R&S EDST300 Manuale utente
R&S®EDST300
TACAN/DME Station
Tester
Getting Started
1179564702
Version 01
(;ÝÆ_2)
This manual applies to the following R&S®EDST300 models with software version
4.20 and later:
●R&S®EDST300 (5202.9009.02)
In addition to the base unit, the following options are described:
●R&S®EDST-B2 Low-Power Interrogator (5202.9509.02)
●R&S®EDST-B3 Internal Battery (5202.7187.02)
●R&S®EDST-B6 ADDITIONAL TRIGGER OUT (5202.9167.02)
●R&S®EDST-K1 TACAN Analysis (5202.9515.02)
●R&S®EDST-K2 Pulse Shape Analysis (5202.9521.02)
© 2023 Rohde & Schwarz GmbH & Co. KG
Muehldorfstr. 15, 81671 Muenchen, Germany
Phone: +49 89 41 29 - 0
Email: [email protected]
Internet: www.rohde-schwarz.com
Subject to change – data without tolerance limits is not binding.
R&S® is a registered trademark of Rohde & Schwarz GmbH & Co. KG.
All other trademarks are the properties of their respective owners.
1179.5647.02 | Version 01 | R&S®EDST300
Throughout this manual, products from Rohde & Schwarz are indicated without the ® symbol , e.g.
R&S®EDST300 is indicated as R&S EDST300. R&S®EDST-Bxy/-Kxy is indicated as R&S EDST-Bxy/-Kxy.
Safety and regulatory information
R&S®EDST300
3Getting Started 1179.5647.02 ─ 01
1 Safety and regulatory information
The product documentation helps you use the product safely and efficiently. Fol-
low the instructions provided here and in the following chapters.
Intended use
The R&S EDST300 is an analyzer designed for installing, testing and servicing
pulsed terrestrial navigation systems like DME and TACAN ground equipment.
Use the product only for its designated purpose. Observe the operating conditions
and performance limits stated in the data sheet.
Target audience
This document is aimed at installers, technicians and operators of the
R&S EDST300. It assumes the readers are familiar with basic handling of electri-
cal equipment and have knowledge of avionic navigation systems.
Where do I find safety information?
Safety information is part of the product documentation. It warns you of potential
dangers and gives instructions on how to prevent personal injury or damage
caused by dangerous situations. Safety information is provided as follows:
●In Chapter 1.1, "Safety instructions", on page 3. The same information is
provided in many languages as printed "Safety Instructions". The printed
"Safety Instructions" are delivered with the product.
●Throughout the documentation, safety instructions are provided when you
need to take care during setup or operation.
1.1 Safety instructions
Products from the Rohde & Schwarz group of companies are manufactured
according to the highest technical standards. To use the products safely, follow
the instructions provided here and in the product documentation. Keep the prod-
uct documentation nearby and offer it to other users.
Use the product only for its intended use and within its performance limits. Inten-
ded use and limits are described in the product documentation such as the data
Safety instructions
Safety and regulatory information
R&S®EDST300
4Getting Started 1179.5647.02 ─ 01
sheet, manuals and the printed "Safety Instructions". If you are unsure about the
appropriate use, contact Rohde & Schwarz customer service.
Using the product requires specialists or specially trained personnel. These users
also need sound knowledge of at least one of the languages in which the user
interfaces and the product documentation are available.
Reconfigure or adjust the product only as described in the product documentation
or the data sheet. Any other modifications can affect safety and are not permitted.
Never open the casing of the product. Only service personnel authorized by
Rohde & Schwarz are allowed to repair the product. If any part of the product is
damaged or broken, stop using the product. Contact Rohde & Schwarz customer
service at https://www.rohde-schwarz.com/support.
Operating the product
The product is intended for mobile use. The maximum weight of the product is
provided in the data sheet. If the product casing is not waterproof, use an ade-
quate weather protection to carry the product outdoors with you.
When using the product in a vehicle or aircraft, make sure that the product is
properly secured. If stacking is possible, secure the whole stack of products so
that they cannot fall over and cause injury.
Observe the ambient conditions such as altitude, operating temperature and cli-
matic loads; see the data sheet.
Due to their exposed location, mobile communications systems are at risk of
damage from lightning. This also poses a risk to persons nearby. Vehicles carry-
ing mobile communications systems require an electrically conductive body, a
grounded antenna and also equipotential bonding that includes the cables routed
into the vehicle.
Connecting to power
The product runs on DC voltage. For the specifications of the supply voltage for
the product, refer to the data sheet. Under normal conditions, contact with DC
voltage in this range poses a low risk of electric shock.
Take the following measures for your safety:
●If you connect the product to an external power supply, use one recommen-
ded in the product documentation.
●Before switching on the product, ensure that the voltage and frequency indica-
ted on the product match the available power source.
Safety instructions
Safety and regulatory information
R&S®EDST300
5Getting Started 1179.5647.02 ─ 01
●Only use intact cables and route them carefully so that they cannot be dam-
aged. Also ensure that nobody can trip over loose cables.
Handling batteries safely
The product contains exchangeable or built-in lithium polymer or lithium ion cells
or batteries. The use of the word battery in the following always means all types.
Only the battery contents are potentially hazardous. As long as a battery is
undamaged and the seals remain intact, there is no danger.
Impact, shock or heat can cause damage such as dents, punctures and other
deformations. A damaged battery poses a risk of personal injury. Handle a dam-
aged or leaking battery with extreme care. Immediately ventilate the area since
the battery releases harmful gases. If you come into contact with the battery fluid,
immediately remove all contaminated clothing. Irritation can occur if the battery
fluid comes in contact with your skin or eyes. Immediately and thoroughly rinse
your skin or eyes with water and seek medical aid.
For safe handling, follow these rules:
●Do not short-circuit the battery.
●Do not mechanically damage the battery. Do not open or disassemble the bat-
tery.
●Do not expose the battery to high temperatures such as open flames, hot sur-
faces and sunlight.
●Only use the battery with the designated Rohde & Schwarz product.
●Only use the appropriate Rohde & Schwarz charger to charge the batteries. If
the batteries are improperly charged, there is a risk of explosion. For charging
and discharging temperature ranges, see the product documentation.
●Replace exchangeable batteries only with the same battery type.
●Store the battery in the product or use the product packaging.
●Dispose of exchangeable batteries separately from normal household waste
as specified by the local waste disposal agency.
If you disregard these rules, you risk serious personal injury or even death due to
explosion, fire or hazardous chemical substances. The product documentation
provides further details.
If exchangeable batteries or products with built-in batteries are defective, contact
the Rohde & Schwarz customer service. Rohde & Schwarz classifies the severity
of the defect. When returning batteries or Rohde & Schwarz products containing
batteries, use a carrier qualified to transport dangerous goods and notify the car-
Safety instructions
Safety and regulatory information
R&S®EDST300
6Getting Started 1179.5647.02 ─ 01
rier of this classification. Follow the carrier’s transport stipulations in line with
IATA-DGR, IMDG-Code, ADR or RID.
Using headphones
Take the following measures to prevent hearing damage. Before using head-
phones, check the volume and reduce it if necessary. If you monitor varying sig-
nal levels, take off the headphones and wait until the signal has settled. Then
adjust the volume.
Meaning of safety labels
Safety labels on the product warn against potential hazards.
Potential hazard
Read the product documentation to avoid personal injury or product damage.
DC - direct current
Connect to a DC power supply of the specified voltage range.
1.2 Labels on the product
Labels on the casing inform about:
●Personal safety, see "Meaning of safety labels" on page 6
●Product and environment safety, see Table 1-1
●Identification of the product, see Chapter 5.3, "Device ID", on page 30:
Table 1-1: Labels regarding product and environment safety
Labeling in line with EN 50419 for disposal of electrical and electronic equipment after
the product has come to the end of its service life.
For more information, see the product user manual, chapter "Disposal".
Labeling in line with directive 2006/66/EC for disposal of batteries after they have come
to the end of their service life.
For more information, see the product user manual, chapter "Disposal".
Labels on the product
Safety and regulatory information
R&S®EDST300
7Getting Started 1179.5647.02 ─ 01
1.3 Warning messages in the documentation
A warning message points out a risk or danger that you need to be aware of. The
signal word indicates the severity of the safety hazard and how likely it will occur
if you do not follow the safety precautions.
NOTICE
Potential risks of damage. Could result in damage to the supported product or to
other property.
1.4 Korea certification class A
이 기기는 업무용(A급) 전자파 적합기기로서 판매자 또는 사용자는 이 점을 주의하
시기 바라며, 가정외의 지역에서 사용하는 것을 목적으로 합니다.
Korea certification class A
Documentation overview
R&S®EDST300
8Getting Started 1179.5647.02 ─ 01
2 Documentation overview
This section provides an overview of the R&S EDST300 user documentation.
Unless specified otherwise, you find the documents at:
www.rohde-schwarz.com/manual/EDST300
Further documents are available at:
www.rohde-schwarz.com/product/EDST300
Getting Started manual
Introduces the R&S EDST300 and describes how to set up and start working with
the product. Includes basic operations and general information, e.g. safety
instructions, etc.
A printed version is delivered with the instrument.
User manual
The user manual contains the description of all instrument modes and functions.
It also provides an introduction to remote control, a complete description of the
remote control commands with programming examples, and information on main-
tenance, instrument interfaces and error messages. Includes the contents of the
getting started manual.
The user manual is also available for download or for immediate display on the
Internet.
Data sheet and brochure
The data sheet contains the technical specifications of the R&S EDST300. It also
lists the firmware applications and their order numbers, and optional accessories.
The brochure provides an overview of the instrument and deals with the specific
characteristics.
Release notes and open source acknowledgment (OSA)
The release notes list new features, improvements and known issues of the cur-
rent firmware version, and describe the firmware installation.
Documentation overview
R&S®EDST300
9Getting Started 1179.5647.02 ─ 01
The software makes use of several valuable open source software packages. An
open-source acknowledgment document provides verbatim license texts of the
used open source software.
Application notes, application cards, white papers, etc.
These documents deal with special applications or background information on
particular topics.
See www.rohde-schwarz.com/appnotes.
Welcome to the R&S EDST300
R&S®EDST300
10Getting Started 1179.5647.02 ─ 01
3 Welcome to the R&S EDST300
The R&S EDST300 is an analyzer designed for installing, testing and servicing
pulsed terrestrial navigation systems like DME and TACAN ground equipment. Its
wide dynamic range and compact design make the R&S EDST300 ideal espe-
cially for wired and field measurements on DME and TACAN ground stations.
The R&S EDST300 provides high-precision stimulus and analysis functions for
DME / TACAN signals in the frequency range from 960 MHz to 1215 MHz. It per-
forms TX/RX measurements required for DME und TACAN ground stations in line
with the relevant civil and military standards accurately and efficiently.
The R&S EDST300 can precisely determine characteristic parameters such as
peak power, main delay, reply efficiency, and can decode the identifier of the
ground station to be tested. The instrument also measures the parameters of
TACAN stations (R&S EDST-K1 option) and performs in-depth pulse analysis
(R&S®EDST-K2 option).
The modular design of the R&S EDST300 provides a high degree of flexibility to
adapt it to the task at hand. An interrogator (R&S EDST-B2 option) with adjusta-
ble output power (-80 dBm to +30 dBm peak power) is available for distance
measurements. An internal battery (R&S EDST-B3 option) and a test antenna
(R&S EDST-Z1 option) deliver maximum flexibility when carrying out field mea-
surements. Measured data can be exported to a control system via remote con-
trol (LAN), or stored on a USB flash drive.
Indice
Altri manuali R&S Apparecchiature di prova
R&S
R&S RTO2000 Manuale utente
R&S
R&S CMW-KM5 Series Manuale utente
R&S
R&S RTB2K-COM4 Manuale utente
R&S
R&S CMW-KG8 Series Manuale utente
R&S
R&S HMC8015 Manuale utente
R&S
R&S RTA4000 Manuale utente
R&S
R&S RTO6 Manuale utente
R&S
R&S HMO72 Series Manuale utente
R&S
R&S RTE Manuale utente
R&S
R&S RTC1000 Manuale utente
Manuali Apparecchiature di prova popolari di altre marche
SMART
SMART KANAAD SBT XTREME 3G Series Manuale utente
Agilent Technologies
Agilent Technologies BERT Serial Manuale utente
Agilent Technologies
Agilent Technologies N3280A Manuale utente
Vernier
Vernier Go Direct Voltage Manuale utente
Lifeloc
Lifeloc R.A.D.A.R. Manuale utente
Fluke
Fluke T5-600 Istruzioni per l'uso e l'installazione
