ring TRADE PRO Manuale utente
1
SAFEGUARD YOUR JOURNEY
TRADE PRO
DASH CAM
USER GUIDE: RVEP1 RVEP2
2
WARNING
The Dash Cam must not be fitted in a position which obscures the driver’s view of the road
ahead. Depending on the country of use, recordings made with this device may be subject to
Data Protection Laws. Ensure these are complied with.
If the dash cam is to be used in a commercial environment e.g. taxi or truck, then CCTV
Regulations may apply. Playback of video which is visible to the driver whilst the vehicle is in
motion is prohibited in some countries.
Only use the supplied power adaptor, otherwise damage may occur to the dash cam.
Take care when cleaning the dash cam lens and only use a suitable lens cleaner and a soft
cloth. Do NOT expose this product to rain, moisture or water under any circumstances; doing
so may result in the risk of electric shock or fire.
Do NOT perform servicing other than that contained in the instruction manual, unless you
are qualified to do so. When installing in a vehicle, always place the device securely against
the windscreen and where possible conceal the power cable under the vehicles interior
trim. Make sure that the power cable doesn’t interfere with the driver’s controls such as the
steering wheel, pedals or gear lever.
Do NOT mount the dash cam in front of an airbag deployment area or in a position to obscure
any interior mirrors.
Do NOT operate whilst driving and only adjust settings or review recordings whilst stationary.
3
TABLE OF CONTENTS
Package Contents 4
Product Specification 5
Getting Started 6
Installation 7-8
Settings 9-10
Reformatting SD Card 11
Passwords 12
Reviewing Recordings 13-15
4
PACKAGE CONTENTS
CONFIGURATION
Dash Camera
Interior Camera (only with RVEP2)
Quick Start Guide
Window sticker
Trim removal tool
Hard wired power supply (fuse box)
Tool to remove lockable SD card hex screw
3M adhesive mount (+1 replacement 3M pad)
Lockable Micro SD slot
ON/OFF button
Record
Down
Up
Menu
Mode
5
DELIVERING THE TRUTH
Record vital evidence in the event of an incident. Protect yourself from insurance fraud, and in
some cases even lower your insurance costs.
Exceptional low light performance means Trade Pro dash cameras can provide vital evidence
even when driving at night.
Hassle free to install and use, they automatically switch on when you start the engine – so you
never miss a thing – and turn off once you park up – meaning no risk of draining your battery.
Loop recording will automatically save over old footage you no longer need: you don’t have to
clear or buy new SD cards. Important files can be locked to save them for later viewing.
The lockable MicroSD slot is designed to prevent tampering and password protected
software prevents alteration of captured footage.
*Once there is no external power input dash cam will no longer be powered
Specifications
Product Code RVEP1 RVEP2
Video Resolution (max) 720p @30fps 1080p @30fps
Display Size 2.4” 2.4”
Viewing Angle 110° 120°
Storage Card (included) 32GB 64GB
GPS function – 4
Password protection – 4
Audio Recording 4 4
Shock Sensor 4 4
Loop Recording 4 4
Auto Start/Stop 4 4
6
GETTING STARTED
To capture video and photos, requires the MicroSD card (pre-installed)
MicroSD Card
We recommend the use of the included MicroSD card for optimum performance.
Minimum Class 10 U1 16GB/32GB (Class 10 U3 for Optimum Performance)
SD CARD ERROR – SEE TROUBLESHOOTING GUIDE
If the above error is shown on your dash cam screen please see troubleshooting guide
(Page 9)
Helpful Information
This section helps you to eliminate problems the device may have under normal operation.
Failure to photograph/record video:
Check if there is enough free space on the micro SD card
Spontaneous stop at recording:
Too many video files stored. Only use at least class 10 U1 high-speed micro SD cards by
proven manufacturers.
When you try to view a photo/play a video file, the “wrong file” message appears:
File writing failure due to micro SD card file system error. Format the micro SD card.
Blurred image:
Ensure removal of lens sticker. Check for dirt on the lens. If there is any, wipe the lens with a
soft cloth before use (it is recommended to use special care products for the optics in order
not to damage the surface of the lens).
7
INSTALLING INTO VEHICLE
1. Ensure windscreen is clean of any moisture, dust and oils.
2. Position dash camera in a central location out of the line of sight of driver position
3. Connect hardwire kit to dash camera
4. Run hardwire kit through the trim directly to the fuse box on the vehicle
1.
2.
3.
4.
8
HARDWIRING INTO VEHICLE
1. Remove a fuse from an auxiliary power point in the fuse box
2. Insert the fuse into the end of the hardwire kit
3. Insert hardwire kit into fuse box in the slot vacated by the fuse removed in step 1
4. Connect fork section of hardwire kit to vehicle ground connection point
5. For Trade Pro2, connect interior camera to dash cam and situate on windscreen in front
of the driver position that is also out of the line of sight of the driver
6. Start Ignition to power dash cam
6.
4.
5.
3.
1.
2.
+
9
SETTINGS
Resolution
Set the resolution for the dash cam to record footage at. The higher resolution provides
clearer image (recommended) the lower resolution creates smaller recording file sizes.
Loop Recording
The dash cam has the option to save recordings on a loop of 3 or 5 minutes. The dash
cam will overwrite the oldest files saved to the MicroSD card to remove the requirement to
manually clear the memory space.
Date Stamp
The video recording can have the date and time at the point of filming stamped on the bottom
of the recording.
G-Sensor
G Sensor sensitivity can be adjusted. This is what detects forces which will automatically
protect the current recording in a collision.
The default setting for this will be set to medium sensitivity.
Parking Mode
During the case of a bump or knock whilst vehicle is parked, the dash cam can turn itself on
for 30 seconds to record the incident if this setting is activated in the settings (default OFF).
License Plate
The video recording can have licence plate stamped on the bottom of the recording.
To enable this enter the registration of the vehicle in the dash cam settings.
Protect File
Saved recordings can be locked manually to prevent them being over written by the loop
recording by using the Protect File setting.
Screen Saver
This setting allows you to switch the screen off when not required (default 30 Second timer).
Device Sounds
Buttons presses cause and sound to activate confirming the actuation. This be turned off in
the settings to make operation silent.
Language
The default language for the dash cam is English but can be changed to 10 others found in
the language settings.
10
SETTINGS
GPS (RVEP2)
The GPS tracks the coordinates and speed of the dash cam during recording that is stamped
on the bottom of the video recording. This can be set for metric, imperial or OFF.
Date/Time
Set the date & time on the dash cam by using the up and down buttons to change the
options.
Format SD Card
For optimum performance we recommend formatting your card on first
time use. Formatting erases all of your content, so be sure to download your photos and
videos first.
Default Settings
To return dash cam to original factory default settings select Menu (Setup) > Default Settings
Version
The dash cam’s current firmware version can be viewed in the settings menu.
Questo manuale è adatto per i seguenti modelli
4
Indice
Altri manuali ring Telecamera da cruscotto
ring
ring RDC10 Manuale utente
ring
ring RDC10 Manuale utente
ring
ring RBGDC200 Manuale utente
ring
ring Smart Dash Cam 2000 Manuale utente
ring
ring RSDCR1000 Manuale utente
ring
ring Smart Dash Cam 3000 Manuale utente
ring
ring RBGDC10 Manuale utente
ring
ring RBGDC50 Manuale utente
ring
ring 4000 Manuale utente
ring
ring Ring Dash Cam 1000 Manuale utente
