Ricoh Shepherd-P1 Manuale di servizio

Technical Bulletin PAGE: 1/1

Model:

Shepherd-P1

Date:

1-Jun-18

No.:

RJ093001

At machine installation:

Make sure not to curve the optical fiber cable sharply shown below. If you do it, the

fiber cable will be broken.

[2.Installation] [Installing the Cable Bearer (Right)]

If the cable is broken, following errors may occur.

118: Setting up optical fiber cable communication has failed.

119: Setting up channel mapping has failed.

Detail

DO NOT curve the optical fiber cable within 65mm radius.

65mm

Subject: Caution for routing optical fiber cable

Prepared by:

Y.Kurohashi

From: 1st System Business Promotion Section, System

Business Department

Classification: Troubleshooting

Mechanical

Paper path

Product Safety

Part information

Electrical

Transmit/receive

Other ( )

Action required

Service manual revision

Retrofit information

Tier 2

Technical Bulletin PAGE: 1/1

Model:

Shepherd-P1

Date:

10-Sep-18

No.:

RJ093002

Subject:

Ticking sound from negative pressure valve

Prepared by:

Y.Kurohashi

From: 1st System Business Promotion Section, System

Business Department

Classification: Troubleshooting

Mechanical

Paper path

Part information

Electrical

Transmit/receive

Action required

Service manual revision

Retrofit information

Product Safety Other ( ) Tier 2

At machine installation:

Please explain the intermittent ticking sound from negative pressure valve is normal work

of the machine.

To keep negative pressure at the print heads all times, the electrical valves open and close

intermittently.

Therefore, there is the sound not only at printing but also at standby-mode.

Technical Bulletin PAGE: 1/5

Model:

Shepherd-P1

Date:

16-Oct-18

No.:

RJ093003

Subject: Changed the installation procedure for

installing the proximity sensors. Prepared by: Y.Kurohashi

From:

1st System Business Promotion Section, System

Business Department

Classification:

Troubleshooting

Mechanical

Paper path

Product Safety

Part information

Electrical

Transmit/receive

Other ( )

Action required

Service manual revision

Retrofit information

Tier 2

Service Manual Revision

[2. Installation] - [Installing the Proximity Sensors]

Changed the installation procedure for installing the proximity sensors.

１） Proximity Sensors have been changed as Accessories.

２） According to 1), installing procedure has been changed.

３） It requires Adjustment of light receiving amount after assembling the sensors.

The items in italics were corrected or added.

Procedure

Additional accessories

[For Left Rear], [For Left Front], [For Right Rear], [For Right Front]

Right Side(Receiver)

：

: Black Cable

Left Side(Emitter)

: Gray Cable

Technical Bulletin PAGE: 2/5

Model:

Shepherd-P1

Date:

16-Oct-18

No.:

RJ093003

Installing the Proximity Sensors

1. Check that the relay cables for assembling sensors are taped at 4 corners of Gantry

unit.

LR[A], RF[B], LF[C], RF[D]

Technical Bulletin PAGE: 3/5

Model:

Shepherd-P1

Date:

16-Oct-18

No.:

RJ093003

2. Remove twelve screws on the right side of the gantry on the right side of the gantry.

The six screws [A] are used for installing the proximity sensors in step 3, and the six

screws [B] are used for attaching the proximity sensor covers to the proximity sensors

in step 5.

3. Install the proximity sensors [A] and [B] as shown below.

Use the screws removed in step 2.

Right Side (Emitter)

Black Cable

Technical Bulletin PAGE: 4/5

Model:

Shepherd-P1

Date:

16-Oct-18

No.:

RJ093003

4. Install the two proximity sensors and proximity sensor cover (left) on the left side of the

gantry in the same way.

5. Connecting the cable of sensor with relay cable. [A]

Adjust the length of the cable by Inserting the excess length of the cable into the hole.

[B]

6. Adjust the light receiving amount.

Following steps are available after turning power on.

6-1. Check that the light level indication lamp turns green.

-If all 5 lamps turn on, installing procedure of the sensors are finished.

-If even one lamp does NOT turn on, adjust the level by following 7-2 step.

Lighting

Lighting-off

Target

Light level

Indication Lump

Technical Bulletin PAGE: 5/5

Model:

Shepherd-P1

Date:

16-Oct-18

No.:

RJ093003

6-2. Loosen the following two screws, then adjust the sensor position until all Light

level indication lamps turn on. After the adjustment, tighten the screws again.

Tighten each screw temporarily at first, then tightening the screws while checking the 5

lamps turning on.

7. Install the proximity sensor cover (right) [A] on the proximity sensors.

Use the five screws attached to the screw holes on the proximity sensors.

8. Fix the proximity sensor covers to the proximity sensors with the six screws removed

in step 2.

Technical Bulletin PAGE: 1/2

Model:

Shepherd-P1

Date:

31-Oct-18

No.:

RJ093004

Subject: Release information of the patch for added

Fine mode and Super Fine mode Prepared by: Y.Kurohashi

From: 1st System Business Promotion Section, System

Business Department

Classification: Troubleshooting

Mechanical

Paper path

Product Safety

Part information

Electrical

Transmit/receive

Other ( )

Action required

Service manual revision

Retrofit information

Tier 2

Outline:

Print Mode Ver.1.0.0.0 has been released for added Fine mode and Super Fine mode.

By installing this software, Fine mode and Super Fine mode are available in following

print modes.

-4C-W_Fine

-4C-W_Super Fine

-4C_Fine

-4C_Super Fine

- W-4C_Fine

- W-4C_Super Fine

Additional print modes are available at Print Mode selection tab.

Technical Bulletin PAGE: 2/2

Model:

Shepherd-P1

Date:

31-Oct-18

No.:

RJ093004

These modes are useful to reduce banding image like below photo.

Note:

-If customer needs higher quality print than High Quality mode, use these modes.

-Fine mode is Bi-directional print. Super Fine mode is uni-directional print.

-Super Fine is lowest productivity print mode. (Abt. one fifth productivity of Standard

mode)

-These modes are still available after Print Control Software is

newly updated. Not necessary to re-install them at each update of Print Control

software.

Technical Bulletin PAGE: 1/2

Model:

Shepherd-P1

Date: 1

-Nov-18

No.:

RJ093005

Subject: [NA model only] Precaution when working

near the transformer unit Prepared by: Y.Kurohashi

From: 1st System Business Promotion Section, System

Business Department

Classification: Troubleshooting

Mechanical

Paper path

Product Safety

Part information

Electrical

Transmit/receive

Other ( )

Action required

Service manual revision

Retrofit information

Tier 2

Outline:

For NA model Only

There is a transformer unit at following position. The transformer converts the voltage

from 220V to 380V. Though transformer unit is covered with metal gauze illustrated in

red frame below, please observe following precautions when working near there.

Precaution

・Make sure to turn off main power switch and disconnect the power supply

cable from the machine before starting work.

・Move the carriage unit above left side ink receiver before turn off main SW.

Altri manuali Ricoh Unità di controllo

Ricoh

Ricoh Aficio 480W Manuale di servizio

Ricoh

Ricoh Aficio 700 Manuale utente

Ricoh

Ricoh DHSB-R40 Manuale utente

Ricoh

Ricoh GX4 Manuale utente

Ricoh

Ricoh 411402 - EFI Fiery EB-105EX Controller Guida alla configurazione

Ricoh

Ricoh Be-C1 Manuale di servizio

Ricoh

Ricoh K-P3 Manuale di servizio

Ricoh

Ricoh HP4-R2 Manuale utente

Manuali Unità di controllo popolari di altre marche

Festo

Festo Compact Performance CP-FB6-E Manuale elenco delle parti

Elo TouchSystems

Elo TouchSystems DMS-SA19P-EXTME Manuale utente

JS Automation

JS Automation MPC3034A Manuale utente

JAUDT

JAUDT SW GII 6406 Series Guida rapida

Spektrum

Spektrum Air Module System Manuale utente

BOC Edwards

BOC Edwards Q Series Manuale utente

KHADAS

KHADAS BT Magic Manuale utente

Etherma

Etherma eNEXHO-IL Manuale utente

PMFoundations

PMFoundations Attenuverter Manuale utente

GEA

GEA VARIVENT Manuale utente

Walther Systemtechnik

Walther Systemtechnik VMS-05 Manuale utente

Altronix

Altronix LINQ8PD Istruzioni per il montaggio

Eaton

Eaton Powerware Series Manuale utente

WAGO

WAGO 750-407/040-000 Manuale utente

Sony

Sony CCU-590 Manuale utente

Graco

Graco 25D614 Manuale utente

Task Force Tips

Task Force Tips YE-RF-900 Manuale di programmazione

Shini

Shini SPV-U Series Manuale utente