Pyle PDWR30B Manuale utente
www.PyleUSA.com
PDWR30B
• Excellent for Use On Boats/ Marine/ Decks/ Patios/ Poolside/ Outdoors
• Completely Water Proof
• 3.5'' Aluminum Injection Cone Woofer
• 40 Oz. Magnet Structure
• 1'' High Compliance Myiar Tweeter
• Capacitor Crossover Network
• Bass Reex Vent for Added Bass Response
• Heavy Duty ASB Construction
• Quick Connect/ Disconnect Speaker Terminals
• Unique Spring Loaded Mounting System
• Removable Rustproof Mesh Grills
• Power: 150Watts RMS/ 300Watts Peak
• Frequency Response: 60-20K Hz
• Impedance: 4 Ohms
• Dimensions: 4.75''(W)x 7.25''(H) x 4.75''(D)
HOW TO INSTALL
MOUNTING THE BRACKET
4. DrIII pllot holes Into the mounting surface.
5. Gently pull the speaker wire though the wire hole in the center of the mounting bracket,
so that the holes all line up.
6. Use your hardware to attach the bracket to the mounting surface.
1. Remove the bracket knobs and the bracket from the speaker.
2. Hold the bracket up to the mounting surface. "PDWR30B
Waterproof Speakers" can be mounted either horizontally
or verticalIy, hold the bracket so that the speaker wire ts
through the large, circular wire hole in the bracket, align the
bracket to be square with the surrounding (Use A level for
accuracy)
3. Mark the locations of the three shaped screw holes, use all of
the holes.
MOUNTING
www.PyleUSA.com
FINAL ADJUSTMENTS
1. After checking that the speaker is in-phase and works correctly, angle the speaker for the
best sound.
2. Hand tighten rhe bracket knobs only, power tools may over-tighten rhe knob, and strip
the threads of the insert.
3. Check that the entire installatlon is safe and secure.
CONNECTING YOUR SPEAKERS
Connecting the speakers to your amplier or receiver.
Questions? Issues?
We are here to help!
Phone: (1) 718-535-1800
Email: suppor[email protected]
3
• First turn your amplier OFF to avoid
damage which may result from accidental
shorting of the speaker leads.
• Correct phase polarity is critical for proper
stereo imaging and bass performance.
The red (+) terminal on your amplier or
receiver must be connected to the red (+)
terminal on your speaker, the same
applies for the balck (-) terminal.
• Connect one loudspeaker at a time to
ensure proper connection of left and
right channels. Make sure all wires are
rmly fastened.
• If you notice a high lavel of bass or
central image focus, double check your
connections for proper polarity.
Indice
Altri manuali Pyle Altoparlanti
Pyle
Pyle PGRDSP62BTB Manuale utente
Pyle
Pyle PDIC6LT Manuale utente
Pyle
Pyle PPHP158BMA Manuale utente
Pyle
Pyle PWMA-970 Manuale utente
Pyle
Pyle PSUFM1288B Manuale utente
Pyle
Pyle PPHP2835B Manuale utente
Pyle
Pyle PBKSR40WT Manuale utente
Pyle
Pyle PWMA200 Manuale utente
Pyle
Pyle PPHP2814B Manuale utente
Pyle
Pyle PWPBT250 Manuale utente
Pyle
Pyle PDIC53T Manuale utente
Pyle
Pyle PPHP2845B Manuale utente
Pyle
Pyle PLMRWB652LEW Manuale operativo e di manutenzione
Pyle
Pyle PPHP874B Manuale utente
Pyle
Pyle PWRC55BT Manuale utente
Pyle
Pyle PDWR69BTB Manuale utente
Pyle
Pyle PowerSports PLUTV58BKA Manuale utente
Pyle
Pyle PPHP844B Manuale utente
Pyle
Pyle PBMSPG144 Manuale utente
Pyle
Pyle Discojam PWMA1594UFM Manuale utente
