●Use hex screwdriver to reverse adjusting
screw 10 turns.
●Press adjusting screw and pull crossbar
legs out. Refer to the crossbar instructions
for crossbar adjustment method.
●Ensure each end of the crossbar is
adjusted equally.
4
Fitting Kit EN
K762
●Remove locking screw.
●Apply protective strip as shown.
Trim if required.
●It is important to put the clamps in the
correct position on the vehicle.
●Letters refer to the part numbers stamped
on clamps.
●Clamp Part Number:
A = A217
B = A218
C = A219
D = A220
5
Fitting Kit EN
K762
●Attach clamp to each leg. NOTE; clamps
may have labels showing their positions on
the vehicle (For example; "Front Right").
●Refit locking screw so that it goes through
the hole in the clamp. Do not begin to
tighten the locking screw.
●Refer to the underside of the pad for the
part number.
6
Fitting Kit EN
K762
●It is important to put the pads in the correct
position on the vehicle.
●Letters refer to the pad part numbers and
position.
●Pad Part Number:
A = 244A
B = 293A
C = 294A
●Place rubber pads (supplied with fitting kit)
on the vehicle roof. Pad may vary in shape
to that shown.
●Make sure the pad fits into the holes
underneath the foot.
7
Fitting Kit EN
K762
Fitment
●Clamps directly to edge of roof under the
doors
●Please check the rear of this manual for
information relating specifically to your
vehicle.
●Place crossbar on vehicle. Minimum
recommended spacing between the bars is
700mm (27 1/2") (unless otherwise stated).
●Adjust the legs on the crossbar so that they
are positioned equally from the ends of the
crossbar, and the clamps engage firmly on
the body work of the vehicle.
●Tighten adjusting screw to 3 Nm (2.2 ft lb)
hand tight.
8
Fitting Kit EN
K762
●Tighten locking screw on both legs evenly,
3 Nm (2.2 ft lb).
●Check crossbar is securely attached to the
vehicle.
●Use keys to fit and lock covers
9
Fitting Kit EN
K762
CAUTION: Recheck all fasteners immediately after
a load is applied to the crossbars.
Regularly check screws are tight.
10
Indice
Altri manuali Prorack Accessori per automobili
Prorack
Prorack K537 Manuale utente
Prorack
Prorack K919 Manuale utente
Prorack
Prorack K1045 Manuale utente
Prorack
Prorack K310 Manuale utente
Prorack
Prorack K307 Manuale utente
Prorack
Prorack K907 Manuale utente
Prorack
Prorack K027 Manuale operativo e di installazione
Prorack
Prorack K902 Manuale utente
Prorack
Prorack K834 Manuale utente
Prorack
Prorack K340 Manuale utente
Prorack
Prorack K346 Manuale utente
Prorack
Prorack K720 Manuale utente
Prorack
Prorack K1221 Manuale utente
Prorack
Prorack PR3097 Manuale utente
Prorack
Prorack K049 Manuale utente
Prorack
Prorack K464 Manuale utente
Prorack
Prorack T84HALF Manuale utente
Prorack
Prorack K486 Manuale utente
Prorack
Prorack K677 Manuale operativo e di installazione
Prorack
Prorack K1001 Manuale utente
