RIOTEC DC9257LP Manuale utente

1

Quick Guide

--DC9257LP (with Battery)

-DC9257LN (without Battery)

H92P

Connect to micro USB port of OTG device

2 H92P/H92N

3



* Before you use scanner, please switch to "C" for battery

charge for 3~4 hours.

*Under “C mode”, you can raise/lower soft-keyboard easily.



H92P Scan Holder is with Li-Ion battery inside. When in

charging, please use the original power adaptor of OTG

device (recommend). Through it, it charges both OTG

device and H92P internal battery at the same time. When in

low battery (Red LED flashing), please charge it

immediately.

LED Indicator Information

Green LED OFF Full charged (Charge mode)

Green LED ON Charging (Charge mode)

Red LED Flashing Low battery (Operation mode)

Attention: Under “Operation mode” please do not charging,

otherwise the OTG device's battery will be charging back to

H92P’s battery.



The touch trigger is in the central area of mini scanner. (for both side).

Please check the above drawing for your reference.

Installation

Before using scanner, please make sure that the OTG device is fully

charged.

1. Under USB HID interface

** When plugged into OTG device, it will be recognized and begin

to scan the barcode.

2. Under USB Serial interface

** Please install PL-2303 driver into your OTG device first. PL-2303

driver can be downloaded from Google Play

** Connect scanner to your OTG device, then, you can know which

serial port scanner connects to.

** The data you scan will be sent to serial port and your APP can

get the data from serial port directly.

Trigger

Area

O = Operation mode C = Char

e mode

LED Indicator



Suction Cup

PU Glue

(Can be used

repeatedly)

Micro USB

cable (OTG)

Mini

scanner

Micro USB

H92P with

Li- Ion Battery/

H92N without

Battery

LED Indicator

H92P only

2

Reset Configuration to Defaults

If you are unsure of the scanner configuration or have scanned the

incorrect codes, please scan from A1 to A3 for USB HID or B1 to B5 for

RS232 or USB Serial. This will reset the scanner to its factory defaults.

A1 B1

A2 B2

A3 B3

*Note: Please install PL-2303 driver for USB Serial.

Barcode Configuration Method:

(Flow chart for setup procedure :)

Start

Configuration

End

Configuration

Keyboard Country (For USB HID only)

Scan the appropriate country code as below to program the

keyboard layout for your country or language. As a general

rule, the following characters are supported, but need special

care for countries other than the United States:

@ | $ # { } [ ] = / ‘ \ < > ~

Bel

ium

Spain

Germany

Austria

Russia

Sweden Portu

Keyboard Country (For USB HID only)

Scan the appropriate country code as below to program the

keyboard layout for your country or language. As a general

rule, the following characters are supported, but need special

care for countries other than the United States:

@ | $ # { } [ ] = / ‘ \ < > ~

Japan

Denmark

Finland

France

Italy

Norway

urkey F

urkey

3

Barcode Configuration Method:

(Flow chart for setup procedure :)

Start

Configuration

End

Configuration

1D Symbologies – 1

ENABLE

Code 93

DISABLE

ENABLE

Code 39 DISABLE

1D Symbologies – 2

ENABLE

UPC-E

DISABLE

ENABLE

UPC-A

DISABLE

ENABLE

Interleaved

2 of 5

DISABLE

ENABLE

Code 128

DISABLE

ENABLE

GS1-128

UCC/EAN-128

DISABLE

1D Symbologies – 3

ENABLE EAN-8 DISABLE

ENABLE EAN-13 DISABLE

ENABLE Codabar DISABLE

ENABLE ISSN DISABLE

ENABLE ISBN DISABLE

ENABLE

GS1-Databar

(RSS) DISABLE

4

Barcode Configuration Method:

(Flow chart for setup procedure :)

Start

Configuration

End

Configuration

2D Symbologies

ENABLE

Data

Matrix DISABLE

ENABLE

QR Code DISABLE

ENABLE

Micro

QR Code DISABLE

ENABLE

PDF 417 DISABLE

Inter-Keystroke Delay (For USB HID only)

This parameter specifies the delay between emulated keystrokes.

No Delay

Short Delay

(20ms)

Long Delay

(40ms)

 Information in this document is subject to change without notice.

 For more information, please visit:

www.riotec.com.tw

R_200225_01

Questo manuale è adatto per i seguenti modelli

Altri manuali RIOTEC Lettore di codici a barre

RIOTEC

RIOTEC RIOSCAN iLS6303AS Manuale utente

RIOTEC

RIOTEC iDC9277A Manuale utente

RIOTEC

RIOTEC FS5100D Manuale utente

RIOTEC

RIOTEC iLS6302J BQ Manuale utente

RIOTEC

RIOTEC iLS6303XBU Manuale utente

RIOTEC

RIOTEC iDC9602NW Manuale utente

RIOTEC

RIOTEC iDC9607L Manuale utente

RIOTEC

RIOTEC DC9250 Manuale utente

RIOTEC

RIOTEC iDC9502N Manuale utente

RIOTEC

RIOTEC DC9257AP Manuale utente

RIOTEC

RIOTEC DC9257L Manuale utente

RIOTEC

RIOTEC DC9250DP Manuale utente

RIOTEC

RIOTEC LS6300E Manuale utente

RIOTEC

RIOTEC iLS6302ABU Manuale utente

RIOTEC

RIOTEC iDC9600C Manuale utente

RIOTEC

RIOTEC LS6303X Manuale utente

RIOTEC

RIOTEC LS6300E Manuale utente

RIOTEC

RIOTEC LS6302A Manuale utente

RIOTEC

RIOTEC LS6302A Manuale utente

RIOTEC

RIOTEC RIOSCAN iLS6302JS Manuale utente

RIOTEC

RIOTEC iLS6302ABQ Manuale utente

RIOTEC

RIOTEC iDC9272N Manuale utente

RIOTEC

RIOTEC LS6320E Manuale utente

RIOTEC

RIOTEC RIOSCAN iLS6308KS Manuale utente

Manuali Lettore di codici a barre popolari di altre marche

POSMicro

POSMicro Datalogic PowerScan D7100 Manuale utente

Marson

Marson MT780 Guida rapida alla configurazione

NCR

NCR RealPOS Manuale utente

Motorola

Motorola SE3300 Guida rapida alla configurazione

Element

Element P130BT Manuale utente

Motorola

Motorola Symbol LS3008 Manuale di installazione e funzionamento

Meec tools

Meec tools OBD-II / VAG Manuale utente

SICK

SICK CLP 100 Manuale utente

Royal Tag SA

Royal Tag SA I-Read Manuale utente

Welch Allyn

Welch Allyn IMAGETEAM 3800 Manuale utente

Meteor

Meteor 8310 Manuale utente

Denso

Denso BHT-500B Manuale utente

Datalogic

Datalogic Heron HD3130 Manuale utente

Motorola

Motorola MP6000 Istruzioni di montaggio

Newland

Newland NLS-HR15-BT Manuale utente

ARTDEV

ARTDEV AS-1310 Manuale utente

Aopos

Aopos AS290 Manuale utente

ENS

ENS 367-5455 Manuale utente