QMS Magicolor 2 Desklaser Manuale
Conversion Instructions:
QMS magicolor 2 DeskLaser
to QMS magicolor 2 CX
®
1800502-001A
®
Trademarks
QMS, the QMS logo, and
magicolor
are registered trademarks of QMS, Inc., registered
in the United States Patent and Trademark Office.
Proprietary Statement
The digitally encoded software included with your QMS
magicolor
print system is
Copyrighted © 1998 by QMS, Inc. All Rights Reserved. This software may not be
reproduced, modified, displayed, transferred, or copied in any form or in any manner or
on any media, in whole or in part, without the express written permission of QMS, Inc.
Copyright Notice
These instructions are Copyrighted © 1998 by QMS, Inc., One Magnum Pass, Mobile,
AL 36618. All Rights Reserved. These instructions may not be copied in whole or in
part, nor transferred to any other media or language, without the express written
permission of QMS, Inc.
Introduction
1
QMS magicolor 2 DeskLaser to CX Conversion
Introduction
This kit includes all the hardware and software necessary for to
convert a QMS
magicolor
2 DeskLaser Print System into a QMS
magicolor
2 CX Print System.
Kit Contents
In addition to these instructions, your upgrade kit contains the follow-
ing items. Make sure that you have all of these items before proceed-
ing with the installation. Report any discrepancies to your QMS
vendor. Don’t return any merchandise before contacting the vendor.
nQMS
magicolor
2 CX controller board with 24 MB RAM installed
See the installation instructions in this document.
nAnti-static wrist strap
nProduct ID logo label (P/N 1241121-002)
nTwo dataplate overlay labels (P/Ns 1241198-001 and
1241202-001)
n
QMS magicolor 2 Getting Started
(hardcopy)
n
QMS magicolor 2 Documentation
CD-ROM
See the insert booklet for instructions on installing Adobe Acrobat
Reader. See the 1CONTENT.PDF file in the root for contents and
access information.
n
QMS Software Utilities
CD-ROM
See the insert booklet for instructions on installing Adobe Acrobat
Reader. See the 1CONTENT.PDF file in the root directory for
contents and access information.
nWarranty card
Conversion
Procedure
QMS magicolor DeskLaser to CX Conversion2
Conversion Procedure
Converting your QMS
magicolor
2 DeskLaser to a QMS
magicolor
2
CX Print System involves two steps:
nn Removing the
magicolor
2 DeskLaser controller board and
installing the
magicolor
2 CX controller board.
» Note:
You’ll need a Phillips screwdriver for this procedure.
nn Applying the appropriate identification labels.
nn Installing the printer driver(s).
▲Caution
:
It’s very important to protect the printer controller board
from electrostatic damage while performing this conversion.
Attach one end of the anti-static wrist band included in this kit to your
wrist and the other end to any convenient electrical ground. The bare
metal chassis of equipment, such as on the back of a computer, is
suitable if it is plugged in but turned off. Never attach the wrist strap
to any piece of equipment with an electrical current present. Turn off
all power switches first. Plastic, rubber, wood, painted metal surfaces,
and telephones are not acceptable grounding points. The printer isn’t
an acceptable grounding point either because it must be unplugged
before you perform this task.
Conversion
Procedure
3
QMS magicolor 2 DeskLaser to CX Conversion
Installing the magicolor 2 CX Controller Board
▲Caution:
The following procedure is written for the system
administrator. Do not attempt this procedure if you have no
experience working with circuit boards.
1 Turn off the printer, remove the power
cord, and disconnect all interface
cables from the printer.
2 Using a Phillips screwdriver, loosen
the two mounting screws that hold
the controller board to the printer.
3 Pull the
magicolor
2 DeskLaser con-
troller board straight out and lay it on
a flat surface.
4 Remove from its packaging the
magicolor
2 CX controller
board.
5 If you want to, remove any SIMMs from the
magicolor
2
DeskLaser controller board, and install them on the
magi-
color
2 CX controller board.
The
magicolor
2 CX control board comes standard with 24 MB of
memory. It’s not necessary to add additional memory, but you
may want to. Refer to the
QMS magicolor 2 Options
manual for
SIMM removal and installation instructions.
6 Remove from their packaging any SIMMs you purchased
separately and install them on the
magicolor
2 CX controller
board.
Again, it’s not necessary to add additional memory, but you may
want to. Refer to the
QMS magicolor 2 Options
manual for SIMM
installation instructions.
7 If you purchased any other options, such as an internal hard
disk, install them now.
Refer to the
QMS magicolor 2 Options
manual for instructions.
Conversion
Procedure
QMS magicolor DeskLaser to CX Conversion4
Verifying the Conversion
To verify the conversion, turn on the printer. A start-up page,
identifying the printer as a QMS
magicolor
2, automatically prints.
This indicates that the printer has successfully been converted from a
QMS
magicolor 2
DeskLaser to a QMS
magicolor
2 CX Print System.
Applying the Identification Labels
Use the following illustrations to install the new dataplate and product
ID logo on the printer.
Product ID Logo
8 Align the
magicolor
2 CX controller
board on the plastic guides, and then
slide it into the printer.
Make sure it’s properly seated in its con-
nectors, but do not force it.
9 Tighten the two mounting screws.
10 Reconnect the interface cables and
power cord, and then turn on the printer.
QMS magicolor 2
Product ID Logo
P/N 1241121-002
(Apply over the existing
product ID logo.)
For More
Information...
5
QMS magicolor 2 DeskLaser to CX Conversion
Dataplate
» Note:
The dataplate illustrated here is for 110 volt printers. If you have
a 220 volt printer, discard overlay P/N 1241202-001 (there is no FCC
ID line on the dataplate). In addition, the Model name for 220 volt
printers ends with a “-2” rather than a “-1.”
Installing the Printer Driver(s)
Refer to your
QMS magicolor 2 Getting Started manual
, shipped in
this conversion kit, for complete information on installing the
appropriate printer driver(s).
For More Information...
If you have any questions or problems during or after the conversion,
refer to appendix A, “QMS Customer Support,” in any QMS manual to
find out how to contact QMS.
v
MC2
Model: QMS-MCWX2-1
SN:
P
U
®
Th
P
a
(1
)
thi
s
un
P
a
P
a
Rating: 120V 50Hz-60 Hz, 8A
FCC ID: E7SMC2WX-1
MCCX2
Model overlay
P/N 1241198-001
FCC ID overlay
P/N 1241202-001
Altri manuali per Magicolor 2 Desklaser
4
Questo manuale è adatto per i seguenti modelli
1
Indice
Altri manuali QMS Stampante
QMS
QMS Magicolor 2 Desklaser Manuale utente
QMS
QMS 2060 WX Manuale utente
QMS
QMS Magicolor 330 Manuale utente
QMS
QMS 2425 Manuale di servizio
QMS
QMS Magicolor 2 Desklaser Manuale utente
QMS
QMS 1800428-001B Manuale utente
QMS
QMS 1060E Manuale di istruzioni
QMS
QMS PS 410 Manuale utente
QMS
QMS 2425 Dimensioni
QMS
QMS 2425 Manuale utente
QMS
QMS 3260 Manuale utente
QMS
QMS Magicolor WX Manuale utente
QMS
QMS 2425 Manuale utente
QMS
QMS SmartWriter 80+ Manuale utente
QMS
QMS 1725E Manuale utente
QMS
QMS Magicolor 6100 Manuale
QMS
QMS 19 Manuale utente
QMS
QMS 4060 Manuale utente
QMS
QMS Magicolor 2 plus Manuale utente
QMS
QMS Magicolor CX Manuale utente
